Sears 247.88355 operating instructions Troubleshooting

Page 25

TROUBLESHOOTING

WARNING

Before performing any type of maintenance/service, disengage all controls and stop the engine. Wait until all moving parts have come to a complete stop. Disconnect spark plug wire and ground it against the engine to prevent unintended starting. Always wear safety glasses during operation or while performing any adjustments or repairs.

This section addresses minor service issues. To locate the nearest Sears Service Center or to schedule service, simply contact Sears at 1-800-4-MY-HOME®.

Problem

 

Cause

 

Remedy

Engine fails to start

1.

Choke control not in ON position

1.

Move choke control to ON position.

 

2.

Spark plug wire disconnected

2.

Connect wire to spark plug.

 

3.

Faulty spark plug

3.

Clean, adjust gap, or replace.

 

4.

Fuel tank empty or stale fuel

4.

Fill tank with clean, fresh gasoline.

 

5.

Engine not primed.

5.

Prime engine as instructed in the Operation Section.

 

6.

Safety key not inserted.

6.

Insert key fully into the switch.

 

 

 

 

 

Engine runs erratically

1.

Engine running on CHOKE

1.

Move choke control to OFF position.

 

2.

Stale fuel

2.

Fill tank with clean, fresh gasoline.

 

3.

Water or dirt in fuel system

3.

Drain fuel tank. Refill with fresh fuel.

 

4.

Carburetor out of adjustment

4.

Contact your Sears Parts & Repair Center.

 

 

 

 

 

Engine overheats

1.

Carburetor not adjusted properly

1.

Contact your Sears Parts & Repair Center.

 

 

 

 

 

Excessive vibration

1.

Loose parts or damaged auger

1.

Stop engine immediately and disconnect spark plug

 

 

 

 

wire. Tighten all bolts and nuts. If vibration continues,

 

 

 

 

have unit serviced by a Sears Parts & Repair Center.

 

 

 

 

 

Loss of power

1.

Spark plug wire loose.

1.

Connect and tighten spark plug wire.

 

2.

Gas cap vent hole plugged.

2.

Remove ice and snow from gas cap. Be certain vent

 

 

 

 

hole is clear.

 

 

 

 

 

Unit fails to propel itself

1.

Drive cable in need of adjustment

1.

Adjust drive control cable. Refer to Service and

 

 

 

 

Maintenance section.

 

2.

Drive belt loose or damaged

2.

Replace drive belt. Refer to Service and Mainte-

 

 

 

 

nance section.

 

 

 

 

 

Unit fails to discharge snow

1.

Chute assembly clogged.

1.

Stop engine immediately and disconnect spark plug

 

 

 

 

wire. Clean chute assembly and inside of auger

 

 

 

 

housing with clean-out tool or a stick.

 

2.

Foreign object lodged in auger.

2.

Stop engine immediately and disconnect spark plug

 

 

 

 

wire. Remove object from auger with clean-out tool

 

 

 

 

or a stick.

 

3.

Auger cable in need of adjustment.

3.

Adjust auger control cable. Refer to Assembly

 

 

 

 

section.

 

4.

Auger belt loose or damaged.

4.

Replace auger belt. Refer to Service and Mainte-

 

 

 

 

nance section.

 

5.

Shear pin(s) sheared.

5.

Replace with new shear pin(s).

 

 

 

 

 

25

Image 25
Contents 2007 Operator’s ManualWarranty Statement Table of ContentsProduct Specifications Model Number Repair Protection Agreement Training Safety InstructionsPreparation Operation Maintenance & StorageThis page left intentionally blank USE CLEAN-OUT Tool to Unclog Discharge Chute Safety LabelsAssembly AssemblyRemoving From Carton Loose PartsAssembly Chute Clean-Out Tool AdjustmentsSet-Up Tire PressureAuger Control Chute AssemblyEngine Controls OperationShift Lever Ignition KeyThrottle Control Chute AssemblyRecoil Starter Handle Electric Starter ButtonBefore Starting Engine Clean-Out ToolStarting The Engine Stopping The Engine Replacing Shear PinsTo Engage Drive To Engage AugersChecking Engine Oil Service and MaintenanceChanging Engine Oil Lubrication Drive Control Shave Plate and Skid ShoesChute Bracket Belt ReplacementAuger Belt Drive Belt Friction Wheel Removal Service and Maintenance Each Use Engine oil level Check Gas in the tank † Under heavy load or in high temperaturesPreparing Engine OFF-SEASON StoragePreparing Snow Thrower Short-Term StorageTroubleshooting Craftsman Snow Thrower Model Parts ListDescription 103 749-04138A Handle, Lower Parts List 34 -00207A Guide Bracket, Drive Cable 790-00316 Craftsman Engine Model LH195SP-67514 For Snow Thrower Model 35883 Baffle Extension 650802 Screw, 1/4-20 x 5/8 Ref. No Description 640084B This page applicable in the U.S.A. and Canada only Sears Emission Control Defects Warranty CoveragePage Declaración DE Garantía ÍndiceEspecificaciones DEL Producto Número DE ModeloAcuerdo DE Protección Para Reparaciones Capacitación Instrucciones DE SeguridadPreparativos Mantenimiento y almacenamiento OperaciónExtracción de la unidad de la caja MontajePartes sueltas MOntajeSitúe el montaje del canal sobre la base. Vea la figura Ajustes ConfiguraciónHerramienta de Limpieza del Canal Presión de los neumáticosPrueba de control de la barrena Ajuste del montaje del canalVuelva a apretar la tuerca hexagonal superior Operación Palanca de cambios Llave de encendidoControles del motor Control de obturaciónManija del arrancador de retroceso Control del estranguladorBotón del arrancador eléctrico Salida del arrancador eléctricoAntes de encender el motor Herramienta de limpiezaEncendido del motor Procedimiento para engranar la transmisión Detención del motorProcedimiento para engranar las barrenas Arrancador de retrocesoMantenimiento de Motor Servicio Y MantenimientoTapón para drenado de aceite Control del aceite del motorLubricación Eje de la barrena Placa de raspado y zapatas antideslizantesControl de la transmisión Para retirar las zapatas antideslizantesSoporte del canal Reemplazo de la correaControl de la barrena La Correa de la barrenaLa correa de la transmisión Extracción de la rueda de fricción Nota Tenga cuidado de no dañar las roscas del eje Tanque † Bajo carga pesada o en temperaturas altas Cada Uso Nivel del aceite de motor ComprobarPreparación del motor Almacenamiento Fuera DE TemporadaPreparación de la máquina quitanieve Almacenaje a Corto plazoSolución DE Problemas Piezas con garantía Esta página se aplica sólo en EE.UU. y CanadáMotor certificado Notas Notas Get it fixed, at your home or ours

247.88355 specifications

Sears model 247.88355 is a notable example of an advanced snowblower designed to provide efficient snow removal during harsh winter months. This product, part of Sears’ well-respected line of outdoor power equipment, embodies a perfect combination of innovative technologies, rugged construction, and user-centric features aimed at tackling even the most challenging snowy conditions.

One of the standout features of the Sears 247.88355 is its impressive performance engine. This model typically comes equipped with a powerful four-cycle engine, delivering robust horsepower that ensures it can handle heavy, wet snow and ice without any difficulty. This engine is complemented by a self-propelled system, allowing users to maneuver the snowblower with ease, reducing the physical strain often associated with snow removal tasks.

The construction of the Sears 247.88355 is another notable characteristic, with a durable steel frame that promises longevity and reliability. The auger, crafted from high-strength materials, efficiently breaks up and displaces snow, while the oversized rubber-edged auger allows for precise snow clearing. The design minimizes the chances of clogging, making it suitable for various types of snow conditions.

User comfort is also a priority in the design of the 247.88355. The Snowblower typically features ergonomic controls, which are engineered to minimize fatigue during prolonged use. Additionally, the adjustable handlebars ensure proper height for different users, allowing for an easy and comfortable grip while operating the machine.

The Sears 247.88355 incorporates advanced throw distance capabilities, allowing users to direct the snow where they want it. With adjustable deflector controls, operators can alter snow discharge heights and distances, making it effective for various environments, ranging from small driveways to larger open areas.

Furthermore, the snowblower is designed for ease of maintenance, with accessible components that facilitate routine checks and repairs. This thoughtful approach to user experience ensures that the Sears 247.88355 remains a reliable choice for homeowners seeking a dependable solution for snow management during winter months.

In summary, the Sears 247.88355 stands out due to its powerful engine, sturdy construction, user-friendly features, and advanced performance technologies. These characteristics make it a preferred option for anyone facing snowy conditions, ensuring that winter does not hinder mobility or outdoor activities.