Sears 247.88355 Throttle Control, Recoil Starter Handle, Electric Starter Button, Augers, Primer

Page 13

OPERATION

Throttle Control

The throttle control is located on the rear of the engine. It regulates the speed of the engine and will shut off the engine when moved into the STOP position.

Recoil Starter Handle

This handle is used to manually start the engine.

Electric Starter Button

Pressing the electric starter button engages the engine’s electric starter when plugged into a 120V power source.

Electric Starter Outlet

Requires the use of a three-prong outdoor extension cord (included) and a 120V power source/wall outlet.

Augers

When engaged, the augers rotate and draw snow into the auger housing.

Chute Assembly

Snow drawn into the auger housing is discharged out the chute assembly.

Primer

Depressing the primer forces fuel directly into the engine’s carburetor to aid in cold-weather starting.

Oil Fill

Engine oil level can be checked and oil added through the oil fill.

Gas Cap

Unthread the gas cap to add gasoline to the fuel tank.

Auger Control

AUGER

CONTROL

GO

The auger control is located on the left handle. Squeeze the control grip against the handle to engage the augers and start snow throwing action. Release to stop.

Drive Control/ Auger Control Lock

DRIVE

CONTROL

GO

The drive control is located on the right handle. Squeeze the control grip against the handle to engage the wheel drive. Release to stop.

NOTE: Always release the drive control before changing speeds. Failure to do so will result in increased wear on your machine’s drive system.

Chute Directional Control

CHUTE DIRECTIONAL CONTROL

		ADJUSTABLE
DISCHARGE	DISCHARGE	CHUTE TILT
LEFT	RIGHT

The chute directional control is located on left side of the snow thrower. To change the direction in which snow is thrown, turn chute directional control as follows:

•Crank clockwise to discharge to the left.

•Crank counterclockwise to discharge to the right.

Skid Shoes

Position the skid shoes based on surface conditions. Adjust upward for hard-packed snow. Adjust downward when operating on gravel or crushed rock surfaces.

13

Image 13

Contents 2007 Operator’s ManualWarranty Statement Table of ContentsProduct Specifications Model Number Repair Protection Agreement Training Safety InstructionsPreparation Operation Maintenance & StorageThis page left intentionally blank USE CLEAN-OUT Tool to Unclog Discharge Chute Safety LabelsAssembly AssemblyRemoving From Carton Loose PartsAssembly Chute Clean-Out Tool Adjustments Set-Up Tire PressureAuger Control Chute AssemblyEngine Controls OperationShift Lever Ignition KeyThrottle Control Chute AssemblyRecoil Starter Handle Electric Starter ButtonBefore Starting Engine Clean-Out ToolStarting The Engine Stopping The Engine Replacing Shear PinsTo Engage Drive To Engage AugersChecking Engine Oil Service and MaintenanceChanging Engine Oil Lubrication Drive Control Shave Plate and Skid ShoesChute Bracket Belt ReplacementAuger Belt Drive Belt Friction Wheel Removal Service and Maintenance Each Use Engine oil level Check Gas in the tank † Under heavy load or in high temperaturesPreparing Engine OFF-SEASON StoragePreparing Snow Thrower Short-Term StorageTroubleshooting Craftsman Snow Thrower Model Parts ListDescription 103 749-04138A Handle, Lower Parts List 34 -00207A Guide Bracket, Drive Cable 790-00316 Craftsman Engine Model LH195SP-67514 For Snow Thrower Model 35883 Baffle Extension 650802 Screw, 1/4-20 x 5/8 Ref. No Description 640084B This page applicable in the U.S.A. and Canada only Sears Emission Control Defects Warranty CoveragePage Declaración DE Garantía ÍndiceEspecificaciones DEL Producto Número DE ModeloAcuerdo DE Protección Para Reparaciones Capacitación Instrucciones DE SeguridadPreparativos Mantenimiento y almacenamiento OperaciónExtracción de la unidad de la caja MontajePartes sueltas MOntajeSitúe el montaje del canal sobre la base. Vea la figura Ajustes ConfiguraciónHerramienta de Limpieza del Canal Presión de los neumáticosPrueba de control de la barrena Ajuste del montaje del canalVuelva a apretar la tuerca hexagonal superior Operación Palanca de cambios Llave de encendidoControles del motor Control de obturaciónManija del arrancador de retroceso Control del estranguladorBotón del arrancador eléctrico Salida del arrancador eléctricoAntes de encender el motor Herramienta de limpiezaEncendido del motor Procedimiento para engranar la transmisión Detención del motorProcedimiento para engranar las barrenas Arrancador de retrocesoMantenimiento de Motor Servicio Y MantenimientoTapón para drenado de aceite Control del aceite del motorLubricación Eje de la barrena Placa de raspado y zapatas antideslizantesControl de la transmisión Para retirar las zapatas antideslizantesSoporte del canal Reemplazo de la correaControl de la barrena La Correa de la barrenaLa correa de la transmisión Extracción de la rueda de fricción Nota Tenga cuidado de no dañar las roscas del eje Tanque † Bajo carga pesada o en temperaturas altas Cada Uso Nivel del aceite de motor ComprobarPreparación del motor Almacenamiento Fuera DE TemporadaPreparación de la máquina quitanieve Almacenaje a Corto plazoSolución DE Problemas Piezas con garantía Esta página se aplica sólo en EE.UU. y CanadáMotor certificado Notas Notas Get it fixed, at your home or ours