Zenoah BCZ2600DL Fuel Carburant, HOW to MIX Fuel, Comment Effectuer LE Melange DE Carburant ?

Page 29

 

English

 

Français

 

 

7. Fuel

 

7. Carburant

 

 

 

 

 

WARNING

AVERTISSEMENT

•Keep open flames away from the area where fuel is handled or stored.

•Mix and store fuel only in an approved gasoline container.

Mix a regular grade gasoline (leaded or unleaded, alcohol-free) and a quality- proven motor oil for air cooled 2 cycle engines.

25 : 1 Mix Chart

Gasoline (liters)

1

2

3

4

5

2-cycle oil (ml.)

40

80

120

160

200

•Préparer et conserver le mélange loin de toute flamme.

•Préparer et conserver le mélange dans un bidon prévu pour contenir de l'essence.

Mélanger de l'essence ordinaire (avec ou sans plomb, mais sans alcool) à une huile de bonne qualité pour moteur 2-temps à refroidissement par air.

Table de métange au rapport 25/1 (4%)

Essence (litres)

1

2 3

4

5

Huile moteur 2-temps

(millilitres)

40 80 120 160 200

Recommended mixing ratio:

Condition

Gasoline : Oil

Up to 20 hours use

20 : 1

After 20 hours use

25 : 1

NOTE

Most engine troubles are caused, directly or indirectly, by the fuel used on the machine. Take special care not to mix a motor oil for 4 cycle engines.

■HOW TO MIX FUEL

1.Measure out the quantities of gasoline and oil to be mixed.

2.Put some of the gasoline into a clean, approved fuel container.

3.Pour in all of the oil and agitate well.

4.Pour in the rest of gasoline and agitate again for at least one minute.

5.Put a clear indication on the outside of the container to avoid mixing up with gasoline or other containers.

6.Indicate the contents on outside of container for easy identification.

Proportions du mélange:

Période

Rapport Essence/Huile

Au cours de 20 premières

20/1 (5%)

heure de marche

 

Après la 20 ème heure

25/1 (4%)

REMARQUE

La plupart des ennuis de moteur sont directement ou indirectement imputables à la qualité du carburant utilisé. Ne jamais préparer le mélange avec une huile pour moteur 4-temps.

■ COMMENT EFFECTUER LE

MELANGE DE CARBURANT ?

1.Mesurer les quantités d’essence et d’huile devant être mélangées.

2.Mettre l’essence dans un conteneur propre et prévu pour cet usage.

3.Verser la moitié de la quantité d’huile et bien agiter le conteneur.

4.Verser le reste d’huile et agiter de nouveau le conteneur pendant au moins une minute.

5.Marquer le conteneur de manière à éviter de le mélanger à de l’essenceou à d’autres conteneurs.

6.ndiquer le contenu à l’extérieur du conteneur pour faciliter son repérage.

30

Page 28 Page 30
Image 29
Page 28 Page 30
Contents BCZ2600DL English Français Deutsch Italiano Español Hörschaden Risiko Risk of Damaging HearingRischio DI Danno Uditivo Riesgo DE Daño AuditivoContents Tables des matieres Inhalt Indice Contenido Parts location Emplacement des pieces Parachispas Specifications are subject to change without notice SpecificationsFiche technique BCZ2600DLDati tecnici Technische DatenEspecificaciohes StandardzubehörEmplacement Symbols on the machine Symboles utilises sur la MachineEtiquettes d’avertissement Machine Sur la machineEstrangulador Posizione Posición PositionPosizione Working Condition For safe operation Consignes de securiteWorking Circumstance Conditions DE TravailArbeitsumstand ArbeitsbedingungCondizioni Lavorative Circostanze LavorativeBefore Starting the Engine Working PlanPlan DE Travail LA MachineBeim Planen der Arbeitseinsätze ArbeitsplanPiano DI Lavoro Plan DE TrabajoDemarrage DU Moteur Starting the EngineDEN Motor Starten Avvertimento AdvertenciaAccensione DEL Motore Arranque DEL MotorMaintenance Using the ProductIf Someone Comes Utilisation DE LA MachineFalls Sich Jemand Nähert Benutzung DES ProduktesWartung Utilizzo DEL ProdottoHandling Fuel Check okRefill after cooling the engine Komatsu ZenoahManipulación DEL Combustible Handhabung DES KraftstoffsManeggio DEL Carburante Transport TransportationTransporte Motore si è raffreddatoTrasporto SE2 SE3 SE4 SE5 Set up AssemblageSE1 Zusammenbau Impostazione Montaje SE6 Zusammenbau Impostazione Montaje Comment Effectuer LE Melange DE Carburant ? HOW to MIX FuelFuel Carburant Mischen VON Kraftstoff Kraftstoff Carburante CombustiblePER IL Miscelazione DEL Carburante Cómo Mezclar EL CombustibleFueling the Unit Remplissage DU Reservoir Fuel CarburantFor Your Engine LIFE, Avoid Pour Prolonger LA Duree DE VIE DU MOTEUR, NE PAS UtiliserRiempimento DEL Serbatoio DEL Carburante Einfüllen VON Kraftstoff DAS GerätCómo Cargar Combustible EN LA Unidad Wegen DER Lebensdauer Ihres GERÄTES, Folgendes VermeidenOP1 Operation FonctionnementOP3 OP4 Starting Engine Mise EN Marche DU MoteurStarten DES Motors Avviamento DEL Motore Arranque DEL Motor Betrieb Funzionamento UsoOP6 Operation FonctionnementOP5 Einstellen DES Leerlaufs OP6 Einstellen DrosselkabelRegolazione Cavo DEL GAS Regolazione Della Velocità NEL Funzionamento AL Minimo OP6OP8 OP9 OP7Betrieb Funzionamento Uso How you can reduce the chance of kick out Controlling Blade BounceAvoid feeding the blade too rapidly Controle DES Coups DE ReculControl DEL Contragolpe DE LA Hoja Schneidblattaufprall SteuernControllo DEL Rimbalzo Della Lama Trimming Grass and Weeds Line Head UsageUtilisation DE LA Tete DE Coupe a FIL Coupe DE Gazon OU D’HERBESGras UND Unkraut Schneiden Verwendung DES SchnurkopfesUtilizzo Dello Strumento DA Taglio a Corda PER Tagliare L’ERBA E ErbacciaReglage DE LA Longeur DU FIL DE Coupe Adjusting the Line LengthGradi verso la direzione dell’operazione. OP11 Einstellung DER SchnurlängeRegolazione Della Lunghezza Della Corda Ajuste DE LA Longitud DE LA LíneaMaintenace Maintenance ChartEntretien Tableau D’ENTRETIENMantenimiento WartungManutenzione MA2 MA3 MA4 Maintenace EntretienMA1 Wichtig Importante Wartung Manutenzione MantenimientoMuffler Tightening TorqueCouple DE Serrage SilencieuxDämpfer AnzugsmomentTorsione DI Serraggio MarmittaProcedure a Effectuer Toutes LES 100 Heures D’UTILISATION Procedures to be Performed After Every 100 Hours of USEMA8 Cylinder Intake air cooling vent backProcedimientos a Realizar Cada 100 Horas DE USO Procedure DA Effettuare Ogni 100 ORE DI UtilizzoAlle 100 Betriebsstunden Auszuführende Wartungsarbeiten Storage Rangement Lagerung Immagazzinaggio Almacenamiento Guide de localisation des pannes Troubleshooting guideCheck Probable Causes Action Verification Causes Probables ActionLocalizzazione dei guasti 11. Guía de localización y solución de problemasFehlersuche Limited warranty Garantie limitée Garantiebestimmungen Garanzia limitata Garantía limitada

BCZ2600DL specifications

The Zenoah BCZ2600DL is a high-performance brush cutter designed for both professional landscapers and dedicated home users. This powerful tool combines efficiency with ergonomic design, making yard work not only effective but also manageable and comfortable. Its robust engine, advanced features, and user-friendly interface all contribute to its stature as a leading choice in the market.

At the heart of the BCZ2600DL lies a reliable 25.4cc, two-stroke engine that delivers impressive power while remaining lightweight. This engine is engineered for fuel efficiency, reducing the environmental impact and allowing users to work longer without frequent refueling. The tool is designed for easy starting, thanks to a convenient primer bulb and an advanced ignition system that ensures reliable performance in various conditions.

One of the standout features of the BCZ2600DL is its unique Anti-Vibration System. This technology minimizes vibrations during operation, significantly reducing user fatigue and allowing for longer work sessions without discomfort. The ergonomic handle design further enhances comfort, giving users better control and reducing strain on the arms and shoulders.

The brush cutter is equipped with a dual-line bump feed head that allows for quick and easy line advancement, making it ideal for trimming grass and clearing weeds. The 26.2cc engine provides enough power to tackle tougher vegetation, including brush and dense undergrowth, making it versatile for various landscaping projects. Additionally, the heavy-duty cutting attachment ensures durability and longevity, even under rigorous usage.

Another remarkable characteristic of the Zenoah BCZ2600DL is its lightweight construction. Weighing in at around 10 pounds, it is easy to maneuver, making it perfect for both professional landscapers who need to cover large areas and homeowners tackling smaller jobs. The detachable shaft allows for compact storage and easy transport, another plus for users on the go.

In terms of safety, Zenoah has integrated several features to protect users while working. The throttle trigger is equipped with a safety lock, preventing accidental starts, and the exhaust system is designed to minimize emissions for a cleaner environment.

In summary, the Zenoah BCZ2600DL brush cutter stands out in the outdoor power equipment market due to its combination of a powerful yet fuel-efficient engine, comfort-driven designs, advanced technologies, and user-friendly features. Whether you're trimming your backyard or tackling a more extensive landscaping job, the BCZ2600DL is built to meet and exceed expectations.
Top Page Image Contents