Intel Intel P35/P31 Socket LGA775 Processor Mainboard, 88ENEP3S00 Choosing a Computer Chassis

Page 13

P3 Series

User's Manual

 

 

Chapter 2 Hardware Setup

2.1 Choosing a Computer Chassis

The mainboard and its component layouts illustrated in this chapter were based mainly on model “IP35-PRO”, unless specifically stated.

Choose a chassis big enough to install this mainboard.

As some features for this mainboard are implemented by cabling connectors on the mainboard to indicators and switches or buttons on the chassis, make sure your chassis supports all the features required.

If there is possibility of adopting some more hard drives, make sure your chassis has sufficient power and space for them.

Most chassis have alternatives for I/O shield located at the rear panel. Make sure the I/O shield of the chassis matches the I/O port configuration of this mainboard. You can find an I/O shield specifically designed for this mainboard in its package.

2.2 Installing Mainboard

Most computer chassis have a base with many mounting holes to allow the mainboard to be securely attached, and at the same time, prevent the system from short circuits. There are two ways to attach the mainboard to the

chassis base: (1) with studs, or (2) with spacers. Basically, the best way to attach the board is with studs. Only if you are unable to do this should you

attach the board with spacers. Line up the holes on

the board with the mounting holes on the chassis. If the holes line up and there are screw holes, you

can attach the board with studs. If the holes line up and there are only slots, you can only attach with spacers. Take the tip of the spacers and insert them

into the slots. After doing this to all the slots, you can slide the board into position aligned with slots. After the board has been positioned, make sure everything is OK before putting the chassis back on.

Always power off the computer and unplug the AC power cord before adding or removing any peripheral or component. Failing to do so may cause severe damage to your mainboard and/or peripherals. Plug in the AC power cord only after you have carefully checked everything.

To install this mainboard:

1.Locate all the screw holes on the mainboard and the chassis base.

2.Place all the studs or spacers needed on the chassis base and have them tightened.

3.Face the mainboard’s I/O ports toward the chassis’s rear panel.

4.Line up all the mainboard’s screw holes with those studs or spacers on the chassis.

5.Install the mainboard with screws and have them tightened.

To prevent shorting the PCB circuit, please REMOVE the metal studs or spacers if they are already fastened on the chassis base and are without mounting-holes on the mainboard to align with.

- 12 -

Image 13
Contents P3 Series Copyright DisclaimerTable of Contents Introduction Package ChecklistCPU Specifications -1 For IP35-PROSpecifications -2 For IP35-S Specifications -3 For IP31-CF This picture is only for reference Mainboard Layout -1 PCB Layout for IP35-PROMainboard Layout-2 PCB Layout for IP35-S Mainboard Layout-3 PCB Layout for IP31-CF Connecting Rear Panel I/O Devices AUDIO1 Choosing a Computer Chassis Installing MainboardInstallation of the CPU Installation of the CPU and CPU CoolerInstallation of the CPU Cooler Installation of Memory ModulesFloppy and IDE Disk Drive Connectors Connecting Peripheral DevicesSerial ATA Connectors PCI and PCI Express slotsKeyboard Power FunctionJKB Checking Jumper SettingsCmos Memory Clearing Header Front Panel Switches & Indicators Headers FAN Power ConnectorsFront Panel Audio Connection Header Additional USB Port HeadersATX Power Input Connectors Internal Audio ConnectorsTo Run Bios Setup About Bios SetupPost Power On Self Test About CmosBios Setup Cmos Setup Utility Load Optimized Defaults Load Fail-Safe DefaultsSet Supervisor Password Set User Password・ Time hhmmss ・ Date mmddyyIDE HDD Auto-Detection IDE Channel 0 Master/Slave,SATA Channel 1~4 Access ModeCapacity Cylinder・ Hard Disk Boot Priority ・ Apic Mode PCI-E Compliancy Mode ・ System Bios Cacheable・ Memory Hole At 15M-16M PCI Express Root Port FuncIDE DMA transfer access IDE HDD Block ModeOnChip IDE Device IDE Primary Master/Slave PIOIDE Primary Master/Slave Udma Auto Back to Integrated Peripherals Setup Menu Onboard DeviceOn-Chip Secondary PCI IDE IDE Secondary Master/Slave PIOOnboard FDC Controller Back to Integrated Peripherals Setup Menu Super IO DeviceOnboard Serial Port EPP Mode Select Parallel Port ModeECP Mode Use DMA ・ Hot Key Power on・ Acpi Function ・ Power Management・ Acpi Suspend Type ・ HDD Power Down ・ Suspend Mode・ Power On by Ring ・ Resume by Alarm・ Init Display First ・ Reset configuration data・ Resource controlled by ・ IRQ Resources・ Shutdown Temperature ・ FAN Mode Setting・ Sensor Show On Post ・ CPU Clock Mode ・ CPU Feature・ Ajust Cpu Voltage ・ Ajust Dram VoltageEnter Password Set Supervisor/User PasswordPassword DISABLED! Driver Installation Exit Hex Name Description Post CodesInitialize INT 00h-1Fh according to Inttbl Test base memory from 256K to 640K and extended memory E1-EF