Sears 247.88355 Operation, Engine Controls, Shift Lever, Ignition Key, Choke Control

Page 12

OPERATION

 

Drive Control

 

 

 

Auger Control

Chute

Electric Start Button

 

 

 

Assembly

Gas Cap

Shift Lever

 

 

Oil Fill

Chute Directional Control

 

 

Clean-Out Tool

 

Engine Controls

 

Recoil Starter

 

 

 

 

Handle

 

 

Electric Starter Outlet

 

 

Primer

 

 

Ignition

 

 

Key

Choke

Control

Augers

Skid Shoe

Throttle

 

 

Control

 

 

Figure 10

Now that you have setup your snow thrower, it’s important to become acquainted with its controls and features. Refer to Figure 10.

Shift Lever

The shift lever is located between the lower handles. Place the shift lever into any of seven positions to control the direction of travel and ground speed.

Forward

Your snow thrower has five forward (F) speeds. Position one (1) is the slowest and position five (5) is the fastest.

Reverse

Your snow thrower has two reverse (R) speeds. One (1) is the slower and two (2) is the faster.

Ignition Key

The ignition key is a safety device. It must be fully inserted in order for the engine to start. Remove the ignition key when the snow thrower is not in use.

NOTE: Do not turn the ignition key in an attempt to start the engine. Doing so may cause it to break.

Choke Control

The choke control is found on the rear of the engine and is activated by rotating the knob clockwise. Activating the choke control closes the choke plate on the carburetor and aids in starting the engine.

Meets ANSI Safety Standards

Craftsman Snow Throwers conform to the safety standard of the American National Standards Institute (ANSI).

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Operator’s Manual 2007Table of Contents Warranty StatementProduct Specifications Model Number Repair Protection Agreement Safety Instructions TrainingPreparation Maintenance & Storage OperationThis page left intentionally blank Safety Labels USE CLEAN-OUT Tool to Unclog Discharge ChuteAssembly AssemblyRemoving From Carton Loose PartsAssembly Adjustments Chute Clean-Out ToolSet-Up Tire PressureChute Assembly Auger ControlOperation Engine ControlsShift Lever Ignition KeyChute Assembly Throttle ControlRecoil Starter Handle Electric Starter ButtonClean-Out Tool Before Starting EngineStarting The Engine Replacing Shear Pins Stopping The EngineTo Engage Drive To Engage AugersService and Maintenance Checking Engine OilChanging Engine Oil Lubrication Shave Plate and Skid Shoes Drive ControlBelt Replacement Chute BracketAuger Belt Drive Belt Friction Wheel Removal Service and Maintenance Gas in the tank † Under heavy load or in high temperatures Each Use Engine oil level CheckOFF-SEASON Storage Preparing EnginePreparing Snow Thrower Short-Term StorageTroubleshooting Parts List Craftsman Snow Thrower ModelDescription 103 749-04138A Handle, Lower Parts List 34 -00207A Guide Bracket, Drive Cable 790-00316 Craftsman Engine Model LH195SP-67514 For Snow Thrower Model 35883 Baffle Extension 650802 Screw, 1/4-20 x 5/8 Ref. No Description 640084B Sears Emission Control Defects Warranty Coverage This page applicable in the U.S.A. and Canada onlyPage Índice Declaración DE GarantíaEspecificaciones DEL Producto Número DE ModeloAcuerdo DE Protección Para Reparaciones Instrucciones DE Seguridad CapacitaciónPreparativos Operación Mantenimiento y almacenamientoMontaje Extracción de la unidad de la cajaPartes sueltas MOntajeSitúe el montaje del canal sobre la base. Vea la figura Configuración AjustesHerramienta de Limpieza del Canal Presión de los neumáticosAjuste del montaje del canal Prueba de control de la barrenaVuelva a apretar la tuerca hexagonal superior Palanca de cambios Llave de encendido OperaciónControles del motor Control de obturaciónControl del estrangulador Manija del arrancador de retrocesoBotón del arrancador eléctrico Salida del arrancador eléctricoHerramienta de limpieza Antes de encender el motorEncendido del motor Detención del motor Procedimiento para engranar la transmisiónProcedimiento para engranar las barrenas Arrancador de retrocesoServicio Y Mantenimiento Mantenimiento de MotorTapón para drenado de aceite Control del aceite del motorLubricación Placa de raspado y zapatas antideslizantes Eje de la barrenaControl de la transmisión Para retirar las zapatas antideslizantesReemplazo de la correa Soporte del canalControl de la barrena La Correa de la barrenaLa correa de la transmisión Extracción de la rueda de fricción Nota Tenga cuidado de no dañar las roscas del eje Cada Uso Nivel del aceite de motor Comprobar Tanque † Bajo carga pesada o en temperaturas altasAlmacenamiento Fuera DE Temporada Preparación del motorPreparación de la máquina quitanieve Almacenaje a Corto plazoSolución DE Problemas Esta página se aplica sólo en EE.UU. y Canadá Piezas con garantíaMotor certificado Notas Notas Get it fixed, at your home or ours

247.88355 specifications

Sears model 247.88355 is a notable example of an advanced snowblower designed to provide efficient snow removal during harsh winter months. This product, part of Sears’ well-respected line of outdoor power equipment, embodies a perfect combination of innovative technologies, rugged construction, and user-centric features aimed at tackling even the most challenging snowy conditions.

One of the standout features of the Sears 247.88355 is its impressive performance engine. This model typically comes equipped with a powerful four-cycle engine, delivering robust horsepower that ensures it can handle heavy, wet snow and ice without any difficulty. This engine is complemented by a self-propelled system, allowing users to maneuver the snowblower with ease, reducing the physical strain often associated with snow removal tasks.

The construction of the Sears 247.88355 is another notable characteristic, with a durable steel frame that promises longevity and reliability. The auger, crafted from high-strength materials, efficiently breaks up and displaces snow, while the oversized rubber-edged auger allows for precise snow clearing. The design minimizes the chances of clogging, making it suitable for various types of snow conditions.

User comfort is also a priority in the design of the 247.88355. The Snowblower typically features ergonomic controls, which are engineered to minimize fatigue during prolonged use. Additionally, the adjustable handlebars ensure proper height for different users, allowing for an easy and comfortable grip while operating the machine.

The Sears 247.88355 incorporates advanced throw distance capabilities, allowing users to direct the snow where they want it. With adjustable deflector controls, operators can alter snow discharge heights and distances, making it effective for various environments, ranging from small driveways to larger open areas.

Furthermore, the snowblower is designed for ease of maintenance, with accessible components that facilitate routine checks and repairs. This thoughtful approach to user experience ensures that the Sears 247.88355 remains a reliable choice for homeowners seeking a dependable solution for snow management during winter months.

In summary, the Sears 247.88355 stands out due to its powerful engine, sturdy construction, user-friendly features, and advanced performance technologies. These characteristics make it a preferred option for anyone facing snowy conditions, ensuring that winter does not hinder mobility or outdoor activities.
Top Page Image Contents