Briggs & Stratton 71013 System Setup, You must perform the following before operating the system

Page 8

8.Cut two pin connector ends off of current transformer leads and discard. Strip wires and place in supplied wire connectors.

9.Using installer supplied 300VAC or greater wire, run wires from wire connectors to control module terminal block labeled “CT1A” through “CT2B” in power management system.

10.Using installer supplied 300VAC or greater wire, connect C (Common) and NO (Normally Open) terminals on terminal strip J9 of control module in transfer switch to control module terminal block labeled “TXSF” and “TXFG” in power management system.

Location of J9 Terminal Strip in Transfer Switch

11.Wire the air conditioner thermostat control wiring to the control module labeled “AC1A-AC2B” in power management system.

NOTE: AC1A and AC1B is for the priority 1 air conditioner. AC2A and AC2B is for the priority 2 air conditioner.

12.For 120VAC selected loads, remove wire from selected load circuit breaker.

13.Using installer supplied 300VAC or greater wire, connect selected load circuit breaker to terminal block at power management system labeled “CB/B1” for priority 1 load.

14.Using installer supplied 300VAC or greater wire and a wire nut, connect the selected load wire to terminal block in power management system labeled “RLY/B1” for priority 1 load.

15.Repeat steps 12 through 14 for all other 120VAC priorities using terminals “CB/C1” through “RLY/D2”.

16.For 240VAC selected loads, remove both wires from selected load circuit breaker and place in load side of installer supplied contactor.

17.Using installer supplied 300VAC or greater wire, connect circuit breaker to line side of contactor.

18.Using installer supplied 300VAC or greater wire, connect one pole of the circuit breaker to terminal block in power management system labeled “CB/B1” for a priority 1 load.

19.Using installer supplied 300VAC or greater wire, connect Neutral in main breaker panel to contactor coil.

20.Using installer supplied 300VAC or greater wire, connect contactor coil to terminal block in power management system labeled “RLY/B1” for a priority 1 load.

21.Repeat steps 16 through 20 for all other 240VAC priorities using terminals “CB/C1” through “RLY/D2”.

22.Tighten all wire connections/fasteners to proper torque. See inside power management system enclosure for proper torque values.

System Setup

You must perform the following before operating the system:

•Place the switch labeled “SW2” on the control module in the NG or LP position, whichever is appropriate for the installed home standby system.

 

SW2

 

 

SW3

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

•Place the switch labeled “SW3” on the control module to match the rating of the home standby system.

•In main breaker panel, turn selected load circuit breakers to the ON position.

IMPORTANT: After installation of the power management system is complete, turn on utility power to the home standby generator and transfer switch. Wait one minute before turning generator to AUTO.

6

BRIGGSandSTRATTON.COM

Page 7 Page 9
Image 8
Page 7 Page 9
Contents BRIGGSandSTRATTON.COM Call Helpline800 743-4115M-F 8-5 CT Where to Find Us Power Management SystemTable Of Contents Important Safety Instructions Installer Responsibilities IntroductionFor the Home Owner Owner OrientationInstallation Shipment ContentsUnpacking Mounting GuidelinesPower Wiring Interconnections System Setup You must perform the following before operating the systemOperation Testing the Power Management SystemControls Wiring Decal Electrical Load Worksheet Priority 240VAC Electrical AppliancesMaintenance When Calling the FactorySpecifications Relay ContactsSupplying power TroubleshootingProblem Cause Correction Items Not Illustrated Illustrated Parts ListDescription Limited Warranty Reserved Manual de Instalación y del Operario Llamada Línea DirectaFecha de compra Dónde encontrarnosSistema de Gestión de Energía Especificaciones MandosMantenimiento Conserve estas instrucciones Introduccion Para el Propietario DomésticoOrientación para el Propietario Responsabilidades del InstaladorInstalacion DesempaquePautas de Montaje Inspección al Momento de la EntregaInterconexiones de Cableado de Energía Configuración del Sistema Prueba del sistema de gestión de energía eléctrica MandosSistema Funcionamiento Alambrar la calcomanía Hoja de trabajo de cargas eléctricas Dimensiones MantenimientoSi Necesita Llamar a Fábrica EspecificacionesLos terminales Problemo Causa AccionReparacion de Averias Garantia Guide dInstallation Et dUtilisation 800 743-4115 M-F8-5 CT BRIGGSandSTRATTON.COMDate d’achat Où nous trouverSystème de Gestion de L’alimentation Caractéristiques CommandesEntretien Instalación FonctionnementCommandes Directives de sécurité importantesSécurité Dépannage GarantieResponsabilités de lInstallateur Au Propriétaire RésidentielConseils au Propriétaire Description de lÉquipementConsignes dinstallation Sécurité Instalación CommandesDéballage Vérification de la LivraisonContrôleur dans le commutateur de transfert Interconnexions du câblage dalimentationSécurité Instalación Configuration du système Commandes FonctionnementMise à lessai du système de gestion de lalimentation CommandesFonctionnement Décalcomanie dinstallation éléctrique Fiche technique de charge électrique Entretien Si vous Devez Communiquer avec lUsineCaractéristiques Valeur nominale desDépannage Garantie Fonctionnement Entretien

71013 specifications

The Briggs & Stratton 71013 is a highly regarded product in the realm of outdoor power equipment, specifically designed to offer reliable performance with a robust set of features. This model showcases the brand's commitment to quality engineering, making it an excellent choice for both residential and commercial applications.

One of the standout features of the Briggs & Stratton 71013 is its portable power generation capability. This model is equipped with a powerful engine that delivers ample wattage, making it suitable for various power needs, whether for camping trips, outdoor events, or backup for home appliances during outages. Thanks to its efficient fuel consumption, users can count on prolonged runtime, enhancing its practicality in emergency situations.

The 71013 utilizes advanced technology for ease of use. For instance, the unit often incorporates a convenient electric start option, allowing hassle-free starting even in cold weather conditions. The intuitive control panel is designed with user-friendliness in mind, enabling operators to monitor power output and manage usage easily.

In terms of durability, the Briggs & Stratton 71013 is designed to withstand the elements. Its rugged frame is crafted from high-quality materials, ensuring that it can endure rough handling and inclement weather. Additionally, the model features heavy-duty wheels for easy mobility across various terrains, making it a versatile option for users.

Maintenance has been simplified with the inclusion of user-friendly features. The engine's design allows for easy access to key components, making routine maintenance tasks straightforward. This focus on convenience extends to the air filter and oil replacement systems, which are user-friendly and ensure the longevity of the equipment.

Furthermore, safety features are integrated into the Briggs & Stratton 71013 to protect users and equipment alike. A built-in circuit breaker helps to prevent overloads, ensuring safe operation. The design also emphasizes low noise levels, making it suitable for residential areas without causing disturbances.

In summary, the Briggs & Stratton 71013 stands out with its powerful engine, portable design, user-friendly features, and robust safety measures. Whether for emergency power needs or outdoor activities, this model is engineered to deliver reliability and performance, solidifying its place as a trusted companion for power generation.
Top Page Image Contents