Black & Decker LST136-36V State of Charge Indicator Figure B, Checkingstate ofchargeduringuse

Page 7

TheLEAVINGTHEcharger andBATTERYINbattery packTHEcan CHARGERbe left connected with the green LED glowing indefinitely. The charger will keep the battery pack fresh and fully charged.

1IMPORTANT. Longest lifeCHARGINGand best performanceNOTES can be obtained if the battery pack is charged when the air temperature is between 60°F and 80°F (16°- 27°C). DO NOT charge the battery pack in an air temperature below +40°F (+4.5°C), or above +105°F (+40.5°C). This is important and will prevent serious damage to the battery pack.

2. The charger and battery pack may become warm to touch while charging. This is a normal condition, and does not indicate a problem. To facilitate the cooling of the battery pack after use, avoid placing the charger or battery pack in a warm environment such as in a metal shed, or an uninsulated trailer.

3. If the battery pack does not charge properly:

a. Check current at receptacle by plugging in a lamp or other appliance

b. Check to see if receptacle is connected to a light switch which turns power off when you turn out the lights.

c. Move charger and battery pack to a location where the surrounding air temperature is approximately 60°F - 80°F (16° - 27°C).

d. If charging problems persist, take the tool, battery pack and charger to your local service center.

4. The battery pack should be recharged when it fails to produce sufficient power on jobs which were easily done previously. DO NOT CONTINUE to use under these conditions. Follow the charging procedure. You may also charge a partially used pack whenever you desire with no adverse affect on the battery pack.

5. Foreign materials of a conductive nature such as, but not limited to, steel wool, aluminum foil, or any buildup of metallic particles should be kept away from charger cavities. Always unplug the charger from the power supply when there is no battery pack in the cavity. Unplug charger before attempting to clean.

6. Do not freeze or immerse charger in water or any other liquid.

insideWARNING:charger. Shock hazard. Do not allow any liquid to get Never attempt to open the battery pack for any

reason. If the plastic housing of the battery pack breaks or cracks, return to a service center for recycling.

The battery is equipped with a state of charge indicator. This can be

STATE OF CHARGE INDICATOR (FIGURE B)

 

used to display the current level of charge in the battery during use

and during charging. It does not

B

B1

indicate tool functionality and is subject

 

 

to variation based on product

B2

 

components, temperature and end-

 

 

user application.

 

 

• Press the state of charge indicator

 

 

Checkingstate ofchargeduringuse:

 

 

button (B1).

 

 

• The four LEDʼs (B2) will illuminate

 

 

indicating the percent of charge in

 

 

the battery. See chart in figure B.

 

 

• If LED light does not

 

 

illuminate,charge battery.

 

 

INSTALLING AND REMOVING THE BATTERY PACK

WARNING: Make certain the lock-off button is engaged to

prevent switch actuation before removing or installing battery.

Insert battery pack into tool until

C

TO INSTALL BATTERY PACK:

 

fully seated and an audible click is

 

heard (figure C). Make sure

 

battery pack is fully seated and

 

fully latched into position.

 

Depress the battery release button

 

TO REMOVE BATTERY PACK:

 

in the back of the battery pack and

 

pull battery pack out of tool.

 

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents 36V LITHIUMTRIMMER/ Edger Important Safety Warnings Instructions Table of ContentsReciprocations per minute AmperesVolts Hertz Watts Min Minutes Revolutions orElectrocution Then follow charging procedures outlined Important Safety Instructions For Battery PacksDo not operate charger with damaged cord or plug have Charging Procedure Long storage will not harm the battery pack or chargerInstalling and Removing the Battery Pack State of Charge Indicator Figure BCheckingstate ofchargeduringuse D4 figur D Assembly & AdjustmentAssemblytools Required not Supplied Attachingthe GuardOperatinginstructions Adjustingthe Height Ofthetool Figure HTrimming Mode Edging Mode FigurekEdging Switchingon and OFFPowercommand MAX POWER/ MAX RuntimeReplacing the Spool Replacement AccessoriesCUTTINGYour trimmerLINE /usesLINE Feeding Or visitMake a fold at the end Tangled more frequently than Black & Decker factory woundSpools. For best results, factory wound spools are ReplacingWear past this point MaintenanceTrouble Shooting Guide Line is not feeding, let lineService Information Trouble ShootingOverfeeding Line unravels when cap or spool is removed Replacement.1-800-544-6986 Full THREE-YEAR Home USE WarrantySee ‘Tools-Electric’ Avec Pile AU Lithium DE 36 Éviter LES Démarrages Accidentels Ne pas DirectivesdepremièreimportanceLire toutes les directives AvertissementQuelques exemples de ces produits chimiques Mise EN Garde risquAvertissement Certaines poussières produites par cet La Californie comme pouvant causer le cancer, les anomaliesAvant tout nettoyage Composants Pour LES Chargeurs DE PilesLe contenu des éléments de pile ouverts peut provoquer une Présence de liquides, de gaz ou de poussière inflammablesProcedure DE Charge Recommandations EN Matiere DE RangementFonctions DE Diagnostic DU Chargeur Avertissement Risque de choc électrique. Éviter la Pile EN Mauvais EtatFonction DE Suspension DU BLOC-PILES CHAUD/FROID Pile Laissee Dans LE ChargeurInsertion et retrait du bloc-piles Montage ET ReglageVérification de lʼétat de Charge durant lʼutilisationLiberation DU FIL DE Coupe Fixation DE LA Poignee Auxiliaire Figures F ET GReglage DE LA Hauteur DE LʼOUTILFIGURE H Régler LA Position DE LA Poignée Auxiliaire FIG. GMise EN Marche ET Arret Mode DE TaillageMode DE COUPE-BORDURES Figurek BordureCoupe EN Bordure Accessories DE RechangeFil de coupe/AVANCE DU FIL Fonctionnement DU TAILLE-BORDURESModedʼemploi Remplacement DE LA Bobine Figures P,Q ETPour alimenter lʼappareil ou pour toute autre raison CoupéesLE Sceau Srprc MC EntretienRembobiner LA Bobine Utiliseruniquement UN FIL Rond DE 1,65MM0,065 Podediametrefigures S,T ETUDepannage Problème SolutionSee ʻTools-Electricʼ Information SUR LES ReparationYellow Pages DE Litio DE 36 Manual DE Instrucciones Protector nunca utilice esta herramienta sin el protector Importantes Sobre SeguridadMenos de 30 m 100 pies de distancia Componentes Voltios Amperios Hertz Vatios Los símbolos y sus definiciones son los siguientesTerminal a tierra LEA Todas LAS Instrucciones Recomendaciones CON Respecto AL Almacenamiento Notas Importantes Sobre LA Carga Diagnostico DEL CargadorBateria Danada Dejar EL Paquete DE Baterias EN EL CargadorSuministradas Montaje Y AjusteIndicador DEL Estado DE LA Carga Figura B Herramientas Necesarias Para EL Ensamblaje noAjuste DE LA Alturade Laherramientafigurah Instalación DEL Mango AU Xiliar Figuras F Y GEmpuje el mango auxiliar F1 sobre el tubo F2 Ajuste DE LA PosiciónAtención La guía de Instrucciones DE OperaciónBordeado ADVERTENCIANuncaEncendidoy Apagado Máxima POTENCIA/MÁXIMOTIEMPO DE FuncionamientoCUERDADECORTE/ALIMENTACIÓNDELACUERDA AccesoriosderepuestoReemplazo DEL Carrete Diámetro Figuras S, T MM 0,0065 Pulgada DEEL Sello Rbrc Deteccion DE ProblemasGarantia Completade Tres Anos Para USO EN EL Hogar Informacionde MantenimientoIdentificacion DEL Producto Esta Garantia no Aplica CuandoSolamente Para Propositos DE Mexico March MEXICO, D.FEléctricas Tools-Electric Para Servicio y ventas
Related manuals
Manual 48 pages 3.22 Kb

LST136R, LST136-36V, LST136 specifications

Black & Decker has long been a trusted name in power tools and outdoor equipment, and their line of string trimmers is no exception. Among their notable offerings are the LST136, LST136-36V, and LST136R models. Each trimmer brings unique features and technologies to the table, designed to cater to a variety of gardening and landscaping needs.

The Black & Decker LST136 is a versatile cordless string trimmer powered by a 40V lithium-ion battery. This model is designed for ease of use and efficiency, making it an ideal choice for homeowners looking to maintain their lawns without the hassle of cords or gas. One of its standout features is the automatic feed spool, which ensures a continuous supply of line without the need for manual adjustments. Additionally, the trimmer offers a dual-line system for enhanced cutting performance, allowing you to tackle tougher weeds and thicker grass with ease.

The LST136-36V is a slightly more advanced version, boasting a 36V lithium-ion battery that provides longer run times and more power. This model is perfect for those who need a bit more oomph in their trimming tasks. It also features an adjustable height and handle, ensuring user comfort during extended use. The LST136-36V is designed for maneuverability, with a lightweight construction that makes it easy to navigate around flower beds, fences, and other obstacles in the yard.

Lastly, the LST136R offers a robust set of features, including a bump feed system that allows operators to release additional line with a simple tap on the ground. This model is also equipped with a 40V lithium-ion battery, similar to the LST136, and provides ample power for a variety of trimming jobs. The LST136R stands out with its ergonomic design, which prioritizes user comfort and reduces fatigue during long trimming sessions. Its built-in battery indicator lets users know how much charge is left, ensuring that you don’t run out of power mid-job.

In summary, the Black & Decker LST136, LST136-36V, and LST136R string trimmers each combine power, efficiency, and user-friendly features. Whether you’re a casual homeowner or a serious gardener, these trimmers provide reliable performance to keep your outdoor spaces looking their best. With innovations like automatic feed spools, adjustable settings, and lightweight designs, Black & Decker continues to lead the charge in outdoor power equipment.
Top Page Image Contents