Intel 88ENEP3S00 user manual Set Supervisor/User Password, Enter Password

Page 38

P3 Series	User's Manual

4.5.11 Load Fail-Safe Defaults

This option opens a dialog box that lets you install fail-safe defaults for all appropriate items in the Setup Utility: Press <Y> and the <Enter> to install the defaults. Press <N> and then <Enter> to not install the defaults. The fail-safe defaults place no great demand on the system and are generally stable. If your system is not functioning correctly, try installing the fail-safe defaults as a first step in getting your system working properly again. If you only want to install fail-safe defaults for a specific option, select and display that option, and then press <F6>.

Load Fail-Safe Defaults (Y/N)? N

4.5.12 Load Optimized Defaults

This option opens a dialog box that let you install optimized defaults for all appropriate items in the Setup Utility. Press <Y> and then <Enter> to install the defaults. Press <N> and then <Enter> to not install the defaults. The optimized defaults place demand on the system that may be greater than the performance level of the components, such as the CPU and the memory. You can cause fatal errors or instability if you install the optimized defaults when your hardware does not support them. If you only want to install setup defaults for a specific option, select and display that option, and then press <F7>.

Load Optimized Defaults (Y/N)? N

4.5.13 Set Supervisor/User Password

When this function is selected, the following message appears at the center of the screen to assist you in creating a password.

Enter Password:

Type the password, up to eight characters, and press <Enter>. The password typed now will clear any previously entered password from CMOS memory. You will be asked to confirm the password. Type the password again and press <Enter>.

Confirm Password:

You may also press <Esc> to abort the selection.

- 37 -

Image 38

Contents P3 Series Disclaimer CopyrightTable of Contents Package Checklist IntroductionSpecifications -1 For IP35-PRO CPUSpecifications -2 For IP35-S Specifications -3 For IP31-CF Mainboard Layout -1 PCB Layout for IP35-PRO This picture is only for referenceMainboard Layout-2 PCB Layout for IP35-S Mainboard Layout-3 PCB Layout for IP31-CF Connecting Rear Panel I/O Devices AUDIO1 Installing Mainboard Choosing a Computer ChassisInstallation of the CPU and CPU Cooler Installation of the CPUInstallation of Memory Modules Installation of the CPU CoolerSerial ATA Connectors Connecting Peripheral DevicesFloppy and IDE Disk Drive Connectors PCI and PCI Express slotsCmos Memory Clearing Header Checking Jumper SettingsKeyboard Power FunctionJKB FAN Power Connectors Front Panel Switches & Indicators HeadersAdditional USB Port Headers Front Panel Audio Connection HeaderInternal Audio Connectors ATX Power Input ConnectorsPost Power On Self Test About Bios SetupTo Run Bios Setup About CmosBios Setup Cmos Setup Utility Set Supervisor Password Load Fail-Safe DefaultsLoad Optimized Defaults Set User Password・ Date mmddyy ・ Time hhmmssCapacity IDE Channel 0 Master/Slave,SATA Channel 1~4 Access ModeIDE HDD Auto-Detection Cylinder・ Hard Disk Boot Priority ・ Apic Mode ・ Memory Hole At 15M-16M ・ System Bios CacheablePCI-E Compliancy Mode PCI Express Root Port FuncOnChip IDE Device IDE HDD Block ModeIDE DMA transfer access IDE Primary Master/Slave PIOOn-Chip Secondary PCI IDE Back to Integrated Peripherals Setup Menu Onboard DeviceIDE Primary Master/Slave Udma Auto IDE Secondary Master/Slave PIOOnboard Serial Port Back to Integrated Peripherals Setup Menu Super IO DeviceOnboard FDC Controller ECP Mode Use DMA Parallel Port ModeEPP Mode Select ・ Hot Key Power on・ Acpi Suspend Type ・ Power Management・ Acpi Function ・ Power On by Ring ・ Suspend Mode・ HDD Power Down ・ Resume by Alarm・ Resource controlled by ・ Reset configuration data・ Init Display First ・ IRQ Resources・ Sensor Show On Post ・ FAN Mode Setting・ Shutdown Temperature ・ Ajust Cpu Voltage ・ CPU Feature・ CPU Clock Mode ・ Ajust Dram VoltageSet Supervisor/User Password Enter PasswordPassword DISABLED！ Driver Installation Exit Post Codes Hex Name DescriptionInitialize INT 00h-1Fh according to Inttbl Test base memory from 256K to 640K and extended memory E1-EF