Intel SBC-455 manual Diskette copies of the OS/2 drivers must have a

Page 79

4.When running WIN-OS/2, DO NOT use <ALT>+<HOME> to switch a DOS or OS/2 Full Screen session to Windows. If this happens, do a system shutdown and reboot.

Driver diskette copy

NOTE:	Diskette copies of the OS/2 drivers must have a
	VOLUME LABEL that reads “DISP 1” in order to be
	an installable diskette.

To copy the OS/2 Display Driver Diskette, follow these instruc- tions:

1.Copy all files on the OS/2 Display Driver Diskette as you normally would onto another diskette.

2.Place the diskette copy in drive A. At the C:\ prompt, type LABEL A: DISP 1 to properly label your diskette. Then store your diskette copy in a safe place.

For proper installation of OS/2 drivers, all diskette copies must be properly labeled “DISP 1”.

Chapter 5 Flat Panel/ CRT Controller 71

Image 79

Contents Page FCC Statement Acknowledgements Copyright NoticePacking list Contents Keyboard and PS/2 KB/ mouse connections Chpater 4 Flat Panel/CRT Controller Display Drivers Page General Information Introduction Features Specifications Bus speed 8 MHz P 6 8 T 8 4 M Board layoutCard dimensions Page Installation Label Function Jumpers and connectorsLocating jumpers and connectors Setting jumpers Installing the CPU Safety precautionsRemoving a CPU Installing a CPU CPU Type select JP4, JP3, JP1 CPU type select JP1, JP3, JP4CPU clock select JP9, JP10 CPU Vcc select JP2Installing SIMMs Installing Dram SIMMsRemoving SIMMs IDE hard drive connections IDE Connecting the hard driveIDE LED IDE LED Floppy drive connections Floppy Disk Connecting the floppy driveParallel port Printer Installing the retaining bracketPower supply connector Power supply connections Power CONParallel port DRQ and Dack JP11 Display connections VGA, LCD LCD signal select JP5, JP7 Keyboard and PS/2 KB/ mouse connections KB CON, KB/PS2 Mouse RS-232 connections COM A, COM B Serial portsSerial ports IRQ select JP11 Watchdog timer time-out signal select JP6 Watchdog timer setupWatchdog timer programming Delay time Value Hex Power LED and keylock KEY Lock External switches and LEDsExternal speaker EXT SPK Turbo LED Turbo LED Reset switch Reset SWTurbo Switch Turbo SW SMI System Management Interrupt switch SMI SWClear Cmos JP12 Flash Bios Write-enable Voltage JP13 Flash Bios Protect JP8Page AMI WinBIOS Setup WinBIOS main menu Starting WinBIOS setupUsing the keyboard with WinBIOS setup Using a mouse with WinBIOS setupStandard Setup SetupFloppy A, Floppy B Advanced Setup Setting Description Turbo Switch Press F1 to continue SettingDescription Execution Function Options Chipset SetupFast Power Management Setup PCI/PnP Setup PCI Latency Timer in PCI Clocks IRQ3 IRQ4 IRQ5 IRQ7 IRQ9 IRQ10 IRQ11 IRQ12 IRQ14 IRQ15 Reserved Memory Size Peripheral Setup EPP Parallel Port DMA Channel Utility Security Following screen appears when you select the password icon Changing a password Default Exiting WinBIOS Page Flat Panel/CRT Controller Display Driv- ersandUtilities Software drivers Hardware configurationBefore you begin Necessary prerequisitesWindowsÔ Driver installationWindows Ô Driver installation Windows SetupDOS VGA OS/2OS/2 Diskette copies of the OS/2 drivers must have a Windows Ô NT Windows NT Chipsdsp utility program Software UtilitiesFlat Panel/ CRT Controller How to use the utility Installing the utilityChipscpl utility program Flat Panel/ CRT Controller Page Watchdog Timer Demo Program Dog=dog/2 End=clock Page Installing PC/104 Modules PCM-3660 Mount the PC/104 module onto the CPU card. Do this PC/104 module dimensions inches ±5% LCD Display Bios Configuration Configuring various LCD display Appendix C LCD Display Bios Configuration C-89