ViewSonic PJ758/PJ759/PJ760 manual Maintenance, Lamp, Type number RLC-031 Replacing the lamp

Page 56

Maintenance

Maintenance

Lamp

A lamp has ﬁnite product life. Using the lamp for long periods of time could cause the pictures darker or the color tone poor. Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them. Preparation of a new lamp and early replacement are recommended. To prepare a new lamp, contact your dealer and tell the lamp type number.

Type number : RLC-031

Replacing the lamp

1. Turn the projector off, and unplug the power cord. Allow the projector to cool for at least 45 minutes.

2. Prepare a new lamp.

If the projector is mounted on a ceiling, or if the lamp has broken, also ask the dealer to replace the lamp.

In case of replacement by yourself, follow the following procedure.

3. Loosen the screw (marked by arrow) of the lamp cover and then slide the lamp cover to the side to remove it.

4. Loosen the 2 screws (marked by arrow) of the lamp, and slowly pick up the lamp by the handles.

5. Insert the new lamp, and retighten ﬁrmly the 2 screws of the lamp that are loosened in the

previous process to lock it in place.

6. Slide the lamp cover back in place and ﬁrmly fasten the screw of the lamp cover.

Lamp cover

Handles

7. Turn the projector on and reset the lamp time using the LAMP TIME item in the OPTION menu.

(1) Press the MENU button to display a menu.

(2)Point at the “Go to Advanced Menu …” in the menu using the ▼/▲ button, then press the ► button.

(3)Point at the “OPTION” in the left column of the menu using the ▼/▲button, then press the ► button.

(4)Point at the “LAMP TIME” using the ▼/▲ button, then press the ► button. A dialog will appear.

(5)Press the ▲ button to select “RESET” on the dialog. It performs resetting the lamp time.

CAUTION ►Do not touch any inner space of the projector, while the lamp is taken out.

NOTE • Please reset the lamp time only when you have replaced the lamp, for a suitable indication about the lamp.

ViewSonic

51

PJ758/PJ759/PJ760

Image 56

Contents ViewSonic FCC Statement For CanadaCE Conformity for European Countries Following information is only for EU-member statesImportant Safety Instructions Declaration of RoHS Compliance Copyright Information Serial Number Purchase DateTrademark acknowledgment About this manualThank you for purchasing this projector Content Contents of package Fastening the lens coverHOT Part namesProjector Component Control panelRear panel Remote control Battery coverSetting up ArrangementPJ758/PJ760 On a horizontal surface Suspended from the ceilingArrangement PJ759Setting up Connecting your devices MonitorSpeakers VCR/DVD playerConnecting your devices About Plug-and-Play capabilityConnecting power supply Using the security bar and slotPutting batteries Remote controlAbout the remote control signal Changing the frequency of remote control signal Using as a simple PC mouse & keyboardMouse right button Press Reset button Mouse left button Press Enter buttonTurning off the power Power on/offTurning on the power Adjusting the volume Selecting an input signalOperating Temporarily muting the soundSearching an input signal Selecting an input signal€ For a computer signal € For no signal 43 ﬁxedAdjusting the projectors elevator Adjusting the zoom and focusUsing the automatic adjustment feature Adjusting the positionAuto PositionUsing the magnify feature Correcting the keystone distortionsKeystone Magnify ON/OFFFreezing the screen Temporarily blanking the screenFreeze BlankUsing the menu function Using the menu function Advanced MenuPicture Mode AspectAuto KeystoneEasy Menu Color Temp Picture MenuGamma Picture Menu LOAD-1 Ù LOAD-2 Ù LOAD-3 Ù LOAD-4SAVE-4 ÙSAVE-3 Ù SAVE-2 Ù SAVE-1 LOAD-1, LOAD-2, LOAD-3, LOAD-4To adjust Custom function in Gamma and Color Temp For adjusting GammaFor adjusting Color Temp Gamma Color TempFor a computer signal For no signalImage Menu Over ScanPhase Auto AdjustImage Menu SizeInput Menu ProgressiveVideo NR Color SpaceInput Menu Video FormatFrame Lock ComputerResolution StandardCustom Standard CustomSetup Menu Setup Menu VolumeSpeaker AudioScreen Menu BlankScreen Menu Start UPMyScreen registration is ﬁnished Capturing error has occurred. Please try againMyScreen No Input is Detected Sync is OUT of RangeMessage Source NameOption Menu Auto SearchComputer IN1 Ö Computer IN2 Video Õ S-VIDEO Õ ComponentReset Õ Cancel Option MenuAuto OFF Lamp TimeFAN Speed ServiceMY Button Filter Message Fine Ù Fast Ù DisableGhost Factory Reset KEY LockRemote Freq 1NORMAL Ù 2HIGHUsing Security Features Inputting the PasswordChanging the Password SecurityUsing the MyScreen Password Function If you have forgotten your PasswordTurning on the MyScreen Password Function Setting the PasswordRegistering the PIN Code Using the PIN Lock FunctionTurning the Password off Turning Off the PIN Lock Function If you have forgotten your PIN CodeTurning On the Transition Detector Function Using the Transition Detector FunctionSetting the Transition Detector Password Setting the Transition Detector off Type number RLC-031 Replacing the lamp MaintenanceLamp Lamp warning LampCleaning the air ﬁlter Air ﬁlterCaring for the cabinet and remote control Other careInside of the projector Caring for the lensTroubleshooting There is no input signalInternal temperature is rising Related messagesRegarding the indicator lamps Resetting all settings Shutting the projector downElectrical power cord is not plugged Signal cables are not correctly connectedSignal source does not correctly work Input changeover settings are mismatchedColor settings are not correctly adjusted Color Space setting is not suitableNot properly adjusted Play monitorSpeciﬁcation SpeciﬁcationsSpeciﬁcation Speciﬁcations Customer Support What the warranty covers How long the warranty is effectiveWho the warranty protects What the warranty does not coverLimitation of implied warranties Exclusion of damagesEffect of state law Sales outside the U.S.A. and Canada