Intel Intel P35/P31 Socket LGA775 Processor Mainboard, 88ENEP3S00 user manual E1-EF

Page 45

P3 Series		User's Manual

4E	Manufacturing POST	Reboot if Manufacturing POST Loop pin is set. Otherwise
	Loop or Display	display any messages (i.e., any non-fatal errors that were
	Messages	detected during POST) and enter Setup.
4F	Security Check	Ask password security (optional).
50	Write CMOS	Write all CMOS values back to RAM and clear screen.
51	Pre-boot Enable	Enable parity checker.
		Enable NMI, Enable cache before boot.
52	Initialize Option ROMs	Initialize any option ROMs present from C8000h to EFFFFh.
		NOTE: When FSCAN option is enabled, ROMs initialize from
		C8000h to F7FFFh.
53	Initialize Time Value	Initialize time value in 40h: BIOS area.
60	Setup Virus Protect	Setup virus protect according to Setup.
61	Set Boot Speed	Set system speed for boot
62	Setup NumLock	Setup NumLock status according to Setup.
63	Boot Attempt	Set low stack Boot via INT 19h.
B0	Spurious	If interrupt occurs in protected mode.
B1	Unclaimed NMI	If unmasked NMI occurs, display.
		Press F1 to disable NMI, F2 reboot.
E1-EF	Setup Pages	E1- Page 1, E2 - Page 2, etc.
FF	Boot

- 44 -

Image 45

Contents P3 Series Copyright DisclaimerTable of Contents Introduction Package ChecklistCPU Specifications -1 For IP35-PROSpecifications -2 For IP35-S Specifications -3 For IP31-CF This picture is only for reference Mainboard Layout -1 PCB Layout for IP35-PROMainboard Layout-2 PCB Layout for IP35-S Mainboard Layout-3 PCB Layout for IP31-CF Connecting Rear Panel I/O Devices AUDIO1 Choosing a Computer Chassis Installing MainboardInstallation of the CPU Installation of the CPU and CPU CoolerInstallation of the CPU Cooler Installation of Memory ModulesFloppy and IDE Disk Drive Connectors Connecting Peripheral DevicesSerial ATA Connectors PCI and PCI Express slotsChecking Jumper Settings Keyboard Power FunctionJKBCmos Memory Clearing Header Front Panel Switches & Indicators Headers FAN Power ConnectorsFront Panel Audio Connection Header Additional USB Port HeadersATX Power Input Connectors Internal Audio ConnectorsTo Run Bios Setup About Bios SetupPost Power On Self Test About CmosBios Setup Cmos Setup Utility Load Optimized Defaults Load Fail-Safe DefaultsSet Supervisor Password Set User Password・ Time hhmmss ・ Date mmddyyIDE HDD Auto-Detection IDE Channel 0 Master/Slave,SATA Channel 1~4 Access ModeCapacity Cylinder・ Hard Disk Boot Priority ・ Apic Mode PCI-E Compliancy Mode ・ System Bios Cacheable・ Memory Hole At 15M-16M PCI Express Root Port FuncIDE DMA transfer access IDE HDD Block ModeOnChip IDE Device IDE Primary Master/Slave PIOIDE Primary Master/Slave Udma Auto Back to Integrated Peripherals Setup Menu Onboard DeviceOn-Chip Secondary PCI IDE IDE Secondary Master/Slave PIOBack to Integrated Peripherals Setup Menu Super IO Device Onboard FDC ControllerOnboard Serial Port EPP Mode Select Parallel Port ModeECP Mode Use DMA ・ Hot Key Power on・ Power Management ・ Acpi Function・ Acpi Suspend Type ・ HDD Power Down ・ Suspend Mode・ Power On by Ring ・ Resume by Alarm・ Init Display First ・ Reset configuration data・ Resource controlled by ・ IRQ Resources・ FAN Mode Setting ・ Shutdown Temperature・ Sensor Show On Post ・ CPU Clock Mode ・ CPU Feature・ Ajust Cpu Voltage ・ Ajust Dram VoltageEnter Password Set Supervisor/User PasswordPassword DISABLED！ Driver Installation Exit Hex Name Description Post CodesInitialize INT 00h-1Fh according to Inttbl Test base memory from 256K to 640K and extended memory E1-EF