Intel SBC-455 manual OS/2

Page 78

2.Place the OS/2 Display Driver Diskette in drive A. Type

A:<ENTER> to make this the default drive. Then type INST2X

A:C: <ENTER> (for OS/2 2.1x systems) or INST30 A: C: <ENTER> (for OS/2 Version 3 systems). Once the Install Program is completed, do a system shutdown and reboot.

3.After the system has rebooted, follow these instructions:

A) OS/2 2.1x

Open an OS/2 full-screen or windowed session. At the OS/2 prompt, type DSPINSTL <ENTER> to install the new device driver and configure the video system.

B) OS/2 Version 3

Go to the System Setup folder and run Selective Install to install the new device driver and configure the video system.

Follow the instructions of the program to set up the OS/2 drivers in your system. First, select Primary Display. From the list of Primary Display Adapter Types, select Chips and Technologies 655XX.

From the list of available Display Resolutions, select a display resolution. The correct source directory must be specified. Once the installation is complete, the system must be shut down and restarted for changes to take effect.

WIN-OS/2

Please note the following limitations regarding WIN-OS/2.

1.The WIN-OS/2 full screen session should be set to Enhanced Capability. The default setting is Standard Mode. If this setting is not changed, Windows will not run.

2.WIN-OS/2 should be started by selecting the WIN-OS/2 Full Screen Icon in the Command Prompts folder, or with the WIN command in a DOS Full Screen or OS/2 Full Screen session.

3.Do not start WIN-OS/2 in a DOS or OS/2 Window. The system does not support the enhanced video mode being used in a window, and therefore will not run.

70 PCM-5890 User's Manual

Image 78

Contents Page FCC Statement Copyright Notice AcknowledgementsPacking list Contents Keyboard and PS/2 KB/ mouse connections Chpater 4 Flat Panel/CRT Controller Display Drivers Page General Information Introduction Features Specifications Bus speed 8 MHz Board layout P 6 8 T 8 4 MCard dimensions Page Installation Jumpers and connectors Label FunctionLocating jumpers and connectors Setting jumpers Safety precautions Installing the CPURemoving a CPU Installing a CPU CPU type select JP1, JP3, JP4 CPU Type select JP4, JP3, JP1CPU Vcc select JP2 CPU clock select JP9, JP10Installing Dram SIMMs Installing SIMMsRemoving SIMMs Connecting the hard drive IDE hard drive connections IDEIDE LED IDE LED Connecting the floppy drive Floppy drive connections Floppy DiskInstalling the retaining bracket Parallel port PrinterPower supply connections Power CON Power supply connectorParallel port DRQ and Dack JP11 Display connections VGA, LCD LCD signal select JP5, JP7 Keyboard and PS/2 KB/ mouse connections KB CON, KB/PS2 Mouse Serial ports RS-232 connections COM A, COM BSerial ports IRQ select JP11 Watchdog timer setup Watchdog timer time-out signal select JP6Watchdog timer programming Delay time Value Hex External switches and LEDs Power LED and keylock KEY LockExternal speaker EXT SPK Reset switch Reset SW Turbo LED Turbo LEDSMI System Management Interrupt switch SMI SW Turbo Switch Turbo SWClear Cmos JP12 Flash Bios Protect JP8 Flash Bios Write-enable Voltage JP13Page AMI WinBIOS Setup Starting WinBIOS setup WinBIOS main menuUsing a mouse with WinBIOS setup Using the keyboard with WinBIOS setupSetup Standard SetupFloppy A, Floppy B Advanced Setup Setting Description Turbo Switch Press F1 to continue SettingDescription Execution Chipset Setup Function OptionsFast Power Management Setup PCI/PnP Setup PCI Latency Timer in PCI Clocks IRQ3 IRQ4 IRQ5 IRQ7 IRQ9 IRQ10 IRQ11 IRQ12 IRQ14 IRQ15 Reserved Memory Size Peripheral Setup EPP Parallel Port DMA Channel Utility Security Following screen appears when you select the password icon Changing a password Default Exiting WinBIOS Page Flat Panel/CRT Controller Display Driv- ersandUtilities Hardware configuration Software driversNecessary prerequisites Before you beginDriver installation WindowsÔDriver installation Windows Setup Windows ÔDOS OS/2 VGAOS/2 Diskette copies of the OS/2 drivers must have a Windows Ô NT Windows NT Software Utilities Chipsdsp utility programFlat Panel/ CRT Controller Installing the utility How to use the utilityChipscpl utility program Flat Panel/ CRT Controller Page Watchdog Timer Demo Program Dog=dog/2 End=clock Page Installing PC/104 Modules PCM-3660 Mount the PC/104 module onto the CPU card. Do this PC/104 module dimensions inches ±5% LCD Display Bios Configuration Configuring various LCD display Appendix C LCD Display Bios Configuration C-89