Pentair 200 installation manual Temperature Setting

Page 27

Section IV. Operation

27

 

 

• HEATING

The heating light is on any time the thermostat has signaled a call for heat which initializes the ignition safety circuit — the light comes on indicating successful firing of the main burners and stays on until the pool/spa reach the water temperature setting.

• SERVICE

The service light is off during normal operation of heater. The light only comes on if a problem with a control has occurred or when the heater is first firing. The problem must be investigated by the technician prior to attempts to fire the heater again.

TEMPERATURE SETTING

The heater comes factory set at 78° F. for the pool mode and 100° F. for the spa mode, using the up and down arrows, you can set the thermostats to a minimum temperature of 65° F., or a maximum of 104° F. If you desire to heat only one body of water, the thermostat is capable of an off mode. As an example, if you only wish to heat the spa and not the pool, simple depress and hold the pool down arrow, and the thermostat will lower its setting to 65° F. then go to an off mode. If there is a remote system connected to the heater, please see the special thermostat setting features under Heating Mode Selection & Remote mode.

HEATING MODE SELECTION

1.Off Mode: The heater will not come on. NOTE: The "Off" display on the Digital Display Temperature Controller does not mean that the heater is off. It only states that the pool or spa thermostat has been turned off.

2.Spa Mode: The heater will operate and heat the spa to the desired temperature.

3.Pool Mode: The heater will operate and heat the pool to the desired temperature.

4.Remote Mode: The DDTC is compatible with two and three wire remote control systems. In order to operate by a remote control system, the REMOTE mode must be selected on the front panel. When the REMOTE mode is selected, the REMOTE LED will light up.

REMOTE CONTROL

THE TWO-WIRE REMOTE CONTROL SYSTEM is typically installed and connected to the heater for spa heating. The two-wire remote system is usually provided with a water temperature sensor that monitors the system temperature and turns the heater on or off in response to the temperature of the spa. To heat a spa, it should be connected to terminals J6 and J8. Pool heating remote control would require connecting to terminals J5 and J8. If the REMOTE mode is set at the front panel LED light, the DDTC will respond to a contact closure by remote system and heater will operate until the remote system temperature setting is satisfied.

NOTE: With this type of two-wire remote, with its own temperature sensors and system control, using the up arrows on the front of the DDTC, hold down the up arrow until you reach the maximum setting of 104° F., this allows the remote system thermostat to operate the heater at any set-point below 104° F., the heater thermostats then act as a secondary controller if water temperature reaches 104° F.

THE THREE-WIRE REMOTE CONTROL SYSTEM will be connected to terminals J5, J6 & J8. J8 is the common terminal. If the heater is in the REMOTE mode, the DDTC will monitor the terminals and respond to a contact closure between J5 & J8 or J6 & J8. A contact closure between J5 & J8 will cause the DDTC to switch to the POOL setting and control the heater to the DDTC pool set-point temperature. A contact closure between J6 & J8 will cause the DDTC to switch to the SPA setting and control the heater to the DDTC spa set-point temperature. If only heating the spa, then depress the pool down arrow until the display goes to “Off”.

Rev. G • Rév. G 5-27-04

P/N • Réf. 472090

Page 26 Page 28
Image 27
Page 26 Page 28
Contents MiniMax NT Pool & Spa Heaters Table of Contents Heater Identification Information HIN Heater Identification InformationImportant Notices Warranty InformationCode Requirements Consumer Information and SafetySpecifications Installation InstructionsManual BY-PASS Below Pool InstallationPlumbing Connections ValvesReversing Headers Water ConnectionsReversible Inlet/Outlet Connection, cont’d GAS Line Installations GAS ConnectionsSediment Traps Pipe Sizing for GAS Line Connections GAS Pipe SizingGAS Pressure Requirements Testing GAS PressureIndoor Venting General Requirements Outdoor Shelter Installation Canada Indoor Installation USA onlyCombustion AIR Supply Vent AdaptorsFits ALL Models Section Outdoor Vent KIT Outdoor Installation Venting Guidelines Side ViewElectrical Connections Electrical Rating 60 Hz 120 / 240 Volts AC, single phaseVolts AC MiniMax NT TSI/DDTC Wiring Diagram Wiring DIAGRAM-NT STD & TSI with DdtcMinimax NT HSI Electronic Ignition LIGHTING/OPERATION Basic System OperationThermal Fuse Safety ControlsVacuum AIR Pressure FAN Switch Water Pressure SwitchFailure to Light the BURNER-LOCK OUT Heat ModeHigh Limits Operation of Ignition ModuleSystem Indicator Lights Digital Display Temperature Controller DdtcSection IV. Operation SET UP Temperature Setting Troubleshooting Ddtc Troubleshooting InstructionService CHECKS-IGNITION Module Troubleshooting GeneralEnergy Saving Tips Maintenance InstructionWinter Operation Spring and Fall OperationPool and SPA Water Chemical BalanceReplacement Parts NT STD & TSI w/DDTC Réf Rev. G Rév. G Rev. G Rév. G Réf Pentair Pool Products, Inc Chauffe-eau pour piscine et spa MiniMax NT Guide Dinstallation ET DE FonctionnementTable des matières Information Pour Lidentification DU CHAUFFE-EAU Information Pour Lidentification DU CHAUFFE-EAUGarantie Consignes ImportantesConformité AUX Codes Mise EN GardeSpécifications Consignes dinstallationsRaccords DE Plomberie SoupapesDérivation Manuelle Collecteurs réversibles Raccordements DES Conduites DeauRaccords dentrée et de sortie réversibles, suite Installations DE LA Conduite DE GAZ Raccordement DES Conduites DE GAZCollecteurs DE Sédiment Mesure DES Tuyaux Pour Raccords D’ARRIVÉE DE GAZ Dimension DES Tuyaux DE GAZExigences Pour LA Pression DE GAZ Vérification DE LA Pression DE GAZVentilation Intérieur Exigences Générales Installation Intérieure États-Unis Uniquement Admission Dair DE Combustion Adaptateurs DaérationConvient À Tous LES Modèles ApprovisionnementdAir Terminaison de la ventilation Ensemble DE Ventilation Pour LextérieurClassement électrique 60 Hz 120/240 Volts c.a. monophasé Raccordements ÉlectriquesVolts CA Réf Rev. G Rév Fonctionnement Générale DU Système Consignes de FonctionnementFusible Thermique Contrôles DE SécuritéCommutateur Ventilateur DE Pression DU Vide Dair Commutateur DE Pression DeauÉchec DE LA Flamme Rallumage Mode ChaleurHautes Limites Verrouillage EN CAS Déchec DallumageTémoins Indicateurs DU Système Thermostat À Affichage NumériqueSection IV. Fonctionnement Réglage DU Thermostat Réglage DE LA Temperature Dépannage Thermostat a Affichage Numerique Consignes DE DépannageVerifications Dentretien Module Dallumage Consignes DE DépannageSoupape DE Surpression Conseils Pour Économies DénergieFonctionnement EN Hiver Fonctionnement AU Printemps ET EN AutomneEAU DE Piscine ET DE SPA Équilibre Chimique DE LeauFORPour Modèle STD Réf Rev. G Rév. G Rev. G Rév. G Réf Veuillez Concerver CE Guide Dinstruction

200 specifications

The Pentair 200 is a sophisticated pool and spa control system designed to offer unmatched convenience, efficiency, and safety for users looking to enhance their aquatic experience. With cutting-edge technologies and a user-friendly interface, the Pentair 200 stands out as a leading solution in the pool management industry.

One of the main features of the Pentair 200 is its advanced automation capabilities. It allows users to control various aspects of their pool and spa, including lighting, heating, and filtration, all from a single control panel or a mobile app. This automation not only enhances usability but also ensures optimal performance, significantly reducing energy consumption compared to manual systems.

The integration with smart technology is another hallmark of the Pentair 200. Users can access the system remotely using their smartphones or tablets, allowing them to manage their pool settings from anywhere. This feature is particularly beneficial for those who may want to ensure their pool is ready for a gathering or simply wish to make adjustments while away from home.

The Pentair 200 is also designed with safety features in mind. It includes multiple protection mechanisms to prevent overheating and ensure regular operational safety, contributing to peace of mind for pool owners. Moreover, the easy-to-understand interface makes programming the system a breeze, even for those who may not be technologically inclined.

Efficiency is paramount in pool management, and the Pentair 200 excels in this area with energy-efficient technologies. Its variable-speed pump capabilities optimize energy usage depending on the specific needs of the pool, thereby resulting in lower utility bills and a reduced environmental impact.

Another notable characteristic is the system's durability and reliability. Constructed with high-quality materials and backed by Pentair's reputation in the industry, the 200 model is built to withstand various environmental conditions and provide consistent performance over time.

In summary, the Pentair 200 is a cutting-edge pool control system that enhances convenience, safety, and energy efficiency. Its advanced automation and smart technology integration make it a standout choice for modern pool owners. With the ability to manage their aquatic environments effectively and efficiently, users can enjoy their pools and spas with greater peace of mind.
Top Page Image Contents