Carrier 500 T/R user manual DataCOLD 500 R, DataCOLD 500 T

Page 2

INTRODUCTION

This manual is a guideline for the installation and use of the DataCOLD 500 T/R temperature recorders. To avoid loss of warranty coverage due to incompetent installation it is most essential to follow the instructions and recommendations of this manual.

DataCOLD 500 T/R recorders are developed and produced to conform to the applicable European and National norms for the delivery of chilled and frozen foods in transport vehicles.

DataCOLD 500 T/R recorders are tested and approved to the European EN12830 specification meeting the objectives of directives 92/1/EU and 93/43/EU and "e" mark approved following directive 95/54/CE.

DataCOLD 500 T/R can provide evidence of correct temperatures for every trip in the form of a delivery ticket, numerical or graphical print out. All data is stored with a date/time stamp in a large flash memory. Data will not be lost if power supply is disconnected. The real time clock is powered by an internal back-up battery.

The two recorder versions DataCOLD 500 T/R differ in looks. The R-Versionis suitable for in-cab installation and the T-Versionfor outside mounting on a trailer. Both versions are available with or without integrated printer. A printer can be retrofitted at any time, the recorder has been designed already with hardware- and software.

DataCOLD 500 R

The R-Versionhas been developed for mounting in the truck cab. The chassis of the recorder meets the dimensions of a DIN car radio and can be easily mounted in a free available radio slot. On the back side the connectors are designed for up to 4 Temperature sensors and 4 digital inputs, a power supply and digital outputs and a serial communication connector ( RS-232 ). If no free radio slot is available, the use of the optional universal mounting kit is strongly recommended.

DataCOLD 500 T

The T-Versionhas been developed especially for mounting outside on a body or trailer. The unit is fixed into a water proof enclosure. As on the R-version the connectors are on the back of the unit. Cabling is installed through watertight cable glands.

Both products are produced by Carrier Transicold in Germany. Carrier Transicold has a policy of continued development and improvements. Therefore products, manuals and technical information are subject to change without prior notice.

Page 2

62-61138-20 (02/03)

Page 1 Page 3
Image 2
Page 1 Page 3
Contents Installation USER’S Manual DataCOLD 500 R DataCOLD 500 TTable of Contents Yellow General descriptionBlue Green EditPositioning Connections InstallationPrinter Optional junction box MountingDataCOLD R-Version Optional Mounting kit CON4DataCOLD T-Version ConnectorsPower supply Is not Used for More than TEN 10 Days Configuration Alarm outputsWiring Display background lighting preferable for the R-VersionSupplementary installation Final testing Standard InstallationTemperature sensors Alarm signalUser menus Page Day end time Alarm menuDay start time Summer / wint time setting User settingsTime setting Date settingBuzzer volume setting Display back light settingKeyboard back light setting Buzzer frequency settingT1 Input On/off Menu 5 Temperature inputs settingsParameter menu Return airT3 Input On/off. Menu structure as T4 Input Menu 7 Compartment settings Menu 6 Digital inputs settingsDigital inputs setting On/off Compartment On/offMenu 9 Printer settings Menu Alarm settingsAlarm group On/off Delivery ticket settingsMenu 11 Communication settings Menu 10 General settingsTemperature units C 10.2 Sample rate Minutes11.2 COM2 RS-232 port setting Accessories and spare parts Part Number Designation62-61138-20 02/03 Enclosure a Enclosure B Replace paper roll Compartment settings Enclosure C Factory settingsTemperature inputs Factory setting Printer settingsEnclosure D Failure codes & Set correction factor procedure Enter PincodeEnclosure E Wiring diagrams Digital Inputs configuration example= GND = RXD = TXD = CTS
Top Page Image Contents