Sears 247.88355 Service and Maintenance, Checking Engine Oil, Changing Engine Oil

Page 16

SERVICE AND MAINTENANCE

ENGINE MAINTENANCE

WARNING

Before lubricating, repairing, or inspecting, disengage all controls and stop engine. Wait until all moving parts have come to a complete stop.

Checking Engine Oil

1.Be sure engine is upright and level.

2.Unscrew oil fill cap from oil filler tube and wipe dipstick clean.

3.Screw oil fill cap back into oil filler tube. Tighten securely.

4.Unscrew and remove oil fill cap from oil filler tube. Note oil level. If oil reading on dipstick is below “ADD” mark, slowly add oil to reach “FULL” level. See Figure 12.

5.Screw oil fill cap back into oil filler tube. Tighten securely.

6.Wipe away any spilled oil.

FULL

aDD

Maintain Oil Level

Between FULL and ADD

Changing Engine Oil

To avoid engine damage, it is important to:

Figure 12

•Check oil level before each use and every five operating hours.

•Change oil after first two (2) operating hours and every 25 operat- ing hours thereafter.

•Engine should still be warm but not hot from recent use.

1.Locate the oil drain plug. See Figure 13.

2.Be sure the gas cap is on and is tightened securely.

3.Clean area around oil drain plug.

4.Place approved recyclable oil container under oil drain plug.

5.Remove oil drain plug and drain oil.

NOTE: Used oil must be disposed of at a proper collection center.

6.Install oil drain plug and tighten securely.

7.Refill the engine with recommended oil. See Recommended Oil Usage chart. The engine’s oil capacity is 21 ounces.

Recommended Oil Usage

Non-Multi Grade

SAE 30

Multi Grade

SAE 5W-30 or SAE 10W-30

Synthetic Multi Grade

SAE 0W-30

-20OF

 

0O F

20O F

32O F

40OF

60OF

80OF

100O F

-30OC

-20OC

-10OC

 

0O C

10OC

20OC

30OC

40OC

Oil FIll

Oil Drain

Figure 13

8.Wipe away any spilled oil.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Operator’s Manual 2007Warranty Statement Table of ContentsProduct Specifications Model Number Repair Protection Agreement Training Safety InstructionsPreparation Maintenance & Storage OperationThis page left intentionally blank Safety Labels USE CLEAN-OUT Tool to Unclog Discharge ChuteAssembly AssemblyRemoving From Carton Loose PartsAssembly Adjustments Chute Clean-Out ToolSet-Up Tire PressureChute Assembly Auger ControlOperation Engine ControlsShift Lever Ignition KeyChute Assembly Throttle ControlRecoil Starter Handle Electric Starter ButtonBefore Starting Engine Clean-Out ToolStarting The Engine Replacing Shear Pins Stopping The EngineTo Engage Drive To Engage AugersChecking Engine Oil Service and MaintenanceChanging Engine Oil Lubrication Shave Plate and Skid Shoes Drive ControlChute Bracket Belt ReplacementAuger Belt Drive Belt Friction Wheel Removal Service and Maintenance Gas in the tank † Under heavy load or in high temperatures Each Use Engine oil level CheckOFF-SEASON Storage Preparing EnginePreparing Snow Thrower Short-Term StorageTroubleshooting Parts List Craftsman Snow Thrower ModelDescription 103 749-04138A Handle, Lower Parts List 34 -00207A Guide Bracket, Drive Cable 790-00316 Craftsman Engine Model LH195SP-67514 For Snow Thrower Model 35883 Baffle Extension 650802 Screw, 1/4-20 x 5/8 Ref. No Description 640084B Sears Emission Control Defects Warranty Coverage This page applicable in the U.S.A. and Canada onlyPage Índice Declaración DE GarantíaEspecificaciones DEL Producto Número DE ModeloAcuerdo DE Protección Para Reparaciones Capacitación Instrucciones DE SeguridadPreparativos Operación Mantenimiento y almacenamientoMontaje Extracción de la unidad de la cajaPartes sueltas MOntajeSitúe el montaje del canal sobre la base. Vea la figura Configuración AjustesHerramienta de Limpieza del Canal Presión de los neumáticosPrueba de control de la barrena Ajuste del montaje del canalVuelva a apretar la tuerca hexagonal superior Palanca de cambios Llave de encendido OperaciónControles del motor Control de obturaciónControl del estrangulador Manija del arrancador de retrocesoBotón del arrancador eléctrico Salida del arrancador eléctricoAntes de encender el motor Herramienta de limpiezaEncendido del motor Detención del motor Procedimiento para engranar la transmisiónProcedimiento para engranar las barrenas Arrancador de retrocesoServicio Y Mantenimiento Mantenimiento de MotorTapón para drenado de aceite Control del aceite del motorLubricación Placa de raspado y zapatas antideslizantes Eje de la barrenaControl de la transmisión Para retirar las zapatas antideslizantesReemplazo de la correa Soporte del canalControl de la barrena La Correa de la barrenaLa correa de la transmisión Extracción de la rueda de fricción Nota Tenga cuidado de no dañar las roscas del eje Cada Uso Nivel del aceite de motor Comprobar Tanque † Bajo carga pesada o en temperaturas altasAlmacenamiento Fuera DE Temporada Preparación del motorPreparación de la máquina quitanieve Almacenaje a Corto plazoSolución DE Problemas Esta página se aplica sólo en EE.UU. y Canadá Piezas con garantíaMotor certificado Notas Notas Get it fixed, at your home or ours

247.88355 specifications

Sears model 247.88355 is a notable example of an advanced snowblower designed to provide efficient snow removal during harsh winter months. This product, part of Sears’ well-respected line of outdoor power equipment, embodies a perfect combination of innovative technologies, rugged construction, and user-centric features aimed at tackling even the most challenging snowy conditions.

One of the standout features of the Sears 247.88355 is its impressive performance engine. This model typically comes equipped with a powerful four-cycle engine, delivering robust horsepower that ensures it can handle heavy, wet snow and ice without any difficulty. This engine is complemented by a self-propelled system, allowing users to maneuver the snowblower with ease, reducing the physical strain often associated with snow removal tasks.

The construction of the Sears 247.88355 is another notable characteristic, with a durable steel frame that promises longevity and reliability. The auger, crafted from high-strength materials, efficiently breaks up and displaces snow, while the oversized rubber-edged auger allows for precise snow clearing. The design minimizes the chances of clogging, making it suitable for various types of snow conditions.

User comfort is also a priority in the design of the 247.88355. The Snowblower typically features ergonomic controls, which are engineered to minimize fatigue during prolonged use. Additionally, the adjustable handlebars ensure proper height for different users, allowing for an easy and comfortable grip while operating the machine.

The Sears 247.88355 incorporates advanced throw distance capabilities, allowing users to direct the snow where they want it. With adjustable deflector controls, operators can alter snow discharge heights and distances, making it effective for various environments, ranging from small driveways to larger open areas.

Furthermore, the snowblower is designed for ease of maintenance, with accessible components that facilitate routine checks and repairs. This thoughtful approach to user experience ensures that the Sears 247.88355 remains a reliable choice for homeowners seeking a dependable solution for snow management during winter months.

In summary, the Sears 247.88355 stands out due to its powerful engine, sturdy construction, user-friendly features, and advanced performance technologies. These characteristics make it a preferred option for anyone facing snowy conditions, ensuring that winter does not hinder mobility or outdoor activities.
Top Page Image Contents