Sears 247.88355 operating instructions Chute Assembly, Auger Control

Page 11

ASSEMBLY

Chute Assembly

The distance snow is thrown can be adjusted by changing the angle of the chute assembly. To do so:

1.Stop the engine by removing the ignition key and loosen the plastic wing knob found on the left side of the chute assembly.

2.Pivot the chute upward or downward before retightening the wing knob. See Figure 8.

Auger Control

WARNING

Prior to operating your snow thrower, carefully read and follow all instructions below. Perform all adjustments to verify your snow thrower is operating safely and properly.

Check the adjustment of the auger control as follows:

1.When the auger control is released and in the disengaged “up” position, the cable should have very little slack. It should NOT be tight.

2.In a well-ventilated area, start the snow thrower engine. Refer

to Starting the Engine in the Operation section. Make sure the

throttle is set in the FAST position.

3.While standing in the operator’s position (behind the snow thrower), engage the auger.

4.Allow the auger to remain engaged for approximately ten (10) seconds before releasing the auger control. Repeat this several times.

5.With the throttle control in the FAST (rabbit) position and the auger control in the disengaged “up” position, walk to the front of the machine.

6.Confirm that the auger has completely stopped rotating and shows NO signs of motion. If the auger shows ANY signs of rotating, immediately return to the operator’s position and shut off the engine. Wait for ALL moving parts to stop before re-adjusting the auger control.

7.To readjust the control cable, loosen the upper hex nut on the auger cable bracket. See Figure 9.

8.Position the bracket upward to provide more slack (or downward to increase cable tension).

9.Retighten the upper hex nut.

10.Repeat steps 2-6 above to verify proper adjustment has been achieved.

Figure 8

Figure 9

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents 2007 Operator’s ManualProduct Specifications Model Number Table of ContentsWarranty Statement Repair Protection Agreement Preparation Safety InstructionsTraining Operation Maintenance & StorageThis page left intentionally blank USE CLEAN-OUT Tool to Unclog Discharge Chute Safety LabelsLoose Parts AssemblyAssembly Removing From CartonAssembly Tire Pressure AdjustmentsChute Clean-Out Tool Set-UpAuger Control Chute AssemblyIgnition Key OperationEngine Controls Shift LeverElectric Starter Button Chute AssemblyThrottle Control Recoil Starter HandleStarting The Engine Clean-Out ToolBefore Starting Engine To Engage Augers Replacing Shear PinsStopping The Engine To Engage DriveChanging Engine Oil Service and MaintenanceChecking Engine Oil Lubrication Drive Control Shave Plate and Skid ShoesAuger Belt Belt ReplacementChute Bracket Drive Belt Friction Wheel Removal Service and Maintenance Each Use Engine oil level Check Gas in the tank † Under heavy load or in high temperaturesShort-Term Storage OFF-SEASON StoragePreparing Engine Preparing Snow ThrowerTroubleshooting Craftsman Snow Thrower Model Parts ListDescription 103 749-04138A Handle, Lower Parts List 34 -00207A Guide Bracket, Drive Cable 790-00316 Craftsman Engine Model LH195SP-67514 For Snow Thrower Model 35883 Baffle Extension 650802 Screw, 1/4-20 x 5/8 Ref. No Description 640084B This page applicable in the U.S.A. and Canada only Sears Emission Control Defects Warranty CoveragePage Número DE Modelo ÍndiceDeclaración DE Garantía Especificaciones DEL ProductoAcuerdo DE Protección Para Reparaciones Preparativos Instrucciones DE SeguridadCapacitación Mantenimiento y almacenamiento OperaciónMOntaje MontajeExtracción de la unidad de la caja Partes sueltasSitúe el montaje del canal sobre la base. Vea la figura Presión de los neumáticos ConfiguraciónAjustes Herramienta de Limpieza del CanalVuelva a apretar la tuerca hexagonal superior Ajuste del montaje del canalPrueba de control de la barrena Control de obturación Palanca de cambios Llave de encendidoOperación Controles del motorSalida del arrancador eléctrico Control del estranguladorManija del arrancador de retroceso Botón del arrancador eléctricoEncendido del motor Herramienta de limpiezaAntes de encender el motor Arrancador de retroceso Detención del motorProcedimiento para engranar la transmisión Procedimiento para engranar las barrenasControl del aceite del motor Servicio Y MantenimientoMantenimiento de Motor Tapón para drenado de aceiteLubricación Para retirar las zapatas antideslizantes Placa de raspado y zapatas antideslizantesEje de la barrena Control de la transmisiónLa Correa de la barrena Reemplazo de la correaSoporte del canal Control de la barrenaLa correa de la transmisión Extracción de la rueda de fricción Nota Tenga cuidado de no dañar las roscas del eje Tanque † Bajo carga pesada o en temperaturas altas Cada Uso Nivel del aceite de motor ComprobarAlmacenaje a Corto plazo Almacenamiento Fuera DE TemporadaPreparación del motor Preparación de la máquina quitanieveSolución DE Problemas Piezas con garantía Esta página se aplica sólo en EE.UU. y CanadáMotor certificado Notas Notas Get it fixed, at your home or ours

247.88355 specifications

Sears model 247.88355 is a notable example of an advanced snowblower designed to provide efficient snow removal during harsh winter months. This product, part of Sears’ well-respected line of outdoor power equipment, embodies a perfect combination of innovative technologies, rugged construction, and user-centric features aimed at tackling even the most challenging snowy conditions.

One of the standout features of the Sears 247.88355 is its impressive performance engine. This model typically comes equipped with a powerful four-cycle engine, delivering robust horsepower that ensures it can handle heavy, wet snow and ice without any difficulty. This engine is complemented by a self-propelled system, allowing users to maneuver the snowblower with ease, reducing the physical strain often associated with snow removal tasks.

The construction of the Sears 247.88355 is another notable characteristic, with a durable steel frame that promises longevity and reliability. The auger, crafted from high-strength materials, efficiently breaks up and displaces snow, while the oversized rubber-edged auger allows for precise snow clearing. The design minimizes the chances of clogging, making it suitable for various types of snow conditions.

User comfort is also a priority in the design of the 247.88355. The Snowblower typically features ergonomic controls, which are engineered to minimize fatigue during prolonged use. Additionally, the adjustable handlebars ensure proper height for different users, allowing for an easy and comfortable grip while operating the machine.

The Sears 247.88355 incorporates advanced throw distance capabilities, allowing users to direct the snow where they want it. With adjustable deflector controls, operators can alter snow discharge heights and distances, making it effective for various environments, ranging from small driveways to larger open areas.

Furthermore, the snowblower is designed for ease of maintenance, with accessible components that facilitate routine checks and repairs. This thoughtful approach to user experience ensures that the Sears 247.88355 remains a reliable choice for homeowners seeking a dependable solution for snow management during winter months.

In summary, the Sears 247.88355 stands out due to its powerful engine, sturdy construction, user-friendly features, and advanced performance technologies. These characteristics make it a preferred option for anyone facing snowy conditions, ensuring that winter does not hinder mobility or outdoor activities.
Top Page Image Contents