Pentair 200 installation manual Indoor Installation USA only, Outdoor Shelter Installation Canada

Page 14

Section III. Installation

14

 

 

INDOOR INSTALLATION (USA ONLY)

OUTDOOR SHELTER INSTALLATION (CANADA)

See page 15 for Vent Adaptors

All products of combustion and vent gases must be completely removed to the outside atmosphere through a vent pipe which is connected to the stack adaptor. A vent pipe extension of the same size must be connected to the vent adaptor and extended at least 2 feet higher than highest point of the roof within a 10 foot horizontal radius, and at least 3 ft. higher than the point at which it passes through the roof, or as permitted by local code; see Figures 6, 7 and 12. The vent should terminate with an approved vent cap (weather cap) for protection against rain or blockage by snow. Insulated vent pipe and an approved roof jack shall be employed through the roof penetration.

Vent Cap and Riser Furnished by Installer

Optional

Side

Wall Vent

Heater

Chimney or Gas Vent

Outlet Air

Opening

Inlet Air

Opening

Figure 6.

The heater must be located as close as practical to a chimney or gas vent.

CAUTION

The heater should be installed at least 5 feet away from the pool or spa.

 

 

 

 

 

 

Chimney or Gas Vent

 

 

 

 

 

 

Vent Cap and

 

 

 

 

 

 

 

 

 

 

Riser Furnished

 

 

 

 

by Installer

 

 

 

 

 

 

 

 

 

 

 

The heater must be placed in a suitable room with adequate ventilation and on a leveled floor, where leakage from heat exchanger or water connections will not result in damage to the area adjacent to the heater or the structure. When such locations cannot be avoided, it is recommended that a suitable drain pan with adequate drainage, be installed under the heater. The pan must not restrict air flow.

It is recommended to install the heater on fire-resistance slabs. Do not install the heater directly on a combustible wood floor without placing a non-combustible material between the floor and the heater. Heaters must NEVER

Optional

Side

Wall Vent

Heater

Outlet Air Opening

Inlet Air Opening

be installed directly on carpeting.

Installations in basements, garages, or underground structures where flammable liquids may be stored must have the heater elevated 18 inches from the floor. The following minimum clearances from combustible materials must be provided.

 

 

INSTALLATION

 

 

SIDE

 

 

 

INDOOR

 

 

 

OF

OUTDOOR

 

 

(Outrdoor Shelter)

 

 

HEATER

 

 

 

 

 

 

 

 

INCHES

INCHES

 

 

 

 

 

 

 

WATER PIPING

18

18

 

 

 

 

 

 

 

BLANK

6

6

 

 

 

 

 

 

 

REAR

6

6

 

 

 

 

 

 

 

TOP *

18

Open Un-roofed Area

 

 

 

 

 

 

 

FRONT

24

24

 

 

 

 

 

 

 

* To ceiling or roof.

 

Table 11.

 

 

 

 

P/N • Réf. 472090

 

 

 

Figure 7.

The heater should not be installed closer than 6 inches to any fences, walls or shrubs at any side or back, nor closer than 18 inches at the plumbing side. A minimum clearance of 24 inches must be maintained at the front of the heater.

 

 

6"

 

 

DOOR

6"

 

24"

 

 

 

 

 

18"

 

Figure 8.

 

 

 

 

 

Rev. G • Rév. G

5-27-04

Page 13 Page 15
Image 14
Page 13 Page 15
Contents MiniMax NT Pool & Spa Heaters Table of Contents Heater Identification Information Heater Identification Information HINWarranty Information Important NoticesConsumer Information and Safety Code RequirementsInstallation Instructions SpecificationsValves Below Pool InstallationPlumbing Connections Manual BY-PASSWater Connections Reversing HeadersReversible Inlet/Outlet Connection, cont’d Sediment Traps GAS Line InstallationsGAS Connections GAS Pipe Sizing Pipe Sizing for GAS Line ConnectionsTesting GAS Pressure GAS Pressure RequirementsIndoor Venting General Requirements Indoor Installation USA only Outdoor Shelter Installation CanadaFits ALL Models Combustion AIR SupplyVent Adaptors Section Outdoor Installation Venting Guidelines Side View Outdoor Vent KITElectrical Rating 60 Hz 120 / 240 Volts AC, single phase Electrical ConnectionsVolts AC Wiring DIAGRAM-NT STD & TSI with Ddtc MiniMax NT TSI/DDTC Wiring DiagramBasic System Operation Minimax NT HSI Electronic Ignition LIGHTING/OPERATIONWater Pressure Switch Safety ControlsVacuum AIR Pressure FAN Switch Thermal FuseOperation of Ignition Module Heat ModeHigh Limits Failure to Light the BURNER-LOCK OUTDigital Display Temperature Controller Ddtc System Indicator LightsSection IV. Operation SET UP Temperature Setting Troubleshooting Instruction Troubleshooting DdtcTroubleshooting General Service CHECKS-IGNITION ModuleMaintenance Instruction Energy Saving TipsSpring and Fall Operation Winter OperationChemical Balance Pool and SPA WaterReplacement Parts NT STD & TSI w/DDTC Réf Rev. G Rév. G Rev. G Rév. G Réf Pentair Pool Products, Inc Guide Dinstallation ET DE Fonctionnement Chauffe-eau pour piscine et spa MiniMax NTTable des matières Information Pour Lidentification DU CHAUFFE-EAU Information Pour Lidentification DU CHAUFFE-EAUConsignes Importantes GarantieMise EN Garde Conformité AUX CodesConsignes dinstallations SpécificationsDérivation Manuelle Raccords DE PlomberieSoupapes Raccordements DES Conduites Deau Collecteurs réversiblesRaccords dentrée et de sortie réversibles, suite Collecteurs DE Sédiment Installations DE LA Conduite DE GAZRaccordement DES Conduites DE GAZ Dimension DES Tuyaux DE GAZ Mesure DES Tuyaux Pour Raccords D’ARRIVÉE DE GAZVérification DE LA Pression DE GAZ Exigences Pour LA Pression DE GAZVentilation Intérieur Exigences Générales Installation Intérieure États-Unis Uniquement Convient À Tous LES Modèles Admission Dair DE CombustionAdaptateurs Daération ApprovisionnementdAir Ensemble DE Ventilation Pour Lextérieur Terminaison de la ventilationRaccordements Électriques Classement électrique 60 Hz 120/240 Volts c.a. monophaséVolts CA Réf Rev. G Rév Consignes de Fonctionnement Fonctionnement Générale DU SystèmeCommutateur DE Pression Deau Contrôles DE SécuritéCommutateur Ventilateur DE Pression DU Vide Dair Fusible ThermiqueVerrouillage EN CAS Déchec Dallumage Mode ChaleurHautes Limites Échec DE LA Flamme RallumageThermostat À Affichage Numérique Témoins Indicateurs DU SystèmeSection IV. Fonctionnement Réglage DU Thermostat Réglage DE LA Temperature Consignes DE Dépannage Dépannage Thermostat a Affichage NumeriqueConsignes DE Dépannage Verifications Dentretien Module DallumageConseils Pour Économies Dénergie Soupape DE SurpressionFonctionnement AU Printemps ET EN Automne Fonctionnement EN HiverÉquilibre Chimique DE Leau EAU DE Piscine ET DE SPAFORPour Modèle STD Réf Rev. G Rév. G Rev. G Rév. G Réf Veuillez Concerver CE Guide Dinstruction

200 specifications

The Pentair 200 is a sophisticated pool and spa control system designed to offer unmatched convenience, efficiency, and safety for users looking to enhance their aquatic experience. With cutting-edge technologies and a user-friendly interface, the Pentair 200 stands out as a leading solution in the pool management industry.

One of the main features of the Pentair 200 is its advanced automation capabilities. It allows users to control various aspects of their pool and spa, including lighting, heating, and filtration, all from a single control panel or a mobile app. This automation not only enhances usability but also ensures optimal performance, significantly reducing energy consumption compared to manual systems.

The integration with smart technology is another hallmark of the Pentair 200. Users can access the system remotely using their smartphones or tablets, allowing them to manage their pool settings from anywhere. This feature is particularly beneficial for those who may want to ensure their pool is ready for a gathering or simply wish to make adjustments while away from home.

The Pentair 200 is also designed with safety features in mind. It includes multiple protection mechanisms to prevent overheating and ensure regular operational safety, contributing to peace of mind for pool owners. Moreover, the easy-to-understand interface makes programming the system a breeze, even for those who may not be technologically inclined.

Efficiency is paramount in pool management, and the Pentair 200 excels in this area with energy-efficient technologies. Its variable-speed pump capabilities optimize energy usage depending on the specific needs of the pool, thereby resulting in lower utility bills and a reduced environmental impact.

Another notable characteristic is the system's durability and reliability. Constructed with high-quality materials and backed by Pentair's reputation in the industry, the 200 model is built to withstand various environmental conditions and provide consistent performance over time.

In summary, the Pentair 200 is a cutting-edge pool control system that enhances convenience, safety, and energy efficiency. Its advanced automation and smart technology integration make it a standout choice for modern pool owners. With the ability to manage their aquatic environments effectively and efficiently, users can enjoy their pools and spas with greater peace of mind.
Top Page Image Contents