Pentair 200 installation manual Water Connections, Reversing Headers

Page 8

Section III. Installation

8

 

 

WATER CONNECTIONS

Reversing Headers —

Reversible Inlet/Outlet Connection

The MiniMax NT Series heater is factory assembled with right side inlet/outlet water connections. The inlet/outlet header can be reversed for left side water connections without removing the heat exchanger.

Reversing Water Connections

Tools required:

Phillips Screw Driver

9/16 in. Socket and Wrench 1/2 in. & 9/16 in. Open Wrench

1.Remove the right and left large access doors. It is not necessary to remove the top of the heater to gain access to the headers.

2.Disconnect all wires from the high-limit switches except the short jumper wire.

NOTE

Do NOT remove the high-limit and pressure switches or the thermistor from the front header during the reversing procedure, as they will be in the proper location when installed on the left side.

3.Disconnect the water pressure switch wiring.

4.Disconnect the temperature sensor wires from the circuit board and feed them back to the header.

5.Remove the 8 bolts holding the main inlet/outlet head.

P/N • Réf. 472090

Rev. G • Rév. G 5-27-04

Page 7 Page 9
Image 8
Page 7 Page 9
Contents MiniMax NT Pool & Spa Heaters Table of Contents Heater Identification Information Heater Identification Information HINWarranty Information Important NoticesConsumer Information and Safety Code RequirementsInstallation Instructions SpecificationsBelow Pool Installation Plumbing ConnectionsValves Manual BY-PASSWater Connections Reversing HeadersReversible Inlet/Outlet Connection, cont’d Sediment Traps GAS Line InstallationsGAS Connections GAS Pipe Sizing Pipe Sizing for GAS Line ConnectionsTesting GAS Pressure GAS Pressure RequirementsIndoor Venting General Requirements Indoor Installation USA only Outdoor Shelter Installation CanadaFits ALL Models Combustion AIR SupplyVent Adaptors Section Outdoor Installation Venting Guidelines Side View Outdoor Vent KITElectrical Rating 60 Hz 120 / 240 Volts AC, single phase Electrical ConnectionsVolts AC Wiring DIAGRAM-NT STD & TSI with Ddtc MiniMax NT TSI/DDTC Wiring DiagramBasic System Operation Minimax NT HSI Electronic Ignition LIGHTING/OPERATIONSafety Controls Vacuum AIR Pressure FAN SwitchWater Pressure Switch Thermal FuseHeat Mode High LimitsOperation of Ignition Module Failure to Light the BURNER-LOCK OUTDigital Display Temperature Controller Ddtc System Indicator LightsSection IV. Operation SET UP Temperature Setting Troubleshooting Instruction Troubleshooting DdtcTroubleshooting General Service CHECKS-IGNITION ModuleMaintenance Instruction Energy Saving TipsSpring and Fall Operation Winter OperationChemical Balance Pool and SPA WaterReplacement Parts NT STD & TSI w/DDTC Réf Rev. G Rév. G Rev. G Rév. G Réf Pentair Pool Products, Inc Guide Dinstallation ET DE Fonctionnement Chauffe-eau pour piscine et spa MiniMax NTTable des matières Information Pour Lidentification DU CHAUFFE-EAU Information Pour Lidentification DU CHAUFFE-EAUConsignes Importantes GarantieMise EN Garde Conformité AUX CodesConsignes dinstallations SpécificationsDérivation Manuelle Raccords DE PlomberieSoupapes Raccordements DES Conduites Deau Collecteurs réversiblesRaccords dentrée et de sortie réversibles, suite Collecteurs DE Sédiment Installations DE LA Conduite DE GAZRaccordement DES Conduites DE GAZ Dimension DES Tuyaux DE GAZ Mesure DES Tuyaux Pour Raccords D’ARRIVÉE DE GAZVérification DE LA Pression DE GAZ Exigences Pour LA Pression DE GAZVentilation Intérieur Exigences Générales Installation Intérieure États-Unis Uniquement Convient À Tous LES Modèles Admission Dair DE CombustionAdaptateurs Daération ApprovisionnementdAir Ensemble DE Ventilation Pour Lextérieur Terminaison de la ventilationRaccordements Électriques Classement électrique 60 Hz 120/240 Volts c.a. monophaséVolts CA Réf Rev. G Rév Consignes de Fonctionnement Fonctionnement Générale DU SystèmeContrôles DE Sécurité Commutateur Ventilateur DE Pression DU Vide DairCommutateur DE Pression Deau Fusible ThermiqueMode Chaleur Hautes LimitesVerrouillage EN CAS Déchec Dallumage Échec DE LA Flamme RallumageThermostat À Affichage Numérique Témoins Indicateurs DU SystèmeSection IV. Fonctionnement Réglage DU Thermostat Réglage DE LA Temperature Consignes DE Dépannage Dépannage Thermostat a Affichage NumeriqueConsignes DE Dépannage Verifications Dentretien Module DallumageConseils Pour Économies Dénergie Soupape DE SurpressionFonctionnement AU Printemps ET EN Automne Fonctionnement EN HiverÉquilibre Chimique DE Leau EAU DE Piscine ET DE SPAFORPour Modèle STD Réf Rev. G Rév. G Rev. G Rév. G Réf Veuillez Concerver CE Guide Dinstruction

200 specifications

The Pentair 200 is a sophisticated pool and spa control system designed to offer unmatched convenience, efficiency, and safety for users looking to enhance their aquatic experience. With cutting-edge technologies and a user-friendly interface, the Pentair 200 stands out as a leading solution in the pool management industry.

One of the main features of the Pentair 200 is its advanced automation capabilities. It allows users to control various aspects of their pool and spa, including lighting, heating, and filtration, all from a single control panel or a mobile app. This automation not only enhances usability but also ensures optimal performance, significantly reducing energy consumption compared to manual systems.

The integration with smart technology is another hallmark of the Pentair 200. Users can access the system remotely using their smartphones or tablets, allowing them to manage their pool settings from anywhere. This feature is particularly beneficial for those who may want to ensure their pool is ready for a gathering or simply wish to make adjustments while away from home.

The Pentair 200 is also designed with safety features in mind. It includes multiple protection mechanisms to prevent overheating and ensure regular operational safety, contributing to peace of mind for pool owners. Moreover, the easy-to-understand interface makes programming the system a breeze, even for those who may not be technologically inclined.

Efficiency is paramount in pool management, and the Pentair 200 excels in this area with energy-efficient technologies. Its variable-speed pump capabilities optimize energy usage depending on the specific needs of the pool, thereby resulting in lower utility bills and a reduced environmental impact.

Another notable characteristic is the system's durability and reliability. Constructed with high-quality materials and backed by Pentair's reputation in the industry, the 200 model is built to withstand various environmental conditions and provide consistent performance over time.

In summary, the Pentair 200 is a cutting-edge pool control system that enhances convenience, safety, and energy efficiency. Its advanced automation and smart technology integration make it a standout choice for modern pool owners. With the ability to manage their aquatic environments effectively and efficiently, users can enjoy their pools and spas with greater peace of mind.
Top Page Image Contents