Intel 88ENEP3S00 user manual Connecting Peripheral Devices, Floppy and IDE Disk Drive Connectors

Page 16

P3 Series	User's Manual

2.5Connecting Peripheral Devices

2.5.1Floppy and IDE Disk Drive Connectors

BAK_BIOS USR_BIOS

Each of the IDE port connects up to two IDE drives at Ultra ATA/100 mode by one 40-pin, 80-conductor,and 3-connector Ultra ATA/66 ribbon cables.

Connect the single end (blue connector) at the longer length of ribbon cable to the IDE port of this board, the other two ends (gray and black connector) at the shorter length of the ribbon cable to the connectors of your hard drives.

Make sure to configure the “Master” and “Slave” relation before connecting two drives by one single ribbon cable. The red line on the ribbon cable must be aligned with pin-1 on both the IDE port and the hard-drive connector.

The FDD connector connects up to two floppy drives with a 34-wire, 2-connector floppy cable.Connect the single end at the longer length of ribbon cable to the FDD on the board, the two connectors on the other end to the floppy disk drives connector. Generally you need only one floppy disk drive in your system.

The red line on the ribbon cable must be aligned with pin-1 on both the FDD port and the floppy connector.

2.5.2 Serial ATA Connectors

Each SATA connector serves as one single channel to connect one SATA device by SATA cable.

BAK_BIOS USR_BIOS

2.5.3 PCI and PCI Express slots

Install PCI Express X16 graphics card into slot “PCIE1”.

Install PCI Express X1 graphics card into slot "PCIE2" or "PCIE4".

Install PCI Express X4 graphics card into slot "PCIE3".

Install PCI card into slots “PCI1” or “PCI2”.

- 15 -

Image 16

Contents P3 Series Disclaimer CopyrightTable of Contents Package Checklist IntroductionSpecifications -1 For IP35-PRO CPUSpecifications -2 For IP35-S Specifications -3 For IP31-CF Mainboard Layout -1 PCB Layout for IP35-PRO This picture is only for referenceMainboard Layout-2 PCB Layout for IP35-S Mainboard Layout-3 PCB Layout for IP31-CF Connecting Rear Panel I/O Devices AUDIO1 Installing Mainboard Choosing a Computer ChassisInstallation of the CPU and CPU Cooler Installation of the CPUInstallation of Memory Modules Installation of the CPU CoolerConnecting Peripheral Devices Floppy and IDE Disk Drive ConnectorsSerial ATA Connectors PCI and PCI Express slotsKeyboard Power FunctionJKB Checking Jumper SettingsCmos Memory Clearing Header FAN Power Connectors Front Panel Switches & Indicators HeadersAdditional USB Port Headers Front Panel Audio Connection HeaderInternal Audio Connectors ATX Power Input ConnectorsAbout Bios Setup To Run Bios SetupPost Power On Self Test About CmosBios Setup Cmos Setup Utility Load Fail-Safe Defaults Load Optimized DefaultsSet Supervisor Password Set User Password・ Date mmddyy ・ Time hhmmssIDE Channel 0 Master/Slave,SATA Channel 1~4 Access Mode IDE HDD Auto-DetectionCapacity Cylinder・ Hard Disk Boot Priority ・ Apic Mode ・ System Bios Cacheable PCI-E Compliancy Mode・ Memory Hole At 15M-16M PCI Express Root Port FuncIDE HDD Block Mode IDE DMA transfer accessOnChip IDE Device IDE Primary Master/Slave PIOBack to Integrated Peripherals Setup Menu Onboard Device IDE Primary Master/Slave Udma AutoOn-Chip Secondary PCI IDE IDE Secondary Master/Slave PIOOnboard FDC Controller Back to Integrated Peripherals Setup Menu Super IO DeviceOnboard Serial Port Parallel Port Mode EPP Mode SelectECP Mode Use DMA ・ Hot Key Power on・ Acpi Function ・ Power Management・ Acpi Suspend Type ・ Suspend Mode ・ HDD Power Down・ Power On by Ring ・ Resume by Alarm・ Reset configuration data ・ Init Display First・ Resource controlled by ・ IRQ Resources・ Shutdown Temperature ・ FAN Mode Setting・ Sensor Show On Post ・ CPU Feature ・ CPU Clock Mode・ Ajust Cpu Voltage ・ Ajust Dram VoltageSet Supervisor/User Password Enter PasswordPassword DISABLED！ Driver Installation Exit Post Codes Hex Name DescriptionInitialize INT 00h-1Fh according to Inttbl Test base memory from 256K to 640K and extended memory E1-EF