Intel SBC-455 manual Software Utilities, Chipsdsp utility program

Page 82

SOFTWARE UTILITIES

This chapter describes the operation and installation of the following software utilities supplied on the Display Driver Diskettes:

•CHIPSDSP

•CHIPSCPL

The CHIPSDSP utility program

This utility program is designed to work with MicrosoftÒ WindowsÔ 95.

Installing the utility

CHIPSDSP.DLL is located on the CHIPS WindowsÔ 95 driver disk. This file is a WinsowsÔ 95 based utility for selecting display type and refresh rate. It is a Display Properties Refresh window that is automatically installed when installling CHIPS WindowsÔ 95 dis- play drivers. The Display icon is in the Control Panel group. To invoke the Display icon, simply click on the Start button, go to Set- tings, click on Control Panel, and then double click on the Display icon. Click on the property sheet with the heading Refresh.

How to use the utility

DISPLAY DEVICE allows you to select the display type from the following:

• CRT Only		<ALT C>
•	LCD (Flat Panel) only	<ALT I >
•	Both CRT and LCD (Flat Panel)	<ALT B>

74 PCM-5890 User's Manual

Image 82

Contents Page FCC Statement Copyright Notice AcknowledgementsPacking list Contents Keyboard and PS/2 KB/ mouse connections Chpater 4 Flat Panel/CRT Controller Display Drivers Page General Information Introduction Features Specifications Bus speed 8 MHz Board layout P 6 8 T 8 4 MCard dimensions Page Installation Jumpers and connectors Label FunctionLocating jumpers and connectors Setting jumpers Installing the CPU Safety precautionsRemoving a CPU Installing a CPU CPU type select JP1, JP3, JP4 CPU Type select JP4, JP3, JP1CPU Vcc select JP2 CPU clock select JP9, JP10Installing SIMMs Installing Dram SIMMsRemoving SIMMs Connecting the hard drive IDE hard drive connections IDEIDE LED IDE LED Connecting the floppy drive Floppy drive connections Floppy DiskInstalling the retaining bracket Parallel port PrinterPower supply connector Power supply connections Power CONParallel port DRQ and Dack JP11 Display connections VGA, LCD LCD signal select JP5, JP7 Keyboard and PS/2 KB/ mouse connections KB CON, KB/PS2 Mouse Serial ports RS-232 connections COM A, COM BSerial ports IRQ select JP11 Watchdog timer time-out signal select JP6 Watchdog timer setupWatchdog timer programming Delay time Value Hex Power LED and keylock KEY Lock External switches and LEDsExternal speaker EXT SPK Reset switch Reset SW Turbo LED Turbo LEDTurbo Switch Turbo SW SMI System Management Interrupt switch SMI SWClear Cmos JP12 Flash Bios Protect JP8 Flash Bios Write-enable Voltage JP13Page AMI WinBIOS Setup Starting WinBIOS setup WinBIOS main menuUsing a mouse with WinBIOS setup Using the keyboard with WinBIOS setupSetup Standard SetupFloppy A, Floppy B Advanced Setup Setting Description Turbo Switch Press F1 to continue SettingDescription Execution Chipset Setup Function OptionsFast Power Management Setup PCI/PnP Setup PCI Latency Timer in PCI Clocks IRQ3 IRQ4 IRQ5 IRQ7 IRQ9 IRQ10 IRQ11 IRQ12 IRQ14 IRQ15 Reserved Memory Size Peripheral Setup EPP Parallel Port DMA Channel Utility Security Following screen appears when you select the password icon Changing a password Default Exiting WinBIOS Page Flat Panel/CRT Controller Display Driv- ersandUtilities Hardware configuration Software driversNecessary prerequisites Before you beginDriver installation WindowsÔDriver installation Windows Setup Windows ÔDOS OS/2 VGAOS/2 Diskette copies of the OS/2 drivers must have a Windows Ô NT Windows NT Software Utilities Chipsdsp utility programFlat Panel/ CRT Controller How to use the utility Installing the utilityChipscpl utility program Flat Panel/ CRT Controller Page Watchdog Timer Demo Program Dog=dog/2 End=clock Page Installing PC/104 Modules PCM-3660 Mount the PC/104 module onto the CPU card. Do this PC/104 module dimensions inches ±5% LCD Display Bios Configuration Configuring various LCD display Appendix C LCD Display Bios Configuration C-89