Briggs & Stratton 030242-0 manual Air Cooling System, Check Valve Clearance, Carburetor Adjustment

Page 19

1.To remove muffler heat shield (A) from muffler (B), remove four screws that connect guard to muffler bracket.

C

A

B

2.Remove four screws that attach spark arrester screen (C).

3.Inspect screen and obtain a replacement if torn, perforated or otherwise damaged. DO NOT use a defective screen. If screen is not damaged, clean it with commercial solvent.

4.Reattach screen and muffler guard.

Air Cooling System

Over time debris may accumulate in cylinder cooling fins and cannot be observed without partial engine disassembly. For this reason, we recommend you have an authorized service dealer clean the cooling system (D) per recommended intervals (see Maintenance Schedule in beginning of Maintenance section). Equally important is to keep top of engine free from debris. See Clean Debris.

D

Check Valve Clearance

Regular valve clearance check and adjustment will improve performance and extend engine life. This procedure cannot be done without partial engine disassembly and the use of special tools. For this reason we recommend that you have an authorized service dealer check and adjust valve clearance at recommended intervals (see Maintenance Schedule in the Maintenance section).

Carburetor Adjustment

The carburetor on this engine is low emission. It is equipped with a non-adjustable idle mixture valve. Top speed has been set at the factory. If adjustment is required, see an authorized service dealer.

CAUTION

Excessively high operating speeds increase risk of injury and damage to generator.

Excessively low speeds impose a heavy load.

•DO NOT tamper with governed speed. Generator supplies correct rated frequency and voltage when running at governed speed.

•DO NOT modify generator in any way.

19

Image 19

Contents Operator’s Manual Date Purchased Where to Find UsGenerator EngineTable of Contents Hazard Symbols and Meanings Operator SafetySafety Rules Safety alert symbol is used with a signal wordBroken bones, fractures, bruises, or sprains could result Engine exhaust from this product containsContact with muffler area can result in serious burns When Testing for Engine SparkUnintentional sparking can result in fire or electric shock Unpack Generator AssemblyInstall Wheel Kit Install the wheel kit as followsAdd Engine Oil Attach Negative Battery CableAdd Fuel Special Requirements Connecting to a Building’s Electrical SystemSystem Ground Generator LocationItems Not Shown Features and ControlsUsed to supply electrical power for the operation Volt AC, 20 Amp, Duplex Receptacles May beVolt AC, 20 Amp, Duplex Receptacles Cord Sets and ReceptaclesNema L14-30 120/240 Volt AC, 30 Amp, Locking ReceptacleBattery Float Charger Starting the Engine OperationStopping the Engine Connecting Electrical LoadsMove fuel valve to Off position Wattage Reference Guide Don’t Overload GeneratorMaintenance Schedule MaintenanceGenerator Maintenance Engine Maintenance Battery MaintenanceOil Service Spark Arrester Service Air CleanerService Spark Plug Install spark plug and tighten firmlyAir Cooling System Carburetor AdjustmentCheck Valve Clearance Storage Troubleshooting Owner’s Warranty Responsibilities Emissions Control System WarrantyWarranties Emission Information MaintenanceClaims and Coverage Exclusions Limited Warranty Page Common Service Parts Product Specifications800 Manual del Operario Fecha de compra Dónde encontrarnosGenerador MotorControles y características Resolución de problemas GarantíasSeguridad de operario MontajeSímbolos de peligro y sus significados Seguridad de operarioDescripción del equipo Reglas de seguridadCuando Transporte O Repare EL Equipo Cuando Anada Combustible O Vacíe EL DepósitoCuando Ponga EN Funcionamiento EL Equipo Cuando Opere EL EquipoCuando Pruebe LA Bujía DEL Motor Cuando Ajuste O Haga Reparaciones a SU Máquina GeneradorEl generador se entrega con MontajeDesembalaje del generador Instale el juego de ruedasAgregue combustible Agregar aceite al motorConecte el cable negativo de la batería Requisitos especiales Tierra del sistemaConexión al sistema eléctrico de un edificio Ubicación del generadorAmperios, monofásica de 60 Hz Controles y característicasAmps o mayores Juegos de cordones y enchufes conectoresTomas eléctricas dobles de 120 V CA y 20 a Dispositivo de seguridad de 120/240 V, 30 aCargador de flotación de la batería Encienda el motor OperandoSi el motor no arranca, repita los pasos desde 5 hasta Gire la válvula de combustible blanca hasta la posición Off Conexión de cargas eléctricasParada del motor El motor podría petardear, incendiarse o dañarseControl de la energía No sobrecargar el generadorCapacidad EjemploPlan de mantenimiento MantenimientoMantenimiento del generador Comprobación del nivel de aceite Mantenimiento de la bateríaMantenimiento del motor Aceite Recomendaciones sobre el aceiteServicio del depurador de aire Cambio de aceite del motorServicio del bujía Comprobación de holgura de la válvula Limpie la Pantalla ApagachispasLimpie e inspeccione el apagachispas de la siguiente manera Sistema de refrigeración de aireAlmacenamiento Problemo Causa Accion Resolución de problemasGarantía del sistema de control de emisiones GarantíasResponsabilidades de la garantía del propietario Información sobre emisiones Garantía Limitada Page Servicio común despide Especificaciones del producto