Pentair 200 installation manual Reversible Inlet/Outlet Connection, cont’d

Page 9

Section III. Installation

9

 

 

Reversible Inlet/Outlet Connection, cont’d.

On the MiniMax NT Series heater there is insulation installed by the factory on the return head side of the heaters. This insulation is there so that if the heads are reversed in the field, during initial installation of the heater, the high limits will be insulated from the heat radiating from the flue collector.

6.Return head in position before removal. This view shows the insulation installed by the factory. Remove the 8 bolts holding the return head in place.

7.When heads are removed, replace the heat exchanger tube seal gaskets.

8.Exchange the inlet/outlet header with the return header. Lift the insulation to allow the main head to be installed. Align header with the heat exchanger. When head is placed into position, release the insulation; it will now shield the high limits from the heat produced by the flue collector. Install header bolts, and tighten snugly by hand. (This will help avoid cross threading.) When tightening, use a cross pattern starting from the center of the header. DO NOT over tighten.

9.Install the temperature sensing probe by passing the wires through the hole provided on the left side of the brace panel. Route wires through the support bracket.

10.Reconnect all the high limit wires and the pressure switch wiring, routing the wires through the same hole as the thermostat sensor wires.

11.Pump and bleed system to check the head for leaks.

12.Reinstall the two large inspection plates on the appropriate side.

Remember: The inlet and outlet markings

on the header are still correct.

Do not plumb the heater backwards.

Rev. G • Rév. G 5-27-04

P/N • Réf. 472090

Page 8 Page 10
Image 9
Page 8 Page 10
Contents MiniMax NT Pool & Spa Heaters Table of Contents Heater Identification Information HIN Heater Identification InformationImportant Notices Warranty InformationCode Requirements Consumer Information and SafetySpecifications Installation InstructionsPlumbing Connections Below Pool InstallationValves Manual BY-PASSReversing Headers Water ConnectionsReversible Inlet/Outlet Connection, cont’d GAS Line Installations GAS ConnectionsSediment Traps Pipe Sizing for GAS Line Connections GAS Pipe SizingGAS Pressure Requirements Testing GAS PressureIndoor Venting General Requirements Outdoor Shelter Installation Canada Indoor Installation USA onlyCombustion AIR Supply Vent AdaptorsFits ALL Models Section Outdoor Vent KIT Outdoor Installation Venting Guidelines Side ViewElectrical Connections Electrical Rating 60 Hz 120 / 240 Volts AC, single phaseVolts AC MiniMax NT TSI/DDTC Wiring Diagram Wiring DIAGRAM-NT STD & TSI with DdtcMinimax NT HSI Electronic Ignition LIGHTING/OPERATION Basic System OperationVacuum AIR Pressure FAN Switch Safety ControlsWater Pressure Switch Thermal FuseHigh Limits Heat ModeOperation of Ignition Module Failure to Light the BURNER-LOCK OUTSystem Indicator Lights Digital Display Temperature Controller DdtcSection IV. Operation SET UP Temperature Setting Troubleshooting Ddtc Troubleshooting InstructionService CHECKS-IGNITION Module Troubleshooting GeneralEnergy Saving Tips Maintenance InstructionWinter Operation Spring and Fall OperationPool and SPA Water Chemical BalanceReplacement Parts NT STD & TSI w/DDTC Réf Rev. G Rév. G Rev. G Rév. G Réf Pentair Pool Products, Inc Chauffe-eau pour piscine et spa MiniMax NT Guide Dinstallation ET DE FonctionnementTable des matières Information Pour Lidentification DU CHAUFFE-EAU Information Pour Lidentification DU CHAUFFE-EAUGarantie Consignes ImportantesConformité AUX Codes Mise EN GardeSpécifications Consignes dinstallationsRaccords DE Plomberie SoupapesDérivation Manuelle Collecteurs réversibles Raccordements DES Conduites DeauRaccords dentrée et de sortie réversibles, suite Installations DE LA Conduite DE GAZ Raccordement DES Conduites DE GAZCollecteurs DE Sédiment Mesure DES Tuyaux Pour Raccords D’ARRIVÉE DE GAZ Dimension DES Tuyaux DE GAZExigences Pour LA Pression DE GAZ Vérification DE LA Pression DE GAZVentilation Intérieur Exigences Générales Installation Intérieure États-Unis Uniquement Admission Dair DE Combustion Adaptateurs DaérationConvient À Tous LES Modèles ApprovisionnementdAir Terminaison de la ventilation Ensemble DE Ventilation Pour LextérieurClassement électrique 60 Hz 120/240 Volts c.a. monophasé Raccordements ÉlectriquesVolts CA Réf Rev. G Rév Fonctionnement Générale DU Système Consignes de FonctionnementCommutateur Ventilateur DE Pression DU Vide Dair Contrôles DE SécuritéCommutateur DE Pression Deau Fusible ThermiqueHautes Limites Mode ChaleurVerrouillage EN CAS Déchec Dallumage Échec DE LA Flamme RallumageTémoins Indicateurs DU Système Thermostat À Affichage NumériqueSection IV. Fonctionnement Réglage DU Thermostat Réglage DE LA Temperature Dépannage Thermostat a Affichage Numerique Consignes DE DépannageVerifications Dentretien Module Dallumage Consignes DE DépannageSoupape DE Surpression Conseils Pour Économies DénergieFonctionnement EN Hiver Fonctionnement AU Printemps ET EN AutomneEAU DE Piscine ET DE SPA Équilibre Chimique DE LeauFORPour Modèle STD Réf Rev. G Rév. G Rev. G Rév. G Réf Veuillez Concerver CE Guide Dinstruction

200 specifications

The Pentair 200 is a sophisticated pool and spa control system designed to offer unmatched convenience, efficiency, and safety for users looking to enhance their aquatic experience. With cutting-edge technologies and a user-friendly interface, the Pentair 200 stands out as a leading solution in the pool management industry.

One of the main features of the Pentair 200 is its advanced automation capabilities. It allows users to control various aspects of their pool and spa, including lighting, heating, and filtration, all from a single control panel or a mobile app. This automation not only enhances usability but also ensures optimal performance, significantly reducing energy consumption compared to manual systems.

The integration with smart technology is another hallmark of the Pentair 200. Users can access the system remotely using their smartphones or tablets, allowing them to manage their pool settings from anywhere. This feature is particularly beneficial for those who may want to ensure their pool is ready for a gathering or simply wish to make adjustments while away from home.

The Pentair 200 is also designed with safety features in mind. It includes multiple protection mechanisms to prevent overheating and ensure regular operational safety, contributing to peace of mind for pool owners. Moreover, the easy-to-understand interface makes programming the system a breeze, even for those who may not be technologically inclined.

Efficiency is paramount in pool management, and the Pentair 200 excels in this area with energy-efficient technologies. Its variable-speed pump capabilities optimize energy usage depending on the specific needs of the pool, thereby resulting in lower utility bills and a reduced environmental impact.

Another notable characteristic is the system's durability and reliability. Constructed with high-quality materials and backed by Pentair's reputation in the industry, the 200 model is built to withstand various environmental conditions and provide consistent performance over time.

In summary, the Pentair 200 is a cutting-edge pool control system that enhances convenience, safety, and energy efficiency. Its advanced automation and smart technology integration make it a standout choice for modern pool owners. With the ability to manage their aquatic environments effectively and efficiently, users can enjoy their pools and spas with greater peace of mind.
Top Page Image Contents