Briggs & Stratton 20288 manuel dutilisation Operation, How to Stop Your Pressure Washer

Page 10

Section 4: Operation

9.When starting engine, position yourself as recommended in Figure 9 and start engine according to instructions given in engine operator’s manual.Also see operating instructions tag located on the pressure washer.

Figure 9 - Recommended Starting Position

WARNING

Rapid retraction of starter cord (kickback) will pull hand and arm toward engine faster than you can let go.

Broken bones, fractures, bruises or sprains could result.

•ALWAYS point gun in safe direction and squeeze spray gun trigger, to release pressure and avoid kickback each time, before starting engine.

•When starting engine, pull cord slowly until resistance is felt and then pull rapidly to avoid kickback.

•After each starting attempt, where engine fails to run, always point gun in safe direction and squeeze spray gun trigger to release high pressure.

•Firmly grasp spray gun with both hands when using high pressure spray to avoid injury when gun kicks back.

NOTE: Always keep the throttle lever in the “Fast” position when operating the pressure washer.

WARNING

Running engines produce heat.Temperature of muffler and nearby areas can reach or exceed 150°F (65°C).

Severe burns can occur on contact.

Exhaust heat/gases can ignite combustibles, structures or damage fuel tank causing a fire.

•DO NOT touch hot surfaces and avoid hot exhaust gases.

•Allow equipment to cool before touching.

•Keep at least 5 ft. (152 cm) clearance on all sides of pressure washer including overhead.

•Code of Federal Regulation (CFR) Title 36 Parks, Forests, and Public Property require equipment powered by an internal combustion engine to have a spark arrester, maintained in effective working order, complying to USDA Forest service standard 5100-1C or later revision. In the State of California a spark arrester is required under section 4442 of the California Public resources code. Other states may have similar laws.

How to Stop Your Pressure Washer

1.Let engine idle for two minutes.

2.Turn engine off according to instructions given in engine operator’s manual.

3.ALWAYS point gun in a safe direction and squeeze spray gun trigger to release retained high water pressure.

WARNING

The high pressure stream of water that this equipment produces can pierce skin and its underlying tissues, leading to serious injury and possible amputation.

Spray gun traps high water pressure, even when engine is stopped and water is disconnected, which can cause injury.

•Keep high pressure hose connected to pump and spray gun while system is pressurized.

•ALWAYS point gun in safe direction and squeeze spray gun trigger, to release high pressure, every time you stop engine. Engage trigger lock when not in use.

IMPORTANT: Spray gun traps high water pressure, even when engine is stopped and water is disconnected.

4.Engage trigger lock on spray gun when not in use.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Operator’s Manual Manuel d’utilisation Safety Rules Table of ContentsEquipment Description When Transporting or Repairing Equipment Unintentional sparking can result in fire or electric shock High pressure spray may damage fragile items including glass Section Features and Controls Know Your Pressure WasherAssembly Assembly SectionPreparing Pressure Washer for USE Add Engine Oil and Fuel AssemblyChecklist Before Starting Engine Connect Hose and Water Supply to PumpOperation Section HOW to USE Your Pressure WasherHow to Start Your Pressure Washer Pressure Washer LocationHow to Stop Your Pressure Washer OperationUsage Tips How to Use the Adjustable NozzleApplying Detergent with the Adjustable Nozzle To apply detergent, follow these stepsAutomatic Cool Down System Cleaning Detergent Siphoning TubePressure Washer Rinsing Thermal ReliefGeneral Maintenance Recommendations Maintenance SectionSpecifications Pressure Washer MaintenanceRing Maintenance MaintenanceNozzle Maintenance Pump Oil MaintenancePreparing the Unit for Storage Engine MaintenanceStorage Section Storing the EngineTroubleshooting Section TroubleshootingProblem Cause Correction Page Page Limited Warranty Description DE L Équipement Règles de SécuritéTable DES Matières Règles DE SécuritéLors DE Lajout OU DE LA Vidange DU Carburant Lorsque Vous Réglez OU Réparez Votre Nettoyeur À Pression Règles de Sécurité Section Fonctions et Commandes Connaître Votre Pulvérisateur À PressionAssemblage Assemblage SectionPréparation DU Nettoyeur À Pression Pour Utilisation Raccorder le Tuyau et la Source Deau à la Pompe AssemblageAjoutez de lhuile et de lessence à moteur Liste de Vérifications Avant de Démarrer le MoteurComment Utiliser Votre Nettoyeur À Pression Emplacement de la Nettoyeur à PressionOpération Section Mettre Votre Nettoyeur à Pression en MarcheOpération Comment Arrêter Votre Nettoyeur à PressionComment Utiliser les Gicleurs Réglables Appliquer des Produits Détergents avec le Gicleur RéglableRincer le Nettoyeur à Haute Pression Tube de siphonnement du détergentCaractéristiques Recommandations Générale D’ENTRETIENEntretien Section Entretien DU Nettoyeur À PressionEntretien du Joint Torique EntretienEntretien du Gicleur Entretien de la Pompe à HuilePréparation DE L’UNITÉ Pour L’ENTREPOSAGE Rangement SectionEntretien DU Moteur Entreposage DU MoteurDépannage Section DépannageProblème Cause Correction Remarques RemarquesPériode DE Garantie

20288 specifications

Briggs & Stratton 20288 is a powerful and efficient portable generator designed to provide reliable backup power for home use, job sites, or outdoor activities. Known for its durable construction and innovative technologies, the model stands out as an ideal choice for consumers looking for both performance and convenience.

One of the main features of the Briggs & Stratton 20288 is its robust engine. Powered by the reliable Briggs & Stratton 306cc engine, this generator delivers a starting wattage of 7000 watts and a running wattage of 5500 watts. This capacity makes it suitable for running multiple appliances simultaneously, including refrigerators, lights, and power tools, making it a valuable asset during power outages or on worksites.

The generator is equipped with an advanced inverter technology, which provides clean, stable power output that is safe for sensitive electronics such as laptops, smartphones, and televisions. This feature ensures that you can confidently use your valuable devices without the risk of damage from voltage fluctuations. Furthermore, the inverter technology also allows for a quieter operation compared to traditional generators, making it ideal for residential areas or camping scenarios.

In addition to its power and technology, the Briggs & Stratton 20288 is built for durability and convenience. Its steel frame construction ensures that it can withstand the rigors of outdoor use while providing stability. The generator also features a foldable handle and never-flat wheels that enhance portability, allowing users to transport it with ease.

The generator includes several user-friendly features, such as an easy-to-read LED display that provides vital information such as remaining run time, power output, and maintenance reminders. The electric start function adds to the convenience, enabling users to start the generator quickly with the push of a button.

Safety is prioritized in the design of the Briggs & Stratton 20288. It is fitted with an automatic low-oil shutdown feature, which protects the engine from damage by stopping operation when oil levels are low. This, combined with a reliable fuel efficiency, ensures that users get optimal performance with minimal operational hassles.

Overall, the Briggs & Stratton 20288 portable generator combines impressive power, advanced technologies, and practical features, making it an excellent choice for individuals seeking a reliable generator that meets a variety of power needs while being easier to transport and operate.
Top Page Image Contents