ViewSonic PJ758/PJ759/PJ760 manual Part names, Projector, Hot

Page 9

Part names

Part names

Projector

(1)

Lamp cover (

51)

 

The lamp unit is inside.

(2)

Focus ring (

18)

 

(3)

Zoom ring (

18)

5)

(4)

Control panel (

(5)

Elevator buttons (x 2) ( 18)

(6)

Elevator feet

(x 2) ( 18)

(7)

Remote sensor (

13)

(8)

Lens ( 18, 54)

 

(9)

Lens cover (

3)

 

(10) Intake vents

53)

(11) Filter cover (

The air filter and intake vent are inside.

(12)Speaker ( 35)

(13)Exhaust vent

(14) AC inlet ( 12)

15)

(15)

Power switch (

(16)

Rear panel (

5)

(17)

Security bar (

12)

(18)

Security slot (

12)

HOT! (1)

(6)

(8)

(9)

(6)

HOT! (13)

(4)

(18)

(16)

(17)

(2) (3) (4)

(11)

(5) (10)

(7)(6)

(6)

(10)

(11)

(12)

(14)

(15)

(1)

(13)

WARNING HOT! : Do not touch around the lamp cover and the exhaust

vents during use or just after use, since it is too hot.

►Do not look into the lens or vents while the lamp is on, since the strong light is not good for your eyes.

►Do not handle the elevator buttons without holding the projector, since the projector may drop down.

CAUTION ►Maintain normal ventilation to prevent the projector from heating up. Do not cover, block or plug up the vents. Do not place anything that can stick or be sucked to the vents, around the intake vents. Clean the air filter periodically.

ViewSonic

4

PJ758/PJ759/PJ760

Image 9
Contents ViewSonic For Canada FCC StatementCE Conformity for European Countries Following information is only for EU-member statesImportant Safety Instructions Declaration of RoHS Compliance Serial Number Purchase Date Copyright InformationAbout this manual Thank you for purchasing this projectorTrademark acknowledgment Content Fastening the lens cover Contents of packagePart names ProjectorHOT Control panel Rear panelComponent Battery cover Remote controlArrangement Setting upPJ758/PJ760 On a horizontal surface Suspended from the ceilingPJ759 ArrangementSetting up Monitor Connecting your devicesSpeakers VCR/DVD playerAbout Plug-and-Play capability Connecting your devicesUsing the security bar and slot Connecting power supplyRemote control About the remote control signalPutting batteries Using as a simple PC mouse & keyboard Changing the frequency of remote control signalMouse right button Press Reset button Mouse left button Press Enter buttonPower on/off Turning on the powerTurning off the power Selecting an input signal Adjusting the volumeOperating Temporarily muting the soundSelecting an input signal Searching an input signal€ For a computer signal € For no signal 43 fixedAdjusting the zoom and focus Adjusting the projectors elevatorAdjusting the position Using the automatic adjustment featureAuto PositionCorrecting the keystone distortions Using the magnify featureKeystone Magnify ON/OFFTemporarily blanking the screen Freezing the screenFreeze BlankUsing the menu function Advanced Menu Using the menu functionAspect Picture ModeAuto KeystoneEasy Menu Picture Menu GammaColor Temp LOAD-1 Ù LOAD-2 Ù LOAD-3 Ù LOAD-4 Picture MenuSAVE-4 ÙSAVE-3 Ù SAVE-2 Ù SAVE-1 LOAD-1, LOAD-2, LOAD-3, LOAD-4For adjusting Gamma To adjust Custom function in Gamma and Color TempFor adjusting Color Temp Gamma Color TempFor no signal For a computer signalImage Menu Over ScanAuto Adjust PhaseImage Menu SizeProgressive Input MenuVideo NR Color SpaceVideo Format Input MenuFrame Lock ComputerStandard ResolutionCustom Standard CustomSetup Menu Volume Setup MenuSpeaker AudioBlank Screen MenuStart UP Screen MenuCapturing error has occurred. Please try again MyScreenMyScreen registration is finished Sync is OUT of Range No Input is DetectedMessage Source NameAuto Search Option MenuComputer IN1 Ö Computer IN2 Video Õ S-VIDEO Õ ComponentOption Menu Reset Õ CancelAuto OFF Lamp TimeService MY ButtonFAN Speed Fine Ù Fast Ù Disable GhostFilter Message KEY Lock Factory ResetRemote Freq 1NORMAL Ù 2HIGHInputting the Password Using Security FeaturesChanging the Password SecurityIf you have forgotten your Password Using the MyScreen Password FunctionTurning on the MyScreen Password Function Setting the PasswordUsing the PIN Lock Function Turning the Password offRegistering the PIN Code If you have forgotten your PIN Code Turning Off the PIN Lock FunctionUsing the Transition Detector Function Setting the Transition Detector PasswordTurning On the Transition Detector Function Setting the Transition Detector off Maintenance LampType number RLC-031 Replacing the lamp Lamp Lamp warningAir filter Cleaning the air filterOther care Caring for the cabinet and remote controlInside of the projector Caring for the lensThere is no input signal TroubleshootingInternal temperature is rising Related messagesRegarding the indicator lamps Shutting the projector down Resetting all settingsSignal cables are not correctly connected Electrical power cord is not pluggedSignal source does not correctly work Input changeover settings are mismatchedColor Space setting is not suitable Color settings are not correctly adjustedNot properly adjusted Play monitorSpecifications SpecificationSpecification Specifications Customer Support How long the warranty is effective What the warranty coversWho the warranty protects What the warranty does not coverExclusion of damages Limitation of implied warrantiesEffect of state law Sales outside the U.S.A. and Canada