ViewSonic PJ758/PJ759/PJ760 manual Searching an input signal, Selecting an aspect ratio

Page 22

Operating

Selecting an input signal (continued)

VIDEO

1. Press VIDEO button on the remote control.

Each time you press the button, the projector switches its input port as below.

VIDEO COMPUTER SEARCH

ASPECT

AUTO BLANK

COMPONENT(Y, Cb/Pb, Cr/Pr) Æ S-VIDEO Æ VIDEO

MAGNIFY

HOME

PAGE UP VOLUME

ON

 

OFF

END

PAGE DOWN

MUTE

● If VIDEO button is pushed to switch from a signal from

FREEZE

MY BUTTON

KEYSTONE

 

1

2

 

COMPUTER IN1 or 2 port, when TURN ON is selected for AUTO POSITION

 

 

MENU

SEARCH item in OPTION menu ( 40), the projector will check COMPONENT port first. If no input is detected at the port, the projector will check the other port in above order.

Searching an input signal

1. Press SEARCH button on the remote control.

The projector will start to check its input ports in order to find any input signals.

When an input is found, the projector will stop searching and display the image. If no signal is found, the projector will return to the state selected before the operation.

COMPUTER IN 1 Æ COMPUTER IN 2

VIDEO Æ S-VIDEO Æ COMPONENT (Y, Cb/Pb, Cr/Pr)

SEARCH

VIDEO

COMPUTER SEARCH

 

ASPECT

 

AUTO

BLANK

MAGNIFY

HOME

PAGE UP

VOLUME

ON

 

 

 

OFF

END

PAGE DOWN

MUTE

 

 

 

FREEZE

MY BUTTON

KEYSTONE

12

POSITIONMENU

Selecting an aspect ratio

1. Press ASPECT button on the remote control.

Each time you press the button, the projector switches the mode for aspect ratio in turn.

€For a computer signal

NORMAL Æ 4:3 Æ 16:9 Æ SMALL

€For a video signal, s-video signal or component video signal

4:3 Æ 16:9 Æ 14:9 Æ SMALL

€For no signal 4:3 (fixed)

ASPECT

VIDEO

COMPUTER SEARCH

 

ASPECT

 

AUTO

BLANK

MAGNIFY

HOME

PAGE UP

VOLUME

ON

 

 

 

OFF

END

PAGE DOWN

MUTE

 

 

 

FREEZE

MY BUTTON

KEYSTONE

12

POSITIONMENU

ASPECT button does not work when no proper signal is inputted.

NORMAL mode keeps the original aspect ratio setting.

ViewSonic

17

PJ758/PJ759/PJ760

Image 22
Contents ViewSonic CE Conformity for European Countries FCC StatementFor Canada Following information is only for EU-member statesImportant Safety Instructions Declaration of RoHS Compliance Copyright Information Serial Number Purchase DateThank you for purchasing this projector About this manualTrademark acknowledgment Content Contents of package Fastening the lens coverProjector Part namesHOT Rear panel Control panelComponent Remote control Battery coverPJ758/PJ760 Setting upArrangement On a horizontal surface Suspended from the ceilingArrangement PJ759Setting up Speakers Connecting your devicesMonitor VCR/DVD playerConnecting your devices About Plug-and-Play capabilityConnecting power supply Using the security bar and slotAbout the remote control signal Remote controlPutting batteries Mouse right button Press Reset button Changing the frequency of remote control signalUsing as a simple PC mouse & keyboard Mouse left button Press Enter buttonTurning on the power Power on/offTurning off the power Operating Adjusting the volumeSelecting an input signal Temporarily muting the sound€ For a computer signal Searching an input signalSelecting an input signal € For no signal 43 fixedAdjusting the projectors elevator Adjusting the zoom and focusAuto Using the automatic adjustment featureAdjusting the position PositionKeystone Using the magnify featureCorrecting the keystone distortions Magnify ON/OFFFreeze Freezing the screenTemporarily blanking the screen BlankUsing the menu function Using the menu function Advanced MenuAuto Picture ModeAspect KeystoneEasy Menu Gamma Picture MenuColor Temp SAVE-4 ÙSAVE-3 Ù SAVE-2 Ù SAVE-1 Picture MenuLOAD-1 Ù LOAD-2 Ù LOAD-3 Ù LOAD-4 LOAD-1, LOAD-2, LOAD-3, LOAD-4For adjusting Color Temp To adjust Custom function in Gamma and Color TempFor adjusting Gamma Gamma Color TempImage Menu For a computer signalFor no signal Over ScanImage Menu PhaseAuto Adjust SizeVideo NR Input MenuProgressive Color SpaceFrame Lock Input MenuVideo Format ComputerCustom ResolutionStandard Standard CustomSetup Menu Speaker Setup MenuVolume AudioScreen Menu BlankScreen Menu Start UPMyScreen Capturing error has occurred. Please try againMyScreen registration is finished Message No Input is DetectedSync is OUT of Range Source NameComputer IN1 Ö Computer IN2 Option MenuAuto Search Video Õ S-VIDEO Õ ComponentAuto OFF Reset Õ CancelOption Menu Lamp TimeMY Button ServiceFAN Speed Ghost Fine Ù Fast Ù DisableFilter Message Remote Freq Factory ResetKEY Lock 1NORMAL Ù 2HIGHChanging the Password Using Security FeaturesInputting the Password SecurityTurning on the MyScreen Password Function Using the MyScreen Password FunctionIf you have forgotten your Password Setting the PasswordTurning the Password off Using the PIN Lock FunctionRegistering the PIN Code Turning Off the PIN Lock Function If you have forgotten your PIN CodeSetting the Transition Detector Password Using the Transition Detector FunctionTurning On the Transition Detector Function Setting the Transition Detector off Lamp MaintenanceType number RLC-031 Replacing the lamp Lamp warning LampCleaning the air filter Air filterInside of the projector Caring for the cabinet and remote controlOther care Caring for the lensInternal temperature is rising TroubleshootingThere is no input signal Related messagesRegarding the indicator lamps Resetting all settings Shutting the projector downSignal source does not correctly work Electrical power cord is not pluggedSignal cables are not correctly connected Input changeover settings are mismatchedNot properly adjusted Color settings are not correctly adjustedColor Space setting is not suitable Play monitorSpecification SpecificationsSpecification Specifications Customer Support Who the warranty protects What the warranty coversHow long the warranty is effective What the warranty does not coverEffect of state law Limitation of implied warrantiesExclusion of damages Sales outside the U.S.A. and Canada