ViewSonic PJ758/PJ759/PJ760 manual Option Menu, Auto Search, Computer IN1 Ö Computer IN2, Auto on

Page 45

OPTION Menu

OPTION Menu

From the OPTION menu, items shown in the table below can be performed.

Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item, except for the items LAMP TIME and FILTER TIME. Then perform it according to the following table.

Item

Description

	Using the ▲/▼ buttons turns on/off the automatic signal search function.
	TURN ON Ù TURN OFF
	When the TURN ON is selected, detecting no signal automatically
	cycles through input ports in the following order. The search is
AUTO SEARCH	started from the current port. Then when an input is found, the
	projector will stop searching and display the image.
	COMPUTER IN1 Ö COMPUTER IN2
	VIDEO Õ S-VIDEO Õ COMPONENT

	Using the ▲/▼ buttons turns on/off the automatic keystone function.
	TURN ON Ù TURN OFF

		TURN ON : Automatic keystone distortion correction will be
		executed whenever changing the slant of the projector.
	AUTO	TURN OFF : This function is disabled. Please execute the AUTO
	KEYSTONE	KEYSTONE EXECUTE in the SETUP Menu for automatic
	KEYSTONE	keystone distortion correction.
		keystone distortion correction.

•When the projector is suspended from the ceiling this feature will not function properly so select the TURN OFF.

•This function will be unavailable when the Transition Detector is on ( 49).

	Using the ▲/▼ buttons turns on/off the AUTO ON function.
	TURN ON Ù TURN OFF
	When set to the TURN ON, the lamp in projector will be
	automatically turned on without the usual procedure ( 15), only
AUTO ON	when the projector is supplied with the power after the power was
AUTO ON	cut while the lamp was on.
	• This function does not work as long as the power has been
	supplied to the projector while the lamp is off.
	• After turning the lamp on by the AUTO ON function, if neither input
	nor operation is detected for about 30 minutes, the projector is
	turned off, even though the AUTO OFF function ( 41) is disabled.

(continued on next page)

ViewSonic

40

PJ758/PJ759/PJ760

Image 45

Contents ViewSonic For Canada FCC StatementCE Conformity for European Countries Following information is only for EU-member statesImportant Safety Instructions Declaration of RoHS Compliance Serial Number Purchase Date Copyright InformationAbout this manual Thank you for purchasing this projectorTrademark acknowledgment Content Fastening the lens cover Contents of packagePart names ProjectorHOT Control panel Rear panelComponent Battery cover Remote controlArrangement Setting upPJ758/PJ760 On a horizontal surface Suspended from the ceilingPJ759 ArrangementSetting up Monitor Connecting your devicesSpeakers VCR/DVD playerAbout Plug-and-Play capability Connecting your devicesUsing the security bar and slot Connecting power supplyRemote control About the remote control signalPutting batteries Using as a simple PC mouse & keyboard Changing the frequency of remote control signalMouse right button Press Reset button Mouse left button Press Enter buttonPower on/off Turning on the powerTurning off the power Selecting an input signal Adjusting the volumeOperating Temporarily muting the soundSelecting an input signal Searching an input signal€ For a computer signal € For no signal 43 ﬁxedAdjusting the zoom and focus Adjusting the projectors elevatorAdjusting the position Using the automatic adjustment featureAuto PositionCorrecting the keystone distortions Using the magnify featureKeystone Magnify ON/OFFTemporarily blanking the screen Freezing the screenFreeze BlankUsing the menu function Advanced Menu Using the menu functionAspect Picture ModeAuto KeystoneEasy Menu Picture Menu GammaColor Temp LOAD-1 Ù LOAD-2 Ù LOAD-3 Ù LOAD-4 Picture MenuSAVE-4 ÙSAVE-3 Ù SAVE-2 Ù SAVE-1 LOAD-1, LOAD-2, LOAD-3, LOAD-4For adjusting Gamma To adjust Custom function in Gamma and Color TempFor adjusting Color Temp Gamma Color TempFor no signal For a computer signalImage Menu Over ScanAuto Adjust PhaseImage Menu SizeProgressive Input MenuVideo NR Color SpaceVideo Format Input MenuFrame Lock ComputerStandard ResolutionCustom Standard CustomSetup Menu Volume Setup MenuSpeaker AudioBlank Screen MenuStart UP Screen MenuCapturing error has occurred. Please try again MyScreenMyScreen registration is ﬁnished Sync is OUT of Range No Input is DetectedMessage Source NameAuto Search Option MenuComputer IN1 Ö Computer IN2 Video Õ S-VIDEO Õ ComponentOption Menu Reset Õ CancelAuto OFF Lamp TimeService MY ButtonFAN Speed Fine Ù Fast Ù Disable GhostFilter Message KEY Lock Factory ResetRemote Freq 1NORMAL Ù 2HIGHInputting the Password Using Security FeaturesChanging the Password SecurityIf you have forgotten your Password Using the MyScreen Password FunctionTurning on the MyScreen Password Function Setting the PasswordUsing the PIN Lock Function Turning the Password offRegistering the PIN Code If you have forgotten your PIN Code Turning Off the PIN Lock FunctionUsing the Transition Detector Function Setting the Transition Detector PasswordTurning On the Transition Detector Function Setting the Transition Detector off Maintenance LampType number RLC-031 Replacing the lamp Lamp Lamp warningAir ﬁlter Cleaning the air ﬁlterOther care Caring for the cabinet and remote controlInside of the projector Caring for the lensThere is no input signal TroubleshootingInternal temperature is rising Related messagesRegarding the indicator lamps Shutting the projector down Resetting all settingsSignal cables are not correctly connected Electrical power cord is not pluggedSignal source does not correctly work Input changeover settings are mismatchedColor Space setting is not suitable Color settings are not correctly adjustedNot properly adjusted Play monitorSpeciﬁcations SpeciﬁcationSpeciﬁcation Speciﬁcations Customer Support How long the warranty is effective What the warranty coversWho the warranty protects What the warranty does not coverExclusion of damages Limitation of implied warrantiesEffect of state law Sales outside the U.S.A. and Canada