Intel Intel P35/P31 Socket LGA775 Processor Mainboard ・ Init Display First, ・ IRQ Resources

Page 35

P3 Series

 

 

 

 

 

User's Manual

 

 

 

 

4.5.8 PnP PCI Configuration

 

 

 

 

 

 

Phoenix - AwardBIOS CMOS Setup Utility

 

 

 

 

PnP/PCI Configurations

 

Init Display First

 

[PCI Slot]

Item Help

Reset Configuration Data

[Disabled]

 

Resources

Controlled By

 

[Auto(ESCD)]

Menu Level

x IRQ

Resources

 

Press Enter

 

 

PCI/VGA

Palette Snoop

 

[Disabled]

 

INT

Pin

1

Assignment

 

[Auto]

 

INT

Pin

2

Assignment

 

[Auto]

 

INT

Pin

3

Assignment

 

[Auto]

 

INT

Pin

4

Assignment

 

[Auto]

 

INT

Pin

5

Assignment

 

[Auto]

 

INT

Pin

6

Assignment

 

[Auto]

 

INT

Pin

7

Assignment

 

[Auto]

 

INT

Pin

8

Assignment

 

[Auto]

 

** PCI Express relative items **

 

Maximum

Payload Size

 

[128]

 

→←

 

 

 

 

 

ESC:Exit F1:General Help

↑↓ :Move Enter:Select +/-/PU/PD:Value F10:Save

F5: Previous Values

F6: Fail-Safe Defaults

F7: Optimized Defaults

Init Display First

This setting specifies which graphics card is your primary graphics adapter. We suggest you to keep the default setting.

Reset configuration data

Usually you'd better keep this setting [Disabled].

Resource controlled by

The plug and play bios from Award can configure all the booting devices and plug and play devices automatically.

IRQ Resources

Press <Enter> to enter the sub-menu and the following screen appears. When "Resources

Controlled By" sets to [Manual], this field is adjustable.

IRQ-3 assigned to PCI Device IRQ-4 assigned to PCI Device IRQ-5 assigned to PCI Device IRQ-7 assigned to PCI Device IRQ-9 assigned to PCI Device IRQ-10 assigned to PCI Device IRQ-11 assigned to PCI Device IRQ-12 assigned to PCI Device IRQ-14 assigned to PCI Device IRQ-15 assigned to PCI Device

PCI/VGA Palette Snoop

If this option sets to [Enabled], different VGA devices which work in different bus will manage the data from CPU with different palettes.

NOTE: This option can fix some issue that the VGA card is not standard .We suggest you to keep the default setting.

Maximum Payload Size

This setting specifies the maximum TLP payload size for the PCI Express devices. The unit is byte.

- 34 -

Image 35
Contents P3 Series Copyright DisclaimerTable of Contents Introduction Package ChecklistCPU Specifications -1 For IP35-PROSpecifications -2 For IP35-S Specifications -3 For IP31-CF This picture is only for reference Mainboard Layout -1 PCB Layout for IP35-PROMainboard Layout-2 PCB Layout for IP35-S Mainboard Layout-3 PCB Layout for IP31-CF Connecting Rear Panel I/O Devices AUDIO1 Choosing a Computer Chassis Installing MainboardInstallation of the CPU Installation of the CPU and CPU CoolerInstallation of the CPU Cooler Installation of Memory ModulesPCI and PCI Express slots Connecting Peripheral DevicesFloppy and IDE Disk Drive Connectors Serial ATA ConnectorsCmos Memory Clearing Header Checking Jumper SettingsKeyboard Power FunctionJKB Front Panel Switches & Indicators Headers FAN Power ConnectorsFront Panel Audio Connection Header Additional USB Port HeadersATX Power Input Connectors Internal Audio ConnectorsAbout Cmos About Bios SetupTo Run Bios Setup Post Power On Self TestBios Setup Cmos Setup Utility Set User Password Load Fail-Safe DefaultsLoad Optimized Defaults Set Supervisor Password・ Time hhmmss ・ Date mmddyyCylinder IDE Channel 0 Master/Slave,SATA Channel 1~4 Access ModeIDE HDD Auto-Detection Capacity・ Hard Disk Boot Priority ・ Apic Mode PCI Express Root Port Func ・ System Bios CacheablePCI-E Compliancy Mode ・ Memory Hole At 15M-16MIDE Primary Master/Slave PIO IDE HDD Block ModeIDE DMA transfer access OnChip IDE DeviceIDE Secondary Master/Slave PIO Back to Integrated Peripherals Setup Menu Onboard DeviceIDE Primary Master/Slave Udma Auto On-Chip Secondary PCI IDEOnboard Serial Port Back to Integrated Peripherals Setup Menu Super IO DeviceOnboard FDC Controller ・ Hot Key Power on Parallel Port ModeEPP Mode Select ECP Mode Use DMA・ Acpi Suspend Type ・ Power Management・ Acpi Function ・ Resume by Alarm ・ Suspend Mode・ HDD Power Down ・ Power On by Ring・ IRQ Resources ・ Reset configuration data・ Init Display First ・ Resource controlled by・ Sensor Show On Post ・ FAN Mode Setting・ Shutdown Temperature ・ Ajust Dram Voltage ・ CPU Feature・ CPU Clock Mode ・ Ajust Cpu VoltageEnter Password Set Supervisor/User PasswordPassword DISABLED! Driver Installation Exit Hex Name Description Post CodesInitialize INT 00h-1Fh according to Inttbl Test base memory from 256K to 640K and extended memory E1-EF