| Basic Input Output System (BIOS) | STL2 Server Board TPS |
| |
|
|
|
|
|
| Code | Error Message | Failure Description |
|
|
|
|
|
|
| 0B93: | BMC SDR Repository empty. | BMC device (chip) failed |
|
|
|
|
|
|
| 0B94: | IPMB signal lines do not respond. | SMC(Satellite Management Controller) failed |
|
|
|
| (Available for use except for the access |
|
|
|
| function to SMC via IPMB) |
|
|
|
|
|
|
| 0B95 | BMC FRU device failure. | SROM storing chassis information failed |
|
|
|
| (Available for use except for FRU command |
|
|
|
| and EMP function.) |
|
|
|
|
|
|
| 0B96 | BMC SDR Repository failure. | BMC device (chip) failed |
|
|
|
|
|
|
| 0B97 | BMC SEL device failure. |
|
|
|
|
|
|
|
| 0BB0: | SMBIOS – SROM data read error | SROM data read error |
|
|
|
|
|
|
| 0BB1: | SMBIOS – SROM data checksum bad | Bad checksum of SROM data |
|
|
|
|
|
|
| 0BD0: | 1st SMBus device address not acknowledged. | Some SMBus device (chip) failed |
|
|
|
|
|
|
| 0BD1: | 1st SMBus device Error detected. |
|
|
|
|
|
|
|
| 0BD2: | 1st SMBus timeout. |
|
|
|
|
|
|
|
|
| Expansion ROM not initialized. | PCI Expansion ROM card not initialized |
|
|
|
|
|
|
|
| Invalid System Configuration Data | System configuration data destroyed |
|
|
|
|
|
|
|
| System Configuration Data Read Error | System configuration data read error |
|
|
|
|
|
|
|
| Resource Conflict | PCI card resource is not mapped correctly. |
|
|
|
|
|
|
|
| System Configuration Data Write error | System configuration data write error |
|
|
|
|
|
|
|
| Warning: IRQ not configured | PCI interrupt is not configured correctly. |
|
|
|
|
|
|
| 8503: | Incorrect memory speed in location: XX, XX, … |
| |
|
|
| XX, XX, … |
|
|
|
|
|
|
A beep code is a series of individual beeps on the PC speaker, each of equal length. The following table describes the error conditions associated with each beep code and the corresponding POST check point code as seen by a port 80h card. For example, if an error occurs at checkpoint 22h, a beep code of
Beeps | Error | Cause | Recommended Action |
|
|
|
|
ROM Checksum Error | — | Change system board | |
|
|
|
|
DRAM Refresh Test Error | — | Change memory DIMM's | |
|
|
|
|
Keyboard Controller Test Error | — | Change system board | |
|
|
|
|
Memory Not Detected | No memory. | Verify DIMM installation. | |
|
| Can not write to memory | Change memory DIMM's |
|
|
|
|
| Memory Capacity Check Error | No memory. | Verify DIMM installation. |
|
| Can not write to memory | Change memory DIMM's |
|
|
|
|
DRAM Address Test Error | Memory address signal failure | Change DIMM or M/B | |
|
|
|
|
DRAM Test low byte Error | Memory data signal failure (low) | Change DIMM or M/B | |
|
|
|
|
DRAM Test high byte Error | Memory data signal failure (high) | Change DIMM or M/B | |
|
|
|
|
All Memory Group Errors | — | — | |
|
|
|
|
BIOS ROM | Error with Shadow RAM | Change system board | |
|
|
|
|
Unexpected Interrupt Test Error | Unexpected interrupt | Change CPU or system board | |
|
|
|
|
All Memory Group Errors | Memory address signal failure | Change DIMM or M/B | |
|
|
|
|