Intel 88ENEP3S00 user manual ・ FAN Mode Setting, ・ Shutdown Temperature, ・ Sensor Show On Post

Page 36

P3 Series	User's Manual

4.5.9 PC Health Status

Phoenix - AwardBIOS CMOS Setup Utility

	PC Health Status
* FAN Control Setting *			Item Help
FAN Mode Setting	[Full	On mode ]
x Slop PWM 1	0.500 PWM		Menu Level	►
x Temperature Limit of OFF	0		Menu Level	►
x Temperature Limit of OFF	0
x Temperature Limit of Start	20
x Temperature Limit of Full	80
x Fan Start PWM	70
x Fan PWM Control	100
* System Health *
Sensor Show On Post	[Enabled]
Shutdown Temperature	[Enabled]
CPU VCORE:	1.32	V
+5 V:	4.97	V
+3.3 V :	3.34	V
VDIMM:	1.82	V
5VSB :	4.99	V
VBAT :	3.26	V
	。
CPU Temp:	31。C
SYS Temp:	23	C
CPU FAN:	1000	RPM
SYS FAN1:	800	RPM
SYS FAN2:	0	RPM

→←	:Move Enter:Select	+/-/PU/PD:Value F10:Save	ESC:Exit F1:General Help
↑↓
	F5: Previous Values	F6: Fail-Safe Defaults	F7: Optimized Defaults

・FAN Mode Setting

This item allows you to set the CPU fan states. When set to [Full on mode], the following items become selectable.

・All Voltages, Fans Speed and Thermal Monitoring

These unchangeable items list the current status of the CPU and environment temperatures, fan speeds, and system power voltage.

・Shutdown Temperature

You can set the processor shutdown temperature here. If the processor temperature exceeds the settings value, system will force to shutdown to protect the processor not overheat.

・Sensor Show On Post

Show the system status when post.

- 35 -

Image 36

Contents P3 Series Disclaimer CopyrightTable of Contents Package Checklist IntroductionSpecifications -1 For IP35-PRO CPUSpecifications -2 For IP35-S Specifications -3 For IP31-CF Mainboard Layout -1 PCB Layout for IP35-PRO This picture is only for referenceMainboard Layout-2 PCB Layout for IP35-S Mainboard Layout-3 PCB Layout for IP31-CF Connecting Rear Panel I/O Devices AUDIO1 Installing Mainboard Choosing a Computer ChassisInstallation of the CPU and CPU Cooler Installation of the CPUInstallation of Memory Modules Installation of the CPU CoolerConnecting Peripheral Devices Floppy and IDE Disk Drive ConnectorsSerial ATA Connectors PCI and PCI Express slotsChecking Jumper Settings Keyboard Power FunctionJKBCmos Memory Clearing Header FAN Power Connectors Front Panel Switches & Indicators HeadersAdditional USB Port Headers Front Panel Audio Connection HeaderInternal Audio Connectors ATX Power Input ConnectorsAbout Bios Setup To Run Bios SetupPost Power On Self Test About CmosBios Setup Cmos Setup Utility Load Fail-Safe Defaults Load Optimized DefaultsSet Supervisor Password Set User Password・ Date mmddyy ・ Time hhmmssIDE Channel 0 Master/Slave,SATA Channel 1~4 Access Mode IDE HDD Auto-DetectionCapacity Cylinder・ Hard Disk Boot Priority ・ Apic Mode ・ System Bios Cacheable PCI-E Compliancy Mode・ Memory Hole At 15M-16M PCI Express Root Port FuncIDE HDD Block Mode IDE DMA transfer accessOnChip IDE Device IDE Primary Master/Slave PIOBack to Integrated Peripherals Setup Menu Onboard Device IDE Primary Master/Slave Udma AutoOn-Chip Secondary PCI IDE IDE Secondary Master/Slave PIOBack to Integrated Peripherals Setup Menu Super IO Device Onboard FDC ControllerOnboard Serial Port Parallel Port Mode EPP Mode SelectECP Mode Use DMA ・ Hot Key Power on・ Power Management ・ Acpi Function・ Acpi Suspend Type ・ Suspend Mode ・ HDD Power Down・ Power On by Ring ・ Resume by Alarm・ Reset configuration data ・ Init Display First・ Resource controlled by ・ IRQ Resources・ FAN Mode Setting ・ Shutdown Temperature・ Sensor Show On Post ・ CPU Feature ・ CPU Clock Mode・ Ajust Cpu Voltage ・ Ajust Dram VoltageSet Supervisor/User Password Enter PasswordPassword DISABLED！ Driver Installation Exit Post Codes Hex Name DescriptionInitialize INT 00h-1Fh according to Inttbl Test base memory from 256K to 640K and extended memory E1-EF