Intel Intel P35/P31 Socket LGA775 Processor Mainboard, 88ENEP3S00 Installation of Memory Modules

Page 15

P3 Series	User's Manual

2.3.2 Installation of the CPU Cooler

For proper installation, please kindly refer to the instruction manuals of your CPU Cooler.

2.4 Installation of Memory Modules

This mainboard provides four 240-pin DDRII (Double Data Rate) DIMM slots, and supports Dual Channel Memory Technology. For dual channel configuration, you always need to install two identical (the same brand, speed, size and chip-type) memory modules in the DDRII DIMM slots to activate Dual Channel Memory Technology. Otherwise, it will operate at single channel mode.

Static electricity can damage the electronic components of the computer or optional boards. Before starting these procedures, ensure that you are discharged of static electricity by touching a grounded metal object briefly.

To install system memory:

1.Power off the computer and unplug the AC power cord before installing or removing memory modules.

2.Locate the DIMM slot on the board.

3.Hold two edges of the DIMM module carefully, keep away from touching its connectors.

4.Align the notch key on the module with the rib on the slot.

5.Firmly press the module into the slots until the ejector tabs at both sides of the slot automatically snap into the mounting notch. Do not force the DIMM module in with extra force as the DIMM module only fits in one direction.

6.To remove the DIMM modules, push the two ejector tabs on the slot outward simultaneously, and then pull out the DIMM module.

- 14 -

Image 15

Contents P3 Series Copyright DisclaimerTable of Contents Introduction Package ChecklistCPU Specifications -1 For IP35-PROSpecifications -2 For IP35-S Specifications -3 For IP31-CF This picture is only for reference Mainboard Layout -1 PCB Layout for IP35-PROMainboard Layout-2 PCB Layout for IP35-S Mainboard Layout-3 PCB Layout for IP31-CF Connecting Rear Panel I/O Devices AUDIO1 Choosing a Computer Chassis Installing MainboardInstallation of the CPU Installation of the CPU and CPU CoolerInstallation of the CPU Cooler Installation of Memory ModulesPCI and PCI Express slots Connecting Peripheral DevicesFloppy and IDE Disk Drive Connectors Serial ATA ConnectorsChecking Jumper Settings Keyboard Power FunctionJKBCmos Memory Clearing Header Front Panel Switches & Indicators Headers FAN Power ConnectorsFront Panel Audio Connection Header Additional USB Port HeadersATX Power Input Connectors Internal Audio ConnectorsAbout Cmos About Bios SetupTo Run Bios Setup Post Power On Self TestBios Setup Cmos Setup Utility Set User Password Load Fail-Safe DefaultsLoad Optimized Defaults Set Supervisor Password・ Time hhmmss ・ Date mmddyyCylinder IDE Channel 0 Master/Slave,SATA Channel 1~4 Access ModeIDE HDD Auto-Detection Capacity・ Hard Disk Boot Priority ・ Apic Mode PCI Express Root Port Func ・ System Bios CacheablePCI-E Compliancy Mode ・ Memory Hole At 15M-16MIDE Primary Master/Slave PIO IDE HDD Block ModeIDE DMA transfer access OnChip IDE DeviceIDE Secondary Master/Slave PIO Back to Integrated Peripherals Setup Menu Onboard DeviceIDE Primary Master/Slave Udma Auto On-Chip Secondary PCI IDEBack to Integrated Peripherals Setup Menu Super IO Device Onboard FDC ControllerOnboard Serial Port ・ Hot Key Power on Parallel Port ModeEPP Mode Select ECP Mode Use DMA・ Power Management ・ Acpi Function・ Acpi Suspend Type ・ Resume by Alarm ・ Suspend Mode・ HDD Power Down ・ Power On by Ring・ IRQ Resources ・ Reset configuration data・ Init Display First ・ Resource controlled by・ FAN Mode Setting ・ Shutdown Temperature・ Sensor Show On Post ・ Ajust Dram Voltage ・ CPU Feature・ CPU Clock Mode ・ Ajust Cpu VoltageEnter Password Set Supervisor/User PasswordPassword DISABLED！ Driver Installation Exit Hex Name Description Post CodesInitialize INT 00h-1Fh according to Inttbl Test base memory from 256K to 640K and extended memory E1-EF