Pentair 200 installation manual Troubleshooting General, Service CHECKS-IGNITION Module

Page 29

Section V. Troubleshooting

29

 

 

TROUBLESHOOTING (GENERAL)

Possible Cause

Remedy

 

 

Heater will not come on

 

 

 

 

Check if electrical connections are

Automatic ignition system fails

correct and securely fastened –

 

If YES, call serviceperson.

Pump not running

Place pump in operation

Pump air locked

Check for leaks

Filter dirty

Clean filter

Pump strainer clogged

Clean strainer

Defective wiring or connection

Repair or replace wires

Defective pressure switch

Replace switch

Defective gas controls

Call serviceperson

On-Off switch in "OFF" position

Turn switch to "ON"

Heater Short Cycling (Rapid On and Off Operation)

 

 

Insufficient water flow

Clean filter and pump strainer

Defective wiring

Repair or replace wiring

Defective flow valve or out of adjustment

Call serviceperson

Defective hi-limit and/or thermostat

Call serviceperson

Heater Makes Knocking Noises,

make sure all valves on system are open.

Heater operating after pump has shut off

 

 

Shut off gas supply and call serviceperson

Heater exchanger scaled

 

 

Shut off gas supply and call serviceperson

 

 

 

 

 

SERVICE CHECKS—IGNITION MODULE

 

 

 

 

 

Symptom

Cause/Cure

 

 

 

 

 

 

 

1.

Dead

A. Miswired

 

 

 

 

B. Transformer bad

 

 

 

 

C.

Fuse/Circuit breaker bad

 

 

 

 

D.

Bad control

 

 

 

 

 

 

 

 

2.

Thermostat on—no ignition

A.

Miswired

 

 

 

 

B. Bad thermostat no voltage at terminal

 

 

 

 

 

 

 

 

3.

Valve on, no ignition

A.

Defective ignitor

 

 

 

 

B.

Miswired

 

 

 

 

C. Bad control (check voltage at ignitor)

 

 

 

 

 

 

 

 

4.

Ignitor on, no valve action

A.

Valve coil open

 

 

 

 

B. Open valve wire

 

 

 

 

C. Bad control (check voltage)

 

 

 

 

 

 

 

5.

Flame okay during

A. Bad flame sensor

 

 

 

Try For Ignition (TFI),

B.

Bad wires

 

 

 

no flame sense (after TFI)

C.

Poor ground at burner

 

 

 

 

D. Poor flame (check flame current)

 

 

 

 

 

 

 

 

Rev. G • Rév. G 5-27-04

P/N • Réf. 472090

Image 29
Contents MiniMax NT Pool & Spa Heaters Table of Contents Heater Identification Information HIN Heater Identification InformationImportant Notices Warranty InformationCode Requirements Consumer Information and SafetySpecifications Installation InstructionsPlumbing Connections Below Pool InstallationValves Manual BY-PASSReversing Headers Water ConnectionsReversible Inlet/Outlet Connection, cont’d Sediment Traps GAS Line InstallationsGAS Connections Pipe Sizing for GAS Line Connections GAS Pipe SizingGAS Pressure Requirements Testing GAS PressureIndoor Venting General Requirements Outdoor Shelter Installation Canada Indoor Installation USA onlyFits ALL Models Combustion AIR SupplyVent Adaptors Section Outdoor Vent KIT Outdoor Installation Venting Guidelines Side ViewElectrical Connections Electrical Rating 60 Hz 120 / 240 Volts AC, single phaseVolts AC MiniMax NT TSI/DDTC Wiring Diagram Wiring DIAGRAM-NT STD & TSI with DdtcMinimax NT HSI Electronic Ignition LIGHTING/OPERATION Basic System OperationVacuum AIR Pressure FAN Switch Safety ControlsWater Pressure Switch Thermal FuseHigh Limits Heat ModeOperation of Ignition Module Failure to Light the BURNER-LOCK OUTSystem Indicator Lights Digital Display Temperature Controller DdtcSection IV. Operation SET UP Temperature Setting Troubleshooting Ddtc Troubleshooting InstructionService CHECKS-IGNITION Module Troubleshooting GeneralEnergy Saving Tips Maintenance InstructionWinter Operation Spring and Fall OperationPool and SPA Water Chemical BalanceReplacement Parts NT STD & TSI w/DDTC Réf Rev. G Rév. G Rev. G Rév. G Réf Pentair Pool Products, Inc Chauffe-eau pour piscine et spa MiniMax NT Guide Dinstallation ET DE FonctionnementTable des matières Information Pour Lidentification DU CHAUFFE-EAU Information Pour Lidentification DU CHAUFFE-EAUGarantie Consignes ImportantesConformité AUX Codes Mise EN GardeSpécifications Consignes dinstallationsDérivation Manuelle Raccords DE PlomberieSoupapes Collecteurs réversibles Raccordements DES Conduites DeauRaccords dentrée et de sortie réversibles, suite Collecteurs DE Sédiment Installations DE LA Conduite DE GAZRaccordement DES Conduites DE GAZ Mesure DES Tuyaux Pour Raccords D’ARRIVÉE DE GAZ Dimension DES Tuyaux DE GAZExigences Pour LA Pression DE GAZ Vérification DE LA Pression DE GAZVentilation Intérieur Exigences Générales Installation Intérieure États-Unis Uniquement Convient À Tous LES Modèles Admission Dair DE CombustionAdaptateurs Daération ApprovisionnementdAir Terminaison de la ventilation Ensemble DE Ventilation Pour LextérieurClassement électrique 60 Hz 120/240 Volts c.a. monophasé Raccordements ÉlectriquesVolts CA Réf Rev. G Rév Fonctionnement Générale DU Système Consignes de FonctionnementCommutateur Ventilateur DE Pression DU Vide Dair Contrôles DE SécuritéCommutateur DE Pression Deau Fusible ThermiqueHautes Limites Mode ChaleurVerrouillage EN CAS Déchec Dallumage Échec DE LA Flamme RallumageTémoins Indicateurs DU Système Thermostat À Affichage NumériqueSection IV. Fonctionnement Réglage DU Thermostat Réglage DE LA Temperature Dépannage Thermostat a Affichage Numerique Consignes DE DépannageVerifications Dentretien Module Dallumage Consignes DE DépannageSoupape DE Surpression Conseils Pour Économies DénergieFonctionnement EN Hiver Fonctionnement AU Printemps ET EN AutomneEAU DE Piscine ET DE SPA Équilibre Chimique DE LeauFORPour Modèle STD Réf Rev. G Rév. G Rev. G Rév. G Réf Veuillez Concerver CE Guide Dinstruction

200 specifications

The Pentair 200 is a sophisticated pool and spa control system designed to offer unmatched convenience, efficiency, and safety for users looking to enhance their aquatic experience. With cutting-edge technologies and a user-friendly interface, the Pentair 200 stands out as a leading solution in the pool management industry.

One of the main features of the Pentair 200 is its advanced automation capabilities. It allows users to control various aspects of their pool and spa, including lighting, heating, and filtration, all from a single control panel or a mobile app. This automation not only enhances usability but also ensures optimal performance, significantly reducing energy consumption compared to manual systems.

The integration with smart technology is another hallmark of the Pentair 200. Users can access the system remotely using their smartphones or tablets, allowing them to manage their pool settings from anywhere. This feature is particularly beneficial for those who may want to ensure their pool is ready for a gathering or simply wish to make adjustments while away from home.

The Pentair 200 is also designed with safety features in mind. It includes multiple protection mechanisms to prevent overheating and ensure regular operational safety, contributing to peace of mind for pool owners. Moreover, the easy-to-understand interface makes programming the system a breeze, even for those who may not be technologically inclined.

Efficiency is paramount in pool management, and the Pentair 200 excels in this area with energy-efficient technologies. Its variable-speed pump capabilities optimize energy usage depending on the specific needs of the pool, thereby resulting in lower utility bills and a reduced environmental impact.

Another notable characteristic is the system's durability and reliability. Constructed with high-quality materials and backed by Pentair's reputation in the industry, the 200 model is built to withstand various environmental conditions and provide consistent performance over time.

In summary, the Pentair 200 is a cutting-edge pool control system that enhances convenience, safety, and energy efficiency. Its advanced automation and smart technology integration make it a standout choice for modern pool owners. With the ability to manage their aquatic environments effectively and efficiently, users can enjoy their pools and spas with greater peace of mind.