Intel SBC-455 manual FCC Statement

Page 2

FCC STATEMENT

THIS DEVICE COMPLIES WITH PART 15 FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE. (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPER- ATION.

THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS FOR A CLASS "A" DIGITAL DEVICE, PURSUANT TO PART 15 OF THE FCC RULES. THESE LIMITS ARE DESIGNED TO PROVIDE REASONABLE PROTECTION AGAINTST HARMFUL INTERFERENCE WHEN THE EQUIPMENT IS OPERATED IN A COMMERCIAL ENVIRONMENT.

THIS EQUIPMENT GENERATES, USES, AND CAN RADIATE RADIO FREQENCY ENERGY AND , IF NOT INSTATLLED AND USED IN ACCORDANCE WITH THE INSTRUCTION MANUAL, MAY CAUSE HARMFUL INTERFERENCE TO RADIO COMMUNICATIONS. OPERATION OF THIS EQUIPMENT IN A RESIDEN- TIAL AREA IS LIKELY TO CAUSE HARMFUL INTER- FERENCE IN WHICH CASE THE USER WILL BE REQUIRED TO CORRECT THE INTERFERENCE AT HIS OWN EXPENSE.

Image 2

Contents Page FCC Statement Copyright Notice AcknowledgementsPacking list Contents Keyboard and PS/2 KB/ mouse connections Chpater 4 Flat Panel/CRT Controller Display Drivers Page General Information Introduction Features Specifications Bus speed 8 MHz Board layout P 6 8 T 8 4 MCard dimensions Page Installation Jumpers and connectors Label FunctionLocating jumpers and connectors Setting jumpers Removing a CPU Safety precautionsInstalling the CPU Installing a CPU CPU type select JP1, JP3, JP4 CPU Type select JP4, JP3, JP1CPU Vcc select JP2 CPU clock select JP9, JP10Removing SIMMs Installing Dram SIMMsInstalling SIMMs Connecting the hard drive IDE hard drive connections IDEIDE LED IDE LED Connecting the floppy drive Floppy drive connections Floppy DiskInstalling the retaining bracket Parallel port PrinterParallel port DRQ and Dack JP11 Power supply connections Power CONPower supply connector Display connections VGA, LCD LCD signal select JP5, JP7 Keyboard and PS/2 KB/ mouse connections KB CON, KB/PS2 Mouse Serial ports RS-232 connections COM A, COM BSerial ports IRQ select JP11 Watchdog timer programming Watchdog timer setupWatchdog timer time-out signal select JP6 Delay time Value Hex External speaker EXT SPK External switches and LEDsPower LED and keylock KEY Lock Reset switch Reset SW Turbo LED Turbo LEDClear Cmos JP12 SMI System Management Interrupt switch SMI SWTurbo Switch Turbo SW Flash Bios Protect JP8 Flash Bios Write-enable Voltage JP13Page AMI WinBIOS Setup Starting WinBIOS setup WinBIOS main menuUsing a mouse with WinBIOS setup Using the keyboard with WinBIOS setupSetup Standard SetupFloppy A, Floppy B Advanced Setup Setting Description Turbo Switch Press F1 to continue SettingDescription Execution Chipset Setup Function OptionsFast Power Management Setup PCI/PnP Setup PCI Latency Timer in PCI Clocks IRQ3 IRQ4 IRQ5 IRQ7 IRQ9 IRQ10 IRQ11 IRQ12 IRQ14 IRQ15 Reserved Memory Size Peripheral Setup EPP Parallel Port DMA Channel Utility Security Following screen appears when you select the password icon Changing a password Default Exiting WinBIOS Page Flat Panel/CRT Controller Display Driv- ersandUtilities Hardware configuration Software driversNecessary prerequisites Before you beginDriver installation WindowsÔDriver installation Windows Setup Windows ÔDOS OS/2 VGAOS/2 Diskette copies of the OS/2 drivers must have a Windows Ô NT Windows NT Software Utilities Chipsdsp utility programFlat Panel/ CRT Controller Chipscpl utility program Installing the utilityHow to use the utility Flat Panel/ CRT Controller Page Watchdog Timer Demo Program Dog=dog/2 End=clock Page Installing PC/104 Modules PCM-3660 Mount the PC/104 module onto the CPU card. Do this PC/104 module dimensions inches ±5% LCD Display Bios Configuration Configuring various LCD display Appendix C LCD Display Bios Configuration C-89