Sears 247.88355 operating instructions Friction Wheel Removal

Page 21

SERVICE AND MAINTENANCE

3.Remove the belt as follows. Refer to Figure 25. a. Roll the auger belt off the engine pulley.

b. Use a wrench to pivot the idler pulley toward the right.

C

A

c.Lift the drive belt off engine pulley.

4.Carefully pivot the snow thrower up and forward so that it rests on the auger housing.

5.Remove the frame cover from the underside of the snow thrower by removing four self-tapping screws which secure it. Refer to Figure 22.

6.Slip the drive belt off the pulley and between friction wheel and friction wheel disc. See Figure 26.

7.Remove and replace belt in the reverse order.

NOTE: Engaging the drive control will ease reassembly of the belt.

Friction Wheel Removal

B

If the snow thrower fails to drive with the drive control engaged,

and performing the drive control cable adjustment fails to correctFigure 25 the problem, the friction wheel may need to be replaced. Follow the

instructions below. Examine the friction wheel for signs of wear or cracking and replace if necessary.

1.Place a piece of plastic under the gas cap.

2.Place the shift lever in third Forward (F3) position.

3.Carefully pivot the snow thrower up and forward so that it rests on the auger housing.

4.Remove the frame cover from the underside of the snow thrower by removing four self-tapping screws which secure it.

5.Remove the right-hand wheel by removing the screw and bell

washer which secure it to the axle. See Figure 27.

Figure 26

Figure 27

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents 2007 Operator’s ManualTable of Contents Warranty StatementProduct Specifications Model Number Repair Protection Agreement Safety Instructions TrainingPreparation Operation Maintenance & StorageThis page left intentionally blank USE CLEAN-OUT Tool to Unclog Discharge Chute Safety LabelsAssembly AssemblyRemoving From Carton Loose PartsAssembly Chute Clean-Out Tool AdjustmentsSet-Up Tire PressureAuger Control Chute AssemblyEngine Controls OperationShift Lever Ignition KeyThrottle Control Chute AssemblyRecoil Starter Handle Electric Starter ButtonClean-Out Tool Before Starting EngineStarting The Engine Stopping The Engine Replacing Shear PinsTo Engage Drive To Engage AugersService and Maintenance Checking Engine OilChanging Engine Oil Lubrication Drive Control Shave Plate and Skid ShoesBelt Replacement Chute BracketAuger Belt Drive Belt Friction Wheel Removal Service and Maintenance Each Use Engine oil level Check Gas in the tank † Under heavy load or in high temperaturesPreparing Engine OFF-SEASON StoragePreparing Snow Thrower Short-Term StorageTroubleshooting Craftsman Snow Thrower Model Parts ListDescription 103 749-04138A Handle, Lower Parts List 34 -00207A Guide Bracket, Drive Cable 790-00316 Craftsman Engine Model LH195SP-67514 For Snow Thrower Model 35883 Baffle Extension 650802 Screw, 1/4-20 x 5/8 Ref. No Description 640084B This page applicable in the U.S.A. and Canada only Sears Emission Control Defects Warranty CoveragePage Declaración DE Garantía ÍndiceEspecificaciones DEL Producto Número DE ModeloAcuerdo DE Protección Para Reparaciones Instrucciones DE Seguridad CapacitaciónPreparativos Mantenimiento y almacenamiento OperaciónExtracción de la unidad de la caja MontajePartes sueltas MOntajeSitúe el montaje del canal sobre la base. Vea la figura Ajustes ConfiguraciónHerramienta de Limpieza del Canal Presión de los neumáticosAjuste del montaje del canal Prueba de control de la barrenaVuelva a apretar la tuerca hexagonal superior Operación Palanca de cambios Llave de encendidoControles del motor Control de obturaciónManija del arrancador de retroceso Control del estranguladorBotón del arrancador eléctrico Salida del arrancador eléctricoHerramienta de limpieza Antes de encender el motorEncendido del motor Procedimiento para engranar la transmisión Detención del motorProcedimiento para engranar las barrenas Arrancador de retrocesoMantenimiento de Motor Servicio Y MantenimientoTapón para drenado de aceite Control del aceite del motorLubricación Eje de la barrena Placa de raspado y zapatas antideslizantesControl de la transmisión Para retirar las zapatas antideslizantesSoporte del canal Reemplazo de la correaControl de la barrena La Correa de la barrenaLa correa de la transmisión Extracción de la rueda de fricción Nota Tenga cuidado de no dañar las roscas del eje Tanque † Bajo carga pesada o en temperaturas altas Cada Uso Nivel del aceite de motor ComprobarPreparación del motor Almacenamiento Fuera DE TemporadaPreparación de la máquina quitanieve Almacenaje a Corto plazoSolución DE Problemas Piezas con garantía Esta página se aplica sólo en EE.UU. y CanadáMotor certificado Notas Notas Get it fixed, at your home or ours

247.88355 specifications

Sears model 247.88355 is a notable example of an advanced snowblower designed to provide efficient snow removal during harsh winter months. This product, part of Sears’ well-respected line of outdoor power equipment, embodies a perfect combination of innovative technologies, rugged construction, and user-centric features aimed at tackling even the most challenging snowy conditions.

One of the standout features of the Sears 247.88355 is its impressive performance engine. This model typically comes equipped with a powerful four-cycle engine, delivering robust horsepower that ensures it can handle heavy, wet snow and ice without any difficulty. This engine is complemented by a self-propelled system, allowing users to maneuver the snowblower with ease, reducing the physical strain often associated with snow removal tasks.

The construction of the Sears 247.88355 is another notable characteristic, with a durable steel frame that promises longevity and reliability. The auger, crafted from high-strength materials, efficiently breaks up and displaces snow, while the oversized rubber-edged auger allows for precise snow clearing. The design minimizes the chances of clogging, making it suitable for various types of snow conditions.

User comfort is also a priority in the design of the 247.88355. The Snowblower typically features ergonomic controls, which are engineered to minimize fatigue during prolonged use. Additionally, the adjustable handlebars ensure proper height for different users, allowing for an easy and comfortable grip while operating the machine.

The Sears 247.88355 incorporates advanced throw distance capabilities, allowing users to direct the snow where they want it. With adjustable deflector controls, operators can alter snow discharge heights and distances, making it effective for various environments, ranging from small driveways to larger open areas.

Furthermore, the snowblower is designed for ease of maintenance, with accessible components that facilitate routine checks and repairs. This thoughtful approach to user experience ensures that the Sears 247.88355 remains a reliable choice for homeowners seeking a dependable solution for snow management during winter months.

In summary, the Sears 247.88355 stands out due to its powerful engine, sturdy construction, user-friendly features, and advanced performance technologies. These characteristics make it a preferred option for anyone facing snowy conditions, ensuring that winter does not hinder mobility or outdoor activities.
Top Page Image Contents