ViewSonic PJ758/PJ759/PJ760 manual Shutting the projector down, Resetting all settings

Page 62

Troubleshooting

Regarding the indicator lamps (continued)

POWER

LAMP

TEMP

Description

indicator

indicator

indicator

 

 

 

 

 

 

 

 

There is a possibility that the interior portion

 

 

 

has become heated.

 

 

 

Please turn the power off, and allow the projector to cool down at least

Blinking

 

 

20 minutes. After the projector has sufficiently cooled down, please make

In Red

Turned

Lighting

confirmation of the following items, and then turn the power on again.

or

• Is there blockage of the air passage aperture?

Lighting

off

In Red

• Is the air filter dirty?

In Red

 

 

• Does the peripheral temperature exceed 35°C?

 

 

 

If the same indication is displayed after the remedy, please

 

 

 

set FAN SPEED of SERVICE item in OPTION menu to HIGH

 

 

 

( 42).

 

 

 

It is time to clean the air filter.

Lighting

Simultaneous

Please immediately turn the power off, and clean or change

the air filter referring to the section “Air Filter”. After cleaning or

In Green

blinking in Red

changing the air filter, please be sure to reset the filter timer.

 

 

 

 

 

 

After the remedy, reset the power to ON.

 

 

 

There is a possibility that the interior portion

Lighting

Alternative

has become overcooled.

Please use the unit within the usage temperature

In Green

blinking in Red

parameters (5°C to 35°C).

 

 

 

 

 

 

After the treatment, reset the power to ON.

NOTE • When the interior portion has become overheated, for safety purposes, the projector is automatically shut down, and the indicator lamps may also be turned off. In such a case, disconnect the power cord, and wait at least 45 minutes. After the projector has sufficiently cooled down, please make confirmation of the attachment state of the lamp and lamp cover, and then turn the power on again.

Shutting the projector down

Only when the projector can not be turned off by usual

 

procedure ( 15), please push the shutdown switch

 

using a pin or similar, and disconnect the power plug

Shutdown switch

from the power outlet. Before turning it on again, wait

 

at least 10 minutes to make the projector cool down

 

enough.

 

Resetting all settings

When it is hard to correct some wrong settings, the FACTORY RESET function of SERVICE item in OPTION menu ( 44) can reset all settings(except LANGUAGE, FILTER TIME, LAMP TIME, FILTER MESSAGE and etc.) to the factory default.

ViewSonic

57

PJ758/PJ759/PJ760

Page 61 Page 63
Image 62
Page 61 Page 63
Contents ViewSonic CE Conformity for European Countries FCC StatementFor Canada Following information is only for EU-member statesImportant Safety Instructions Declaration of RoHS Compliance Copyright Information Serial Number Purchase DateTrademark acknowledgment About this manualThank you for purchasing this projector Content Contents of package Fastening the lens coverHOT Part namesProjector Component Control panelRear panel Remote control Battery coverPJ758/PJ760 Setting upArrangement On a horizontal surface Suspended from the ceilingArrangement PJ759Setting up Speakers Connecting your devicesMonitor VCR/DVD playerConnecting your devices About Plug-and-Play capabilityConnecting power supply Using the security bar and slotPutting batteries Remote controlAbout the remote control signal Mouse right button Press Reset button Changing the frequency of remote control signalUsing as a simple PC mouse & keyboard Mouse left button Press Enter buttonTurning off the power Power on/offTurning on the power Operating Adjusting the volumeSelecting an input signal Temporarily muting the sound€ For a computer signal Searching an input signalSelecting an input signal € For no signal 43 fixedAdjusting the projectors elevator Adjusting the zoom and focusAuto Using the automatic adjustment featureAdjusting the position PositionKeystone Using the magnify featureCorrecting the keystone distortions Magnify ON/OFFFreeze Freezing the screenTemporarily blanking the screen BlankUsing the menu function Using the menu function Advanced MenuAuto Picture ModeAspect KeystoneEasy Menu Color Temp Picture MenuGamma SAVE-4 ÙSAVE-3 Ù SAVE-2 Ù SAVE-1 Picture MenuLOAD-1 Ù LOAD-2 Ù LOAD-3 Ù LOAD-4 LOAD-1, LOAD-2, LOAD-3, LOAD-4For adjusting Color Temp To adjust Custom function in Gamma and Color TempFor adjusting Gamma Gamma Color TempImage Menu For a computer signalFor no signal Over ScanImage Menu PhaseAuto Adjust SizeVideo NR Input MenuProgressive Color SpaceFrame Lock Input MenuVideo Format ComputerCustom ResolutionStandard Standard CustomSetup Menu Speaker Setup MenuVolume AudioScreen Menu BlankScreen Menu Start UPMyScreen registration is finished Capturing error has occurred. Please try againMyScreen Message No Input is DetectedSync is OUT of Range Source NameComputer IN1 Ö Computer IN2 Option MenuAuto Search Video Õ S-VIDEO Õ ComponentAuto OFF Reset Õ CancelOption Menu Lamp TimeFAN Speed ServiceMY Button Filter Message Fine Ù Fast Ù DisableGhost Remote Freq Factory ResetKEY Lock 1NORMAL Ù 2HIGHChanging the Password Using Security FeaturesInputting the Password SecurityTurning on the MyScreen Password Function Using the MyScreen Password FunctionIf you have forgotten your Password Setting the PasswordRegistering the PIN Code Using the PIN Lock FunctionTurning the Password off Turning Off the PIN Lock Function If you have forgotten your PIN CodeTurning On the Transition Detector Function Using the Transition Detector FunctionSetting the Transition Detector Password Setting the Transition Detector off Type number RLC-031 Replacing the lamp MaintenanceLamp Lamp warning LampCleaning the air filter Air filterInside of the projector Caring for the cabinet and remote controlOther care Caring for the lensInternal temperature is rising TroubleshootingThere is no input signal Related messagesRegarding the indicator lamps Resetting all settings Shutting the projector downSignal source does not correctly work Electrical power cord is not pluggedSignal cables are not correctly connected Input changeover settings are mismatchedNot properly adjusted Color settings are not correctly adjustedColor Space setting is not suitable Play monitorSpecification SpecificationsSpecification Specifications Customer Support Who the warranty protects What the warranty coversHow long the warranty is effective What the warranty does not coverEffect of state law Limitation of implied warrantiesExclusion of damages Sales outside the U.S.A. and Canada
Top Page Image Contents