Intel Intel P35/P31 Socket LGA775 Processor Mainboard, 88ENEP3S00 user manual ・ Apic Mode

Page 27

P3 Series

User's Manual

・First Boot Device/Second Boot Device/Third Boot Device/Boot Other Device

Select the drive to boot first, second and third in the [First Boot Device], [Second Boot

Device], and [Third Boot Device] items respectively. The BIOS will boot the operating system according to the sequence of the drive selected. Set [Boot Other Device] to [Enabled] if you wish to boot from another device other than these three items.

・Boot Up Floppy Seek

During POST, BIOS will determine if the floppy disk drive installed if choose [Enable].

・Boot Up NumLock Status

This item defines if the keyboard Num Lock key is active when your system is started.

・Gate A20 Option

[Normal]:

The A20 signal is controlled by keyboard controller or chipset hardware.

[Fast]: (default)

The A20 signal is controlled by port 92 or chipset specific method.

・Typematic Rate Setting

Keystrokes repeat at a rate determined by the keyboard controller. When enabled, the typematic rate and typematic delay can be selected.

・Typematic Rate (Chars/Sec)

Set the number of times a second to repeat a keystroke when you hold the key down. The settings are: 6, 8, 10, 12, 15, 20, 24, and 30.

・Typematic Delay (Msec)

Set the delay time after the key is held down before is begins to repeat the keystroke. The settings are 250, 500, 750, and 1000.

・Security Option

This item determines when the system will prompt for password - every time the system boots or only when enters the BIOS setup.

[Setup]: The password is required only when accessing the BIOS Setup.

[System]: The password is required each time the computer boots up.

Note:  Don’t forget your password. If you forget the password, you will have to open the computer case and clear all information in the CMOS before you can start up the system. But by doing this, you will have to reset all previously set options.

・APIC MODE

This field is used to enable or disable the APIC (Advanced Programmable Interrupt

Controller). Due to compliance with PC2004 design guide, the system is able to run in APIC mode. Enabling APIC mode will expand available IRQ resources for the system.

・MPS Version Control For OS

This item specifies which version of MPS (Multi-Processor Specification) this mainboard will use. Leave this item at its default setting.

・Singal CPU Work Mode

Change the Dual-Core CPU to the single core mode. This item will be enabled while using Dual-Core CPU.

・Report No FDD For WIN 95

When set to [Yes], this item allows you to run some older operating system without floppy disk drive. Leave this item to its default setting.

・Full Screen LOGO Show

This item determines to show the full screen logo when booting.

・Small Logo Show

The Logo is the sign at the top of the screen when POST. If you don't want to show this logo, please set "Disabled".

- 26 -

Page 26 Page 28
Image 27
Page 26 Page 28
Contents P3 Series Copyright DisclaimerTable of Contents Introduction Package ChecklistCPU Specifications -1 For IP35-PROSpecifications -2 For IP35-S Specifications -3 For IP31-CF This picture is only for reference Mainboard Layout -1 PCB Layout for IP35-PROMainboard Layout-2 PCB Layout for IP35-S Mainboard Layout-3 PCB Layout for IP31-CF Connecting Rear Panel I/O Devices AUDIO1 Choosing a Computer Chassis Installing MainboardInstallation of the CPU Installation of the CPU and CPU CoolerInstallation of the CPU Cooler Installation of Memory ModulesPCI and PCI Express slots Connecting Peripheral DevicesFloppy and IDE Disk Drive Connectors Serial ATA ConnectorsChecking Jumper Settings Keyboard Power FunctionJKBCmos Memory Clearing Header Front Panel Switches & Indicators Headers FAN Power ConnectorsFront Panel Audio Connection Header Additional USB Port HeadersATX Power Input Connectors Internal Audio ConnectorsAbout Cmos About Bios SetupTo Run Bios Setup Post Power On Self TestBios Setup Cmos Setup Utility Set User Password Load Fail-Safe DefaultsLoad Optimized Defaults Set Supervisor Password・ Time hhmmss ・ Date mmddyyCylinder IDE Channel 0 Master/Slave,SATA Channel 1~4 Access ModeIDE HDD Auto-Detection Capacity・ Hard Disk Boot Priority ・ Apic Mode PCI Express Root Port Func ・ System Bios CacheablePCI-E Compliancy Mode ・ Memory Hole At 15M-16MIDE Primary Master/Slave PIO IDE HDD Block ModeIDE DMA transfer access OnChip IDE DeviceIDE Secondary Master/Slave PIO Back to Integrated Peripherals Setup Menu Onboard DeviceIDE Primary Master/Slave Udma Auto On-Chip Secondary PCI IDEBack to Integrated Peripherals Setup Menu Super IO Device Onboard FDC ControllerOnboard Serial Port ・ Hot Key Power on Parallel Port ModeEPP Mode Select ECP Mode Use DMA・ Power Management ・ Acpi Function・ Acpi Suspend Type ・ Resume by Alarm ・ Suspend Mode・ HDD Power Down ・ Power On by Ring・ IRQ Resources ・ Reset configuration data・ Init Display First ・ Resource controlled by・ FAN Mode Setting ・ Shutdown Temperature・ Sensor Show On Post ・ Ajust Dram Voltage ・ CPU Feature・ CPU Clock Mode ・ Ajust Cpu VoltageEnter Password Set Supervisor/User PasswordPassword DISABLED！ Driver Installation Exit Hex Name Description Post CodesInitialize INT 00h-1Fh according to Inttbl Test base memory from 256K to 640K and extended memory E1-EF
Top Page Image Contents