Briggs & Stratton 20288 Pressure Washer Rinsing, Cleaning Detergent Siphoning Tube

Page 12

Section 4: Operation

4.Slide adjustable nozzle forward to low pressure mode. Detergent cannot be applied with nozzle in high pressure position.

5.Make sure garden hose is connected to water inlet. Check that high pressure hose is connected to spray gun and pump. Start engine.

6.Apply detergent to a dry surface, starting at lower portion of area to be washed and work upward, using long, even, overlapping strokes.

7.Allow detergent to "soak in" for 3-5 minutes before washing and rinsing. Reapply as needed to prevent surface from drying. DO NOT allow detergent to dry on (prevents streaking).

IMPORTANT: You must flush the chemical injection system after each use by placing the filter into a bucket of clean water, then run the pressure washer in low pressure for 1-2 minutes.

Pressure Washer Rinsing

For Rinsing:

1.Slide the nozzle backward to high pressure, press the trigger and wait for the detergent to clear.

NOTE: You can also stop detergent from flowing by simply removing chemical injection hose from bottle.

2.Keep the spray gun a safe distance from the area you plan to spray.

WARNING

High pressure spray could cause you to fall if you are too close to the cleaning surface.

•Keep spray nozzle between 8 to 24 inches away from cleaning surface.

•Operate this unit on a stable surface.

•Be extremely careful if you must use the pressure washer from a ladder, scaffolding or any other relatively unstable location.

•Firmly grasp spray gun with both hands when using high pressure spray to avoid injury if gun kicks back.

3.Apply a high pressure spray to a small area, then check the surface for damage. If no damage is found, it is okay to continue cleaning.

4.Start at the top of the area to be rinsed, working down with same overlapping strokes as you used for washing and applying detergent.

Cleaning Detergent Siphoning Tube

If you used the detergent siphoning tube, you must flush it with clean water before stopping the engine.

1.Place detergent siphoning tube/filter in a bucket full of clean water.

2.Engage trigger lock on spray gun.

3.Slide adjustable nozzle forward to low pressure position.

4.Flush for 1-2 minutes.

5.Shut off engine.

6.ALWAYS point gun in a safe direction and squeeze spray gun trigger to release retained high water pressure.

IMPORTANT: Spray gun traps high water pressure, even when engine is stopped and water is disconnected.

Automatic Cool Down System

(Thermal Relief)

If you run the engine on your pressure washer for

3-5 minutes without pressing the trigger on the spray gun, circulating water in the pump can reach temperatures above 125°F.The system engages to cool the pump by

discharging the warm water onto the ground.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Operator’s Manual Manuel d’utilisation Table of Contents Safety RulesEquipment Description When Transporting or Repairing Equipment Unintentional sparking can result in fire or electric shock High pressure spray may damage fragile items including glass Section Features and Controls Know Your Pressure WasherAssembly Section AssemblyPreparing Pressure Washer for USE Assembly Checklist Before Starting EngineAdd Engine Oil and Fuel Connect Hose and Water Supply to PumpHOW to USE Your Pressure Washer How to Start Your Pressure WasherOperation Section Pressure Washer LocationHow to Stop Your Pressure Washer OperationHow to Use the Adjustable Nozzle Applying Detergent with the Adjustable NozzleUsage Tips To apply detergent, follow these stepsCleaning Detergent Siphoning Tube Pressure Washer RinsingAutomatic Cool Down System Thermal ReliefMaintenance Section SpecificationsGeneral Maintenance Recommendations Pressure Washer MaintenanceMaintenance Nozzle MaintenanceRing Maintenance Pump Oil MaintenanceEngine Maintenance Storage SectionPreparing the Unit for Storage Storing the EngineSection Troubleshooting TroubleshootingProblem Cause Correction Page Page Limited Warranty Règles de Sécurité Table DES MatièresDescription DE L Équipement Règles DE SécuritéLors DE Lajout OU DE LA Vidange DU Carburant Lorsque Vous Réglez OU Réparez Votre Nettoyeur À Pression Règles de Sécurité Section Fonctions et Commandes Connaître Votre Pulvérisateur À PressionAssemblage Section AssemblagePréparation DU Nettoyeur À Pression Pour Utilisation Assemblage Ajoutez de lhuile et de lessence à moteurRaccorder le Tuyau et la Source Deau à la Pompe Liste de Vérifications Avant de Démarrer le MoteurEmplacement de la Nettoyeur à Pression Opération SectionComment Utiliser Votre Nettoyeur À Pression Mettre Votre Nettoyeur à Pression en MarcheOpération Comment Arrêter Votre Nettoyeur à PressionComment Utiliser les Gicleurs Réglables Appliquer des Produits Détergents avec le Gicleur RéglableRincer le Nettoyeur à Haute Pression Tube de siphonnement du détergentRecommandations Générale D’ENTRETIEN Entretien SectionCaractéristiques Entretien DU Nettoyeur À PressionEntretien Entretien du GicleurEntretien du Joint Torique Entretien de la Pompe à HuileRangement Section Entretien DU MoteurPréparation DE L’UNITÉ Pour L’ENTREPOSAGE Entreposage DU MoteurSection Dépannage DépannageProblème Cause Correction Remarques RemarquesPériode DE Garantie

20288 specifications

Briggs & Stratton 20288 is a powerful and efficient portable generator designed to provide reliable backup power for home use, job sites, or outdoor activities. Known for its durable construction and innovative technologies, the model stands out as an ideal choice for consumers looking for both performance and convenience.

One of the main features of the Briggs & Stratton 20288 is its robust engine. Powered by the reliable Briggs & Stratton 306cc engine, this generator delivers a starting wattage of 7000 watts and a running wattage of 5500 watts. This capacity makes it suitable for running multiple appliances simultaneously, including refrigerators, lights, and power tools, making it a valuable asset during power outages or on worksites.

The generator is equipped with an advanced inverter technology, which provides clean, stable power output that is safe for sensitive electronics such as laptops, smartphones, and televisions. This feature ensures that you can confidently use your valuable devices without the risk of damage from voltage fluctuations. Furthermore, the inverter technology also allows for a quieter operation compared to traditional generators, making it ideal for residential areas or camping scenarios.

In addition to its power and technology, the Briggs & Stratton 20288 is built for durability and convenience. Its steel frame construction ensures that it can withstand the rigors of outdoor use while providing stability. The generator also features a foldable handle and never-flat wheels that enhance portability, allowing users to transport it with ease.

The generator includes several user-friendly features, such as an easy-to-read LED display that provides vital information such as remaining run time, power output, and maintenance reminders. The electric start function adds to the convenience, enabling users to start the generator quickly with the push of a button.

Safety is prioritized in the design of the Briggs & Stratton 20288. It is fitted with an automatic low-oil shutdown feature, which protects the engine from damage by stopping operation when oil levels are low. This, combined with a reliable fuel efficiency, ensures that users get optimal performance with minimal operational hassles.

Overall, the Briggs & Stratton 20288 portable generator combines impressive power, advanced technologies, and practical features, making it an excellent choice for individuals seeking a reliable generator that meets a variety of power needs while being easier to transport and operate.
Top Page Image Contents