Intel SBC-455 manual Specifications

Page 12

Specifications

CPU: 80486SX/DX/DX2/DX4 25/33/40/50/66/75/100/120 MHz, 5x86-100/120/ 133 or Pentium OverDrive processor

Bus interface: ISA bus

Data bus: 32-bit

Processing ability: 32-bit

Chipset: ALI/1489/1487

RAM memory: 1 MB to 64 MB. Uses two 72-pin SIMM sockets

L2 Cache memory size: 128/256/512 KB 2nd level cache memory

Shadow RAM memory: Supports system and video BIOS shadow memory

Flat panel/CRT SVGA controller: SVGA, PCI-bus, CHIPS 65548 chipset with 512 KB standard video memory, upgradable to 1 MB. Provides 32-bit graphic throughput. Features the ability to control most TFT, STN, B/W, EL flat panel displays as well as standard CRT. Supports resolutions up to 1024 x 768 in 256 colors. Daughterboards available for various flat panel displays.

Enhanced IDE hard disk drive interface: Fast PCI bus. Supports up to two Enhanced IDE (ATA-2) large hard disk drives or other Enhanced IDE devices. Supports mode 3 and mode 4 hard disks (data transfer rate 11.1 MB/ sec. minimum)

Floppy disk drive interface: Supports up to two floppy disk drives, 5 1/ 4"¼" (360 KB and 1.2 MB) and/or 3 1/2" (720 KB, 1.44 and 2.88 MB)

Bidirectional parallel port: Configurable to LPT1, LPT2, LPT3 or disabled Supports SPP/EPP/ECP standards

Serial ports: Two serial RS-232 ports, uses 16C550 UARTs with 16-byte FIFO buffer. Supports speeds up to 115 Kbps. Ports can be individually configured from COM1 to COM4 or disabled.

BIOS: AMI Flash WIN BIOS

Watchdog timer: Can generate a system reset or IRQ15. The time interval is software selectable from 2 to 32 seconds (15 steps, 2 seconds per step).

PC/104: 104-pin connector for a 16-bit bus

DMA channels: 7

4 SBC-455 User's Manual

Image 12

Contents Page FCC Statement Copyright Notice AcknowledgementsPacking list Contents Keyboard and PS/2 KB/ mouse connections Chpater 4 Flat Panel/CRT Controller Display Drivers Page General Information Introduction Features Specifications Bus speed 8 MHz Board layout P 6 8 T 8 4 MCard dimensions Page Installation Jumpers and connectors Label FunctionLocating jumpers and connectors Setting jumpers Safety precautions Installing the CPURemoving a CPU Installing a CPU CPU type select JP1, JP3, JP4 CPU Type select JP4, JP3, JP1CPU Vcc select JP2 CPU clock select JP9, JP10Installing Dram SIMMs Installing SIMMsRemoving SIMMs Connecting the hard drive IDE hard drive connections IDEIDE LED IDE LED Connecting the floppy drive Floppy drive connections Floppy DiskInstalling the retaining bracket Parallel port PrinterPower supply connections Power CON Power supply connectorParallel port DRQ and Dack JP11 Display connections VGA, LCD LCD signal select JP5, JP7 Keyboard and PS/2 KB/ mouse connections KB CON, KB/PS2 Mouse Serial ports RS-232 connections COM A, COM BSerial ports IRQ select JP11 Watchdog timer setup Watchdog timer time-out signal select JP6Watchdog timer programming Delay time Value Hex External switches and LEDs Power LED and keylock KEY LockExternal speaker EXT SPK Reset switch Reset SW Turbo LED Turbo LEDSMI System Management Interrupt switch SMI SW Turbo Switch Turbo SWClear Cmos JP12 Flash Bios Protect JP8 Flash Bios Write-enable Voltage JP13Page AMI WinBIOS Setup Starting WinBIOS setup WinBIOS main menuUsing a mouse with WinBIOS setup Using the keyboard with WinBIOS setupSetup Standard SetupFloppy A, Floppy B Advanced Setup Setting Description Turbo Switch Press F1 to continue SettingDescription Execution Chipset Setup Function OptionsFast Power Management Setup PCI/PnP Setup PCI Latency Timer in PCI Clocks IRQ3 IRQ4 IRQ5 IRQ7 IRQ9 IRQ10 IRQ11 IRQ12 IRQ14 IRQ15 Reserved Memory Size Peripheral Setup EPP Parallel Port DMA Channel Utility Security Following screen appears when you select the password icon Changing a password Default Exiting WinBIOS Page Flat Panel/CRT Controller Display Driv- ersandUtilities Hardware configuration Software driversNecessary prerequisites Before you beginDriver installation WindowsÔDriver installation Windows Setup Windows ÔDOS OS/2 VGAOS/2 Diskette copies of the OS/2 drivers must have a Windows Ô NT Windows NT Software Utilities Chipsdsp utility programFlat Panel/ CRT Controller Installing the utility How to use the utilityChipscpl utility program Flat Panel/ CRT Controller Page Watchdog Timer Demo Program Dog=dog/2 End=clock Page Installing PC/104 Modules PCM-3660 Mount the PC/104 module onto the CPU card. Do this PC/104 module dimensions inches ±5% LCD Display Bios Configuration Configuring various LCD display Appendix C LCD Display Bios Configuration C-89