Intel SBC-455 manual Parallel port Printer, Installing the retaining bracket

Page 29

Parallel port (PRINTER)

Normally, the parallel port is used to connect the card to a printer. The SBC-455 includes an on-board parallel port, accessed through the PRINTER connector, a 26-pin flat-cable connector. The CPU card comes with an adapter cable, which lets you use a traditional DB-25 connector. The cable has a 26-pin connector on one end and a DB-25 connector on the other, mounted on a retaining bracket.

Installing the retaining bracket

The retaining bracket installs at an empty slot in your system's chassis. It provides an external port that allows your parallel peripheral to access to the card's parallel port connector.

1.Find an empty slot in your chassis.

2.Unscrew the plate that covers the end of the slot.

3.Screw in the bracket in place of the plate.

4.Next, attach the flat-cable connector to the PRINTER connec- tor. Wire 1 of the cable is red or blue, and the other wires are gray. Make sure that Wire 1 connects to Pin 1 of the PRINTER connector. Pin 1 is on the right side of the PRINTER connec- tor.

Pin assignments

PRINTER Connector

Pin

Signal

Pin

Signal

1

Strobe

2

Data 0

 

 

 

 

3

Data 1

4

Data 2

 

 

 

 

5

Data 3

6

Data 4

 

 

 

 

7

Data 5

8

Data 6

9

Data 7

10

-Acknowledge

 

 

 

 

11

Busy

12

Paper empty

 

 

 

 

13

+ Select

14

- Auto feed

 

 

 

 

15

- Error

16

- Init printer

17

- Select input

18~25

GND

 

 

 

 

Chapter 2 Installation 21

Page 28 Page 30
Image 29
Page 28 Page 30
Contents Page FCC Statement Acknowledgements Copyright NoticePacking list Contents Keyboard and PS/2 KB/ mouse connections Chpater 4 Flat Panel/CRT Controller Display Drivers Page General Information Introduction Features Specifications Bus speed 8 MHz P 6 8 T 8 4 M Board layoutCard dimensions Page Installation Label Function Jumpers and connectorsLocating jumpers and connectors Setting jumpers Removing a CPU Safety precautionsInstalling the CPU Installing a CPU CPU Type select JP4, JP3, JP1 CPU type select JP1, JP3, JP4CPU clock select JP9, JP10 CPU Vcc select JP2Removing SIMMs Installing Dram SIMMsInstalling SIMMs IDE hard drive connections IDE Connecting the hard driveIDE LED IDE LED Floppy drive connections Floppy Disk Connecting the floppy driveParallel port Printer Installing the retaining bracketParallel port DRQ and Dack JP11 Power supply connections Power CONPower supply connector Display connections VGA, LCD LCD signal select JP5, JP7 Keyboard and PS/2 KB/ mouse connections KB CON, KB/PS2 Mouse RS-232 connections COM A, COM B Serial portsSerial ports IRQ select JP11 Watchdog timer programming Watchdog timer setupWatchdog timer time-out signal select JP6 Delay time Value Hex External speaker EXT SPK External switches and LEDsPower LED and keylock KEY Lock Turbo LED Turbo LED Reset switch Reset SWClear Cmos JP12 SMI System Management Interrupt switch SMI SWTurbo Switch Turbo SW Flash Bios Write-enable Voltage JP13 Flash Bios Protect JP8Page AMI WinBIOS Setup WinBIOS main menu Starting WinBIOS setupUsing the keyboard with WinBIOS setup Using a mouse with WinBIOS setupStandard Setup SetupFloppy A, Floppy B Advanced Setup Setting Description Turbo Switch Press F1 to continue SettingDescription Execution Function Options Chipset SetupFast Power Management Setup PCI/PnP Setup PCI Latency Timer in PCI Clocks IRQ3 IRQ4 IRQ5 IRQ7 IRQ9 IRQ10 IRQ11 IRQ12 IRQ14 IRQ15 Reserved Memory Size Peripheral Setup EPP Parallel Port DMA Channel Utility Security Following screen appears when you select the password icon Changing a password Default Exiting WinBIOS Page Flat Panel/CRT Controller Display Driv- ersandUtilities Software drivers Hardware configurationBefore you begin Necessary prerequisitesWindowsÔ Driver installationWindows Ô Driver installation Windows SetupDOS VGA OS/2OS/2 Diskette copies of the OS/2 drivers must have a Windows Ô NT Windows NT Chipsdsp utility program Software UtilitiesFlat Panel/ CRT Controller Chipscpl utility program Installing the utilityHow to use the utility Flat Panel/ CRT Controller Page Watchdog Timer Demo Program Dog=dog/2 End=clock Page Installing PC/104 Modules PCM-3660 Mount the PC/104 module onto the CPU card. Do this PC/104 module dimensions inches ±5% LCD Display Bios Configuration Configuring various LCD display Appendix C LCD Display Bios Configuration C-89
Top Page Image Contents