Zenoah BCZ2600DL manual MA8, Cylinder Intake air cooling vent back

Page 51

 

English

 

Français

 

 

9. Maintenace

9. Entretien

 

 

 

 

 

MA7(1)

(2)

MA8

engine to catch on fire. Always make sure that the muffler is clean and free of wood chips, leaves, and other waste before use.

•Check the intake air cooling vent and the area around the cylinder cooling fins after every 25 hours of use for blockage, and remove any waste which has attached itself to the brushcutter. Note that it is necessary to remove the engine cover shown in (MA7) in order to be able to view the upper part of the cylinder.

IMPORTANT

•If waste gets stuck and causes blockage around the intake air cooling vent or between the cylinder fins, it may cause the engine to overheat, and that in turn may cause mechanical failure on the part of the brushcutter. (MA7)

(1)cylinder

(2)intake air cooling vent (back)

■PROCEDURES TO BE PERFORMED AFTER EVERY 100 HOURS OF USE

1.Remove the muffler, insert a screwdriver into the vent, and wipe away any carbon buildup. Wipe away any carbon buildup on the muffler exhaust vent and cylinder exhaust port at the same time.

2.Tighten all screws, bolts, and fittings.

3.Check to see if any oil or grease has worked its way in between the clutch lining and drum, and if it has wipe it away using oil-free, lead-free gasoline.

silencieux peut surchauffer et le moteur peut prendre feu. Toujours vérifier que le silencieux est propre et débarrassé des copeaux, feuilles mortes et autres débris avant d’utiliser la machine.

•Vérifier l’ouïe d’entrée d’air de refroidissement et la zone des ailettes autour du cylindre toutes les 25 heures de fonctionnement et retirer tout bourrage de détritus. Prendre note qu’il est nécessaire de démonter le capot moteur (MA7) pour accéder à la partie supérieure du cylindre.

IMPORTANT

•Si des détritus se coincent et bouchent la zone aux alentours de l’ouïe d’entrée d’air de refroidissement, le moteur risque de chauffer et provoquer une grave panne mécanique. (MA7)

(1)cylindre

(2)Ouïe d’entrée d’air de refroidissement (arrière)

■ PROCEDURE A EFFECTUER

TOUTES LES 100 HEURES D’UTILISATION

1.Démonter le silencieux et insérer un tournevis dans la fente pour retirer tous les dépôts éventuels de calamine. Retirer également tous les autres dépôts sur le silencieux.

2.Serrer les vis, boulons et fixations.

3.Vérifier si de l’huile ou de la graisse s’est introduite entre les mâchoires et le tambour d’embrayage ; si s’est le cas, les nettoyer à l’essence sans plomb.

52

Page 50 Page 52
Image 51
Page 50 Page 52
Contents BCZ2600DL English Français Deutsch Italiano Español Riesgo DE Daño Auditivo Risk of Damaging HearingHörschaden Risiko Rischio DI Danno UditivoContents Tables des matieres Inhalt Indice Contenido Parts location Emplacement des pieces Parachispas BCZ2600DL SpecificationsSpecifications are subject to change without notice Fiche techniqueStandardzubehör Technische DatenDati tecnici EspecificaciohesMachine Sur la machine Symbols on the machine Symboles utilises sur la MachineEmplacement Etiquettes d’avertissementPosizione Posición Position PosizioneEstrangulador Conditions DE Travail For safe operation Consignes de securiteWorking Condition Working CircumstanceCircostanze Lavorative ArbeitsbedingungArbeitsumstand Condizioni LavorativeLA Machine Working PlanBefore Starting the Engine Plan DE TravailPlan DE Trabajo ArbeitsplanBeim Planen der Arbeitseinsätze Piano DI LavoroDemarrage DU Moteur Starting the EngineArranque DEL Motor Avvertimento AdvertenciaDEN Motor Starten Accensione DEL MotoreUtilisation DE LA Machine Using the ProductMaintenance If Someone ComesUtilizzo DEL Prodotto Benutzung DES ProduktesFalls Sich Jemand Nähert WartungKomatsu Zenoah Check okHandling Fuel Refill after cooling the engineHandhabung DES Kraftstoffs Maneggio DEL CarburanteManipulación DEL Combustible Transport TransportationMotore si è raffreddato TrasportoTransporte Set up Assemblage SE1SE2 SE3 SE4 SE5 Zusammenbau Impostazione Montaje SE6 Zusammenbau Impostazione Montaje HOW to MIX Fuel Fuel CarburantComment Effectuer LE Melange DE Carburant ? Cómo Mezclar EL Combustible Kraftstoff Carburante CombustibleMischen VON Kraftstoff PER IL Miscelazione DEL CarburantePour Prolonger LA Duree DE VIE DU MOTEUR, NE PAS Utiliser Fuel CarburantFueling the Unit Remplissage DU Reservoir For Your Engine LIFE, AvoidWegen DER Lebensdauer Ihres GERÄTES, Folgendes Vermeiden Einfüllen VON Kraftstoff DAS GerätRiempimento DEL Serbatoio DEL Carburante Cómo Cargar Combustible EN LA UnidadStarting Engine Mise EN Marche DU Moteur Operation FonctionnementOP1 OP3 OP4Starten DES Motors Avviamento DEL Motore Arranque DEL Motor Betrieb Funzionamento UsoOperation Fonctionnement OP5OP6 Regolazione Della Velocità NEL Funzionamento AL Minimo OP6 Einstellen DrosselkabelEinstellen DES Leerlaufs OP6 Regolazione Cavo DEL GASOP8 OP9 OP7Betrieb Funzionamento Uso Controle DES Coups DE Recul Controlling Blade BounceHow you can reduce the chance of kick out Avoid feeding the blade too rapidlySchneidblattaufprall Steuern Controllo DEL Rimbalzo Della LamaControl DEL Contragolpe DE LA Hoja Coupe DE Gazon OU D’HERBES Line Head UsageTrimming Grass and Weeds Utilisation DE LA Tete DE Coupe a FILPER Tagliare L’ERBA E Erbaccia Verwendung DES SchnurkopfesGras UND Unkraut Schneiden Utilizzo Dello Strumento DA Taglio a CordaReglage DE LA Longeur DU FIL DE Coupe Adjusting the Line LengthAjuste DE LA Longitud DE LA Línea Einstellung DER SchnurlängeGradi verso la direzione dell’operazione. OP11 Regolazione Della Lunghezza Della CordaTableau D’ENTRETIEN Maintenance ChartMaintenace EntretienWartung ManutenzioneMantenimiento Maintenace Entretien MA1MA2 MA3 MA4 Wichtig Importante Wartung Manutenzione MantenimientoSilencieux Tightening TorqueMuffler Couple DE SerrageMarmitta AnzugsmomentDämpfer Torsione DI SerraggioCylinder Intake air cooling vent back Procedures to be Performed After Every 100 Hours of USEProcedure a Effectuer Toutes LES 100 Heures D’UTILISATION MA8Procedure DA Effettuare Ogni 100 ORE DI Utilizzo Alle 100 Betriebsstunden Auszuführende WartungsarbeitenProcedimientos a Realizar Cada 100 Horas DE USO Storage Rangement Lagerung Immagazzinaggio Almacenamiento Verification Causes Probables Action Troubleshooting guideGuide de localisation des pannes Check Probable Causes Action11. Guía de localización y solución de problemas FehlersucheLocalizzazione dei guasti Limited warranty Garantie limitée Garantiebestimmungen Garanzia limitata Garantía limitada

BCZ2600DL specifications

The Zenoah BCZ2600DL is a high-performance brush cutter designed for both professional landscapers and dedicated home users. This powerful tool combines efficiency with ergonomic design, making yard work not only effective but also manageable and comfortable. Its robust engine, advanced features, and user-friendly interface all contribute to its stature as a leading choice in the market.

At the heart of the BCZ2600DL lies a reliable 25.4cc, two-stroke engine that delivers impressive power while remaining lightweight. This engine is engineered for fuel efficiency, reducing the environmental impact and allowing users to work longer without frequent refueling. The tool is designed for easy starting, thanks to a convenient primer bulb and an advanced ignition system that ensures reliable performance in various conditions.

One of the standout features of the BCZ2600DL is its unique Anti-Vibration System. This technology minimizes vibrations during operation, significantly reducing user fatigue and allowing for longer work sessions without discomfort. The ergonomic handle design further enhances comfort, giving users better control and reducing strain on the arms and shoulders.

The brush cutter is equipped with a dual-line bump feed head that allows for quick and easy line advancement, making it ideal for trimming grass and clearing weeds. The 26.2cc engine provides enough power to tackle tougher vegetation, including brush and dense undergrowth, making it versatile for various landscaping projects. Additionally, the heavy-duty cutting attachment ensures durability and longevity, even under rigorous usage.

Another remarkable characteristic of the Zenoah BCZ2600DL is its lightweight construction. Weighing in at around 10 pounds, it is easy to maneuver, making it perfect for both professional landscapers who need to cover large areas and homeowners tackling smaller jobs. The detachable shaft allows for compact storage and easy transport, another plus for users on the go.

In terms of safety, Zenoah has integrated several features to protect users while working. The throttle trigger is equipped with a safety lock, preventing accidental starts, and the exhaust system is designed to minimize emissions for a cleaner environment.

In summary, the Zenoah BCZ2600DL brush cutter stands out in the outdoor power equipment market due to its combination of a powerful yet fuel-efficient engine, comfort-driven designs, advanced technologies, and user-friendly features. Whether you're trimming your backyard or tackling a more extensive landscaping job, the BCZ2600DL is built to meet and exceed expectations.
Top Page Image Contents