Sears 247.88355 operating instructions Service and Maintenance

Page 22

SERVICE AND MAINTENANCE

6.Carefully remove the hex nut and washer which secures the hex shaft to the snow thrower frame and lightly tap the shaft’s end to dislodge the ball bearing from the right side of the frame. See Figure 28.

NOTE: Be careful not to damage the threads on the shaft.

7.Carefully position the hex shaft downward and to the left before carefully sliding the friction wheel assembly off the shaft. See Figure 29.

NOTE: If you’re replacing the friction wheel assembly as a whole, discard the worn part and slide the new part onto the hex shaft.

Follow the steps above in reverse order to reassemble components. If you’re disassembling the friction wheel and replacing only the rubber ring, proceed as follows:

1.Remove the four screws which secure the friction wheel’s side plates together. See Figure 30.

2.Remove the rubber ring from between the plates.

3.Reassemble the side plates with a new rubber ring.

NOTE: When reassembling the friction wheel assembly, make sure that the rubber ring is centered and seated properly between the side plates. Tighten each screw only one rotation before turning the wheel clockwise and proceeding with the next screw. Repeat this process several times to ensure the plates are secured with equal force (between 6 ft-lbs and 9 ft-lbs).

4.Slide the friction wheel assembly back onto the hex shaft and follow the steps above in reverse order to reassemble components.

Figure 28

Figure 29

Figure 30

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Operator’s Manual 2007Warranty Statement Table of ContentsProduct Specifications Model Number Repair Protection Agreement Training Safety InstructionsPreparation Maintenance & Storage OperationThis page left intentionally blank Safety Labels USE CLEAN-OUT Tool to Unclog Discharge ChuteRemoving From Carton AssemblyAssembly Loose PartsAssembly Set-Up AdjustmentsChute Clean-Out Tool Tire PressureChute Assembly Auger ControlShift Lever OperationEngine Controls Ignition KeyRecoil Starter Handle Chute AssemblyThrottle Control Electric Starter ButtonBefore Starting Engine Clean-Out ToolStarting The Engine To Engage Drive Replacing Shear PinsStopping The Engine To Engage AugersChecking Engine Oil Service and MaintenanceChanging Engine Oil Lubrication Shave Plate and Skid Shoes Drive ControlChute Bracket Belt ReplacementAuger Belt Drive Belt Friction Wheel Removal Service and Maintenance Gas in the tank † Under heavy load or in high temperatures Each Use Engine oil level CheckPreparing Snow Thrower OFF-SEASON StoragePreparing Engine Short-Term StorageTroubleshooting Parts List Craftsman Snow Thrower ModelDescription 103 749-04138A Handle, Lower Parts List 34 -00207A Guide Bracket, Drive Cable 790-00316 Craftsman Engine Model LH195SP-67514 For Snow Thrower Model 35883 Baffle Extension 650802 Screw, 1/4-20 x 5/8 Ref. No Description 640084B Sears Emission Control Defects Warranty Coverage This page applicable in the U.S.A. and Canada onlyPage Especificaciones DEL Producto ÍndiceDeclaración DE Garantía Número DE ModeloAcuerdo DE Protección Para Reparaciones Capacitación Instrucciones DE SeguridadPreparativos Operación Mantenimiento y almacenamientoPartes sueltas MontajeExtracción de la unidad de la caja MOntajeSitúe el montaje del canal sobre la base. Vea la figura Herramienta de Limpieza del Canal ConfiguraciónAjustes Presión de los neumáticosPrueba de control de la barrena Ajuste del montaje del canalVuelva a apretar la tuerca hexagonal superior Controles del motor Palanca de cambios Llave de encendidoOperación Control de obturaciónBotón del arrancador eléctrico Control del estranguladorManija del arrancador de retroceso Salida del arrancador eléctricoAntes de encender el motor Herramienta de limpiezaEncendido del motor Procedimiento para engranar las barrenas Detención del motorProcedimiento para engranar la transmisión Arrancador de retrocesoTapón para drenado de aceite Servicio Y MantenimientoMantenimiento de Motor Control del aceite del motorLubricación Control de la transmisión Placa de raspado y zapatas antideslizantesEje de la barrena Para retirar las zapatas antideslizantesControl de la barrena Reemplazo de la correaSoporte del canal La Correa de la barrenaLa correa de la transmisión Extracción de la rueda de fricción Nota Tenga cuidado de no dañar las roscas del eje Cada Uso Nivel del aceite de motor Comprobar Tanque † Bajo carga pesada o en temperaturas altasPreparación de la máquina quitanieve Almacenamiento Fuera DE TemporadaPreparación del motor Almacenaje a Corto plazoSolución DE Problemas Esta página se aplica sólo en EE.UU. y Canadá Piezas con garantíaMotor certificado Notas Notas Get it fixed, at your home or ours

247.88355 specifications

Sears model 247.88355 is a notable example of an advanced snowblower designed to provide efficient snow removal during harsh winter months. This product, part of Sears’ well-respected line of outdoor power equipment, embodies a perfect combination of innovative technologies, rugged construction, and user-centric features aimed at tackling even the most challenging snowy conditions.

One of the standout features of the Sears 247.88355 is its impressive performance engine. This model typically comes equipped with a powerful four-cycle engine, delivering robust horsepower that ensures it can handle heavy, wet snow and ice without any difficulty. This engine is complemented by a self-propelled system, allowing users to maneuver the snowblower with ease, reducing the physical strain often associated with snow removal tasks.

The construction of the Sears 247.88355 is another notable characteristic, with a durable steel frame that promises longevity and reliability. The auger, crafted from high-strength materials, efficiently breaks up and displaces snow, while the oversized rubber-edged auger allows for precise snow clearing. The design minimizes the chances of clogging, making it suitable for various types of snow conditions.

User comfort is also a priority in the design of the 247.88355. The Snowblower typically features ergonomic controls, which are engineered to minimize fatigue during prolonged use. Additionally, the adjustable handlebars ensure proper height for different users, allowing for an easy and comfortable grip while operating the machine.

The Sears 247.88355 incorporates advanced throw distance capabilities, allowing users to direct the snow where they want it. With adjustable deflector controls, operators can alter snow discharge heights and distances, making it effective for various environments, ranging from small driveways to larger open areas.

Furthermore, the snowblower is designed for ease of maintenance, with accessible components that facilitate routine checks and repairs. This thoughtful approach to user experience ensures that the Sears 247.88355 remains a reliable choice for homeowners seeking a dependable solution for snow management during winter months.

In summary, the Sears 247.88355 stands out due to its powerful engine, sturdy construction, user-friendly features, and advanced performance technologies. These characteristics make it a preferred option for anyone facing snowy conditions, ensuring that winter does not hinder mobility or outdoor activities.
Top Page Image Contents