Husqvarna Complete Guide to the 8024STE Snow Blower Maintenance and Operation
Page 47

 

 

To remove belt cover

 

B

1.

Remove the two (2) screws (A) securing belt cover (B) to frame (C).

 

2.

Remove belt cover.

 

 

 

 

•

Replace belt cover by installing cover and screws and tighten se-

 

 

 

curely.

 

 

Entfernen der riemenabdeckung

 

 

1.

Entfernen Sie die zwei (2) Schrauben (A), mit denen die Riemena-

 

 

 

beckung (B) am Rahmen (C) befestigt ist.

 

 

2.

Entfernen Sie die Riemenabdeckung.

 

 

•

Befestigen Sie die Riemenabdeckung erneut, indem Sie die Abdeck-

C

 

A

ung und die Schrauben wieder anbringen und die Schrauben fest

 

anziehen.

Pour enlever le couvercle de la courroie

Het verwijderen van de riemhuls

1.

Enlevez les deux (2) vis (A) en fixant le couvercle de la

1.

Verwijder de twee (2) schroeven (A) die de riemhuls (B)

 

courroie (B) au châssis (C).

 

aan het frame (C) bevestigen.

2.

Enlevez le couvercle de la courroie.

2.

Verwijder de riemhuls.

•

Remplacez le couvercle de la courroie en installant le

•

Zet de riemhuls weer terug door de huls en de schroeven

 

couvercle et serrez solidement.

 

terug te plaatsen en draai stevig aan.

Desmontar el cubre correas

1.Desmontar los dos (2) tornillos (A) que sujetan el cubre correas (B) a la carcasa (C).

2.Desmontar el cubre correas.

•Sustituir el cubre correas colocando la cubierta y los tornillos y apretando firmemente.

Rimuovere il coperchio della cinghia

1.Togliere le due (2) viti (A) che fissano il coperchio della cinghia (B) all’intelaiatura (C).

2.Togliere il coperchio della cinghia.

•Rimettere coperchio e viti, stringendo bene.

2

 

1

 

3

 

 

L K A

 

J

D C B

H

 

 

 

 

M

 

 

E

 

 

F

 

 

G

 

2

1

 

To replace belts

The auger and traction drive belts are not adjustable. If the belts are dam- aged or begin to slip from wear, they should be replaced. It is recommended that the belt(s) be replaced by a qualified service center.

NOTE: It is recommended that both the auger and traction drive belt be replaced at the same time.

The V-belts on your snow thrower are of special construction and should be replaced by original equipment manufacturer (OEM) belts available from your nearest dealer. Using other than OEM belts can cause personal injury or damage to the snow thrower.

WARNING: Belt replacement requires separation of the snow thrower. While separating the auger housing (1) from the frame assembly (2), it is important that an assistant stand in the oper- ating position and hold the snow thrower handles (3). Serious personal injury and/or damage to the unit could occur if the snow thrower should fall during the belt changing process.

1.REMOVE GASOLINE FROM FUEL TANK - Drain gasoline from fuel tank into a suitable container, outdoors, away from fire or flame. Wipe up any spilled gasoline.

2.REMOVE DISCHARGE CHUTE - Loosen lock nut securing chute rota- tor head to mounting bracket only enough to allow chute rotator head to be raised and discharge chute to be removed from snow thrower.

3.REMOVE BELT COVER - See “TO REMOVE BELT COVER” in this section of this manual.

4.REMOVE ENGINE PULLEY (A) - Remove bolt (B), lock washer (C) and flat washer (D) securing pulley to engine crankshaft. Remove outside (auger) pulley (A) only from crankshaft.

5.SEPARATE SNOW THROWER - With your assistant standing in the operating position holding the handles, remove the two bolts (F) and lock washers (G) holding auger housing (1) and frame (2) together.

WARNING: As the last bolt is removed, have your assistant care- fully lower the handles down to the ground.

6.REMOVE AUGER BELT (H) from around pulley (E).

7.RELIEVE TENSION ON TRACTION DRIVE BELT IDLER (J) and remove traction drive belt (K) from around pulleys.

HINT: Insert a 3/8" drive ratchet (in the “ON” position) into the square hole in idler arm (J) and rotate ratchet clockwise to relieve tension.

47

Page 46 Page 48
Image 47
Page 46 Page 48
Contents 5524ST 8024STE, 1130STE Contents Indice Sichere Bedienung einer Schnee- fräse Préparation BedienungWartung und Lagerung InstructionsFormación Técnicas de funcionamiento seguro para máquinas quitanievesFonctionnement Entretien et rangementVoorbereiding FuncionamientoMantenimiento y Conservación InstructiesPreparazione Procedure di sicurezza per l’utilizzo di spazzaneveOnderhoud en Opslag AddestramentoManutenzione e conservazione 5524ST 8024STE 1130STE Sacar la máquina quitanieves del cartón Remove snow thrower from the cartonEntnehmen der Schneefräse aus dem Karton Enlever la souffleuse de la caisse en cartonComo preparar su máquina quita- nieves How to set up your snow throwerComment installer votre souffleuse Zusammensetzen der SchneefräseHet uitpakken van de bovenste hendel Het installeren van de staaf van de snelheidsregelingInstall traction drive control rod Installation des fahrantriebssteuerhebelsHet installeren van de regelstang van de boor- regeling Install auger control rodInstallation des Steuerhebels für die einzugssch- necken Installez la tige de contrôle de la vis sans finHet installeren van de afvoertrechter / rotorkop Install discharge chute / chute rotater headÜberprüfen des reifendrucks Install chute deflector remote controlMontar el mando a distancia del deflector del conducto Check tire pressure Controlar la presión de los neumáticosG K a Werkzeugkasten Como utilizar su máquina quita- Nieves How to use your snow throwerBedienung der schneefräse Comment utiliser votre souffleuseUsar el mando del cebador E Pour utiliser la commande d’étrangleur ETo use choke control E Bedienung des choke EPour contrôler la décharge de la neige 5524ST 8024STE, 1130STETo control snow discharge Regelung des schneeauswurfsRegolare la bocca di scarico della neve Controlar la eyección de la nieveHet bedienen van de sneeuwuitstoot Pour lancer de la neige Using the clean-out toolTo throw snow Das schneefräsenUtilizzo dello strumento di pulitura Utilisation de l’outil de nettoyageUsar la herramienta para la limpieza De ontstopper gebruikenMoverse adelante y atrás To move forward and backwardVorwärts und rückwärts fahren Pour se déplacer vers l’avant et vers l’arrière1130STE Schaber P To adjust skid plates NScraper bar P Einstellen der gleitkufen NPer regoalre la piastra di slittamento N Regular las placas de deslizamiento NBarra de arrastre P Het afstellen van de remplaten NBefore Starting the Engine R FVoordat U DE Motor Start VOR DEM MotorstartAvant DE Mettre LE Moteur EN Marche Antes DE Poner EN Marcha EL MotorMotor anlassen To start engineBefore stopping If recoil starter has frozenPour mettre le moteur en marche Vor dem ausschaltenWenn der anreißstarter eingefroren ist Antes de parar Avant l’arrêtSi le démarreur manuel a gelé Puesta en marcha del motorAls de terugloopstarter is bevroren Si el arrancador de retroceso se ha congeladoDe motor starten Voordat u stoptSe il motorino di avviamento a strappo si gela Avviare il motorePrima dell’arresto Consejos para lanzar la nieve Snow throwing tipsHinweise für das schneefräsen Wartungsnachweis Service RecordTips voor het sneeuwruimen Consigli per spazzare la neveDati di servizio Schema dentretienService aantekeningen Informe de servicioCourroies en Transmission du dispositif de déplacementGetriebegehäuse der einzugsschnecken FahrantriebssystemMotor EngineMoteur Motore Limpieza CleaningReinigung NettoyageSpazzaneve SouffleuseMáquina Quitanieves SneeuwruimerScherbolzen Shear boltsPernos de seguridad Vis de cisaillementPerni di sicurezza SchuifboutenRimuovere il coperchio della cinghia To remove belt coverEntfernen der riemenabdeckung Desmontar el cubre correasErneuern der riemen Pour remplacer les courroies Het vervangen van de riemen Sustituir las correasTogliere LA Cinghia Della Coclea H dalla puleggia E Sostituire le cinghieHET Verwijderen VAN DE Motorriemschijf La macchina5524ST, 8024STE 1130STE Velocidad del motor CarburetorEngine speed CarburadorSonstiges StorageOther LagerungDivers EntreposageAlmacenaje SouffleuseAltro OpslagOverig ImmagazzinaggioStörungssuche TroubleshootingRecherche des causes d’une panne Solución de problemasHET Probleem DE Oorzaak DE Oplossing Probleemoplosser532 41 40-23 Rev 07.29.08 BY/TH

8024STE specifications

The Husqvarna 8024STE is a standout snowblower that seamlessly blends power, efficiency, and user-friendly design, making it an excellent choice for homeowners and professionals alike. This robust machine is engineered to tackle heavy snowfall, providing a reliable solution in the coldest of winters.

At the heart of the Husqvarna 8024STE is a powerful 24-inch clearing width, allowing it to efficiently clear large areas in minimal time. With an impressive throwing distance of up to 50 feet, this snowblower ensures that snow is not only cleared but also thrown far enough to keep walkways and driveways clear of drifting snow.

One of the key features of the 8024STE is its innovative Husqvarna SnowKing engine. This engine is designed for performance, featuring high torque and an easy-start mechanism that allows users to get started without difficulty. It operates smoothly even in extreme conditions, ensuring that you can count on it when the weather turns harsh.

The snowblower's heavy-duty construction is designed to withstand demanding tasks. The auger and impeller are constructed from durable materials, providing enhanced durability and performance. The auger's design allows for efficient snow gathering and movement, while the high-capacity impeller ensures that snow is discharged effectively.

The 8024STE also boasts a range of user-friendly features, including a convenient electric start option. This allows for effortless starting in cold temperatures. The machine is equipped with large, rugged tires that provide excellent traction, allowing it to navigate through deep snow and icy conditions with ease.

Another noteworthy characteristic is its adjustable skid shoes, which allow for customizable height adjustments to suit different surfaces, whether you're clearing gravel or asphalt. The industrial-grade metal chute and deflector enable precise control over where you want the snow to go, further enhancing its usability.

In terms of ergonomics, the Husqvarna 8024STE features a comfortable control panel and heated hand grips, which make it easier to operate in frigid temperatures. The steering is designed for easy maneuverability, allowing operators to turn and navigate tight spaces efficiently.

With its combination of power, advanced features, and careful engineering, the Husqvarna 8024STE is designed to deliver reliable snow removal performance, helping to make winter maintenance more manageable for users. Whether for residential driveways or commercial lots, this snowblower stands out as a robust solution to winter's challenges.
Top Page Image Contents