Intel Intel P35/P31 Socket LGA775 Processor Mainboard IDE HDD Auto-Detection, Capacity, Cylinder

Page 25

P3 Series

User's Manual

 

 

 IDE HDD Auto-Detection

This item allows you to detect the parameters of IDE drives by pressing <Enter> key. The parameters will be shown on the screen automatically.

 IDE Channel 0 Master/Slave,SATA Channel 1~4

When set to [Auto], the BIOS will automatically check what kind of IDE or SATA hard drive you are using. If you want to define your own drive yourself, set it to [Manual] and make sure you fully understand the meaning of the parameters. Please refer to the instruction manual provided by the device’s manufacturer to get the setting right.

 Access Mode

This item selects the mode to access your IDE or SATA devices. Leave this item at its default [Auto] setting to detect the access mode of your HDD automatically.

Capacity

 This item displays the approximate capacity of the disk drive. Usually the size is slightly greater than the size of a formatted disk given by a disk-checking program.

 Cylinder

 This item configures the numbers of cylinders.

 Head

 This item configures the numbers of read/write heads.

 Precomp

 This item displays the number of cylinders at which to change the write timing.

 Landing Zone

 This item displays the number of cylinders specified as the landing zone for the read/write

 heads.

 Sector

 This item configures the numbers of sectors per track.

 • Back to Standard CMOS Features Setup Menu

・Drive A & Drive B

 This item sets the type of floppy drives (usually only Drive A) installed.

・ Halt On

 This item determines whether the system stops if an error is detected during system boot-up.

 [All Errors]: The system-boot will stop whenever the BIOS detect a non-fatal error.

 [No Errors]: The system-boot will not stop for any error detected.

 [All, But Keyboard]: The system-boot will stop for all errors except a keyboard error.

 [All, But Diskette]: The system-boot will stop for all errors except a diskette error.

 [All, But Disk/Key]: The system-boot will stop for all errors except a diskette or keyboard error.

・Base Memory

 This item displays the amount of base memory installed in the system. The value of the

  base memory is typically 640K for systems with 640K or more memory size installed on  

 the mainboard.

・Extended Memory

 This item displays the amount of extended memory detected during system boot-up.

・ Total Memory

 This item displays the total memory available in the system.

- 24 -

Page 24 Page 26
Image 25
Page 24 Page 26
Contents P3 Series Copyright DisclaimerTable of Contents Introduction Package ChecklistCPU Specifications -1 For IP35-PROSpecifications -2 For IP35-S Specifications -3 For IP31-CF This picture is only for reference Mainboard Layout -1 PCB Layout for IP35-PROMainboard Layout-2 PCB Layout for IP35-S Mainboard Layout-3 PCB Layout for IP31-CF Connecting Rear Panel I/O Devices AUDIO1 Choosing a Computer Chassis Installing MainboardInstallation of the CPU Installation of the CPU and CPU CoolerInstallation of the CPU Cooler Installation of Memory ModulesFloppy and IDE Disk Drive Connectors Connecting Peripheral DevicesSerial ATA Connectors PCI and PCI Express slotsKeyboard Power FunctionJKB Checking Jumper SettingsCmos Memory Clearing Header Front Panel Switches & Indicators Headers FAN Power ConnectorsFront Panel Audio Connection Header Additional USB Port HeadersATX Power Input Connectors Internal Audio ConnectorsTo Run Bios Setup About Bios SetupPost Power On Self Test About CmosBios Setup Cmos Setup Utility Load Optimized Defaults Load Fail-Safe DefaultsSet Supervisor Password Set User Password・ Time hhmmss ・ Date mmddyyIDE HDD Auto-Detection IDE Channel 0 Master/Slave,SATA Channel 1~4 Access ModeCapacity Cylinder・ Hard Disk Boot Priority ・ Apic Mode PCI-E Compliancy Mode ・ System Bios Cacheable・ Memory Hole At 15M-16M PCI Express Root Port FuncIDE DMA transfer access IDE HDD Block ModeOnChip IDE Device IDE Primary Master/Slave PIOIDE Primary Master/Slave Udma Auto Back to Integrated Peripherals Setup Menu Onboard DeviceOn-Chip Secondary PCI IDE IDE Secondary Master/Slave PIOOnboard FDC Controller Back to Integrated Peripherals Setup Menu Super IO DeviceOnboard Serial Port EPP Mode Select Parallel Port ModeECP Mode Use DMA ・ Hot Key Power on・ Acpi Function ・ Power Management・ Acpi Suspend Type ・ HDD Power Down ・ Suspend Mode・ Power On by Ring ・ Resume by Alarm・ Init Display First ・ Reset configuration data・ Resource controlled by ・ IRQ Resources・ Shutdown Temperature ・ FAN Mode Setting・ Sensor Show On Post ・ CPU Clock Mode ・ CPU Feature・ Ajust Cpu Voltage ・ Ajust Dram VoltageEnter Password Set Supervisor/User PasswordPassword DISABLED！ Driver Installation Exit Hex Name Description Post CodesInitialize INT 00h-1Fh according to Inttbl Test base memory from 256K to 640K and extended memory E1-EF
Top Page Image Contents