Briggs & Stratton 71013 manual Power Wiring Interconnections

Page 7

Power Wiring Interconnections

All wiring must be the proper size, properly supported and protected by conduit. All wiring should be done per applicable federal, state and local codes, standards and regulations.

Complete the following connections between the transfer switch, power management system and main breaker panel. Also see the Wiring Decal on page 8.

WARNING

Low voltage wire cannot be installed in same conduit as power voltage wiring.

•Failure to follow above warning could cause personal injury, damage and/or malfunction of equipment.

1.Set generator’s system switch to OFF position.

2.Set generator’s main circuit breaker to OFF (open) position.

3.Identify loads and their priorities (using list developed with owner) to be transferred to power management system in main breaker panel.

4.In main breaker panel, turn selected load circuit breakers to OFF position.

NOTICE

Improper installation can cause damage to the circuit boards and shorten their life. Installing circuit boards in live circuits will damage the board and is not a warranty condition. ALWAYS disconnect ALL sources of power prior to servicing.

•Remove all power prior to installing this power management system. Failure to do so could cause internal damage to the board when making electrical connections.

•Turn generator to OFF position.

•Turn off utility power to the home standby generator and transfer switch.

5. Connect “GND” lug to an approved ground.

NOTE: Assure grounding electrode conductor is connected and bonded per applicable federal, state and local codes, standards and regulations.

6.Using installer supplied 300VAC or greater wire and supplied 1/4” double male, single female lugs, connect generator 240VAC from transfer switch to relay board in power management system.

7.Unplug current transformers from control module in transfer switch.

 

Green LED’s

Relay Board

Control

Module

 

 

Test

 

Button

 

Transfer Switch

 

Connections

Load

 

Connection

 

Wireways

Air Conditioner

Relays

Generator

Air Conditioner

Connection

Connections

To Transfer Switch

Ground Lug

 

To Air Conditioners

 

5

Page 6 Page 8
Image 7
Page 6 Page 8
Contents 800 743-4115M-F 8-5 CT Call HelplineBRIGGSandSTRATTON.COM Power Management System Where to Find UsTable Of Contents Important Safety Instructions Owner Orientation Installer ResponsibilitiesIntroduction For the Home OwnerMounting Guidelines InstallationShipment Contents UnpackingPower Wiring Interconnections You must perform the following before operating the system System SetupControls Testing the Power Management SystemOperation Wiring Decal 240VAC Electrical Appliances Electrical Load Worksheet PriorityRelay Contacts MaintenanceWhen Calling the Factory SpecificationsProblem Cause Correction TroubleshootingSupplying power Description Illustrated Parts ListItems Not Illustrated Limited Warranty Reserved Llamada Línea Directa Manual de Instalación y del OperarioSistema de Gestión de Energía Dónde encontrarnosFecha de compra Mantenimiento MandosEspecificaciones Conserve estas instrucciones Responsabilidades del Instalador IntroduccionPara el Propietario Doméstico Orientación para el PropietarioInspección al Momento de la Entrega InstalacionDesempaque Pautas de MontajeInterconexiones de Cableado de Energía Configuración del Sistema Sistema Funcionamiento MandosPrueba del sistema de gestión de energía eléctrica Alambrar la calcomanía Hoja de trabajo de cargas eléctricas Especificaciones DimensionesMantenimiento Si Necesita Llamar a FábricaReparacion de Averias Problemo Causa AccionLos terminales Garantia 800 743-4115 M-F8-5 CT BRIGGSandSTRATTON.COM Guide dInstallation Et dUtilisationSystème de Gestion de L’alimentation Où nous trouverDate d’achat Entretien CommandesCaractéristiques Dépannage Garantie Instalación FonctionnementCommandesDirectives de sécurité importantes SécuritéDescription de lÉquipement Responsabilités de lInstallateurAu Propriétaire Résidentiel Conseils au PropriétaireVérification de la Livraison Consignes dinstallationSécurité Instalación Commandes DéballageSécurité Instalación Interconnexions du câblage dalimentationContrôleur dans le commutateur de transfert Commandes Fonctionnement Configuration du systèmeFonctionnement CommandesMise à lessai du système de gestion de lalimentation Décalcomanie dinstallation éléctrique Fiche technique de charge électrique Valeur nominale des EntretienSi vous Devez Communiquer avec lUsine CaractéristiquesDépannage Fonctionnement Entretien Garantie
Top Page Image Contents