Intel 88ENEP3S00 user manual FAN Power Connectors, Front Panel Switches & Indicators Headers

Page 18

P3 Series	User's Manual

3.4 FAN Power Connectors

These connectors each provide power to the cooling fans installed in your system. CFAN or CFAN1: CPU Fan Power Connector

SYSFAN1: System Fan Power Connector

SYSFAN2: System Fan Power Connector (Optional)

These fan connectors are not jumpers. DO NOT place jumper caps on these connectors.

BAK_BIOS USR_BIOS

3.5 Front Panel Switches & Indicators Headers

Speaker

BAK_BIOS USR_BIOS

HDD_LED (Hard Driver LED Header)

Connect the HDD LED cable to these PINs, in order to see the HDD status

RESET (Reset Control)

This connector connects to the case-mounted reset switch for rebooting your computer without having to turn off your power switch. This is a preferred method of rebooting in order to prolong the lift of the system’s power supply.

PWR-ON (Power Button)

This connector connects to the case-mounted power switch to power ON/OFF the system.

SPEAKER (Speaker)

This 4-pin connector connects to the case-mounted speaker. You should follow the instruction of the speaker cable.

- 17 -

Image 18

Contents P3 Series Disclaimer CopyrightTable of Contents Package Checklist IntroductionSpecifications -1 For IP35-PRO CPUSpecifications -2 For IP35-S Specifications -3 For IP31-CF Mainboard Layout -1 PCB Layout for IP35-PRO This picture is only for referenceMainboard Layout-2 PCB Layout for IP35-S Mainboard Layout-3 PCB Layout for IP31-CF Connecting Rear Panel I/O Devices AUDIO1 Installing Mainboard Choosing a Computer ChassisInstallation of the CPU and CPU Cooler Installation of the CPU Installation of Memory Modules Installation of the CPU CoolerSerial ATA Connectors Connecting Peripheral DevicesFloppy and IDE Disk Drive Connectors PCI and PCI Express slotsChecking Jumper Settings Keyboard Power FunctionJKBCmos Memory Clearing Header FAN Power Connectors Front Panel Switches & Indicators HeadersAdditional USB Port Headers Front Panel Audio Connection HeaderInternal Audio Connectors ATX Power Input ConnectorsPost Power On Self Test About Bios SetupTo Run Bios Setup About CmosBios Setup Cmos Setup Utility Set Supervisor Password Load Fail-Safe DefaultsLoad Optimized Defaults Set User Password・ Date mmddyy ・ Time hhmmssCapacity IDE Channel 0 Master/Slave,SATA Channel 1~4 Access ModeIDE HDD Auto-Detection Cylinder・ Hard Disk Boot Priority ・ Apic Mode ・ Memory Hole At 15M-16M ・ System Bios CacheablePCI-E Compliancy Mode PCI Express Root Port FuncOnChip IDE Device IDE HDD Block ModeIDE DMA transfer access IDE Primary Master/Slave PIOOn-Chip Secondary PCI IDE Back to Integrated Peripherals Setup Menu Onboard DeviceIDE Primary Master/Slave Udma Auto IDE Secondary Master/Slave PIOBack to Integrated Peripherals Setup Menu Super IO Device Onboard FDC ControllerOnboard Serial Port ECP Mode Use DMA Parallel Port ModeEPP Mode Select ・ Hot Key Power on・ Power Management ・ Acpi Function・ Acpi Suspend Type ・ Power On by Ring ・ Suspend Mode・ HDD Power Down ・ Resume by Alarm・ Resource controlled by ・ Reset configuration data・ Init Display First ・ IRQ Resources・ FAN Mode Setting ・ Shutdown Temperature・ Sensor Show On Post ・ Ajust Cpu Voltage ・ CPU Feature・ CPU Clock Mode ・ Ajust Dram VoltageSet Supervisor/User Password Enter PasswordPassword DISABLED！ Driver Installation Exit Post Codes Hex Name DescriptionInitialize INT 00h-1Fh according to Inttbl Test base memory from 256K to 640K and extended memory E1-EF