Intel ECB-865 user manual 2.2 1st / 2nd / 3rd Boot Device, Try Other Boot Device, BootUp Num-Lock

Page 65

ECB-865

4.3.2.21st / 2nd / 3rd Boot Device

These options determine the sequence of boot drives (floppy drive A:, hard disk drive C:, or CD-ROM drive) that the AMIBIOS attempts to boot from after AMIBIOS POST completes.

4.3.2.3Try Other Boot Device

Set this option to Yes to try other boot device. The settings are Yes or No. The default setting is Yes.

4.3.2.4S.M.A.R.T. for Hard Disks

Set this option to Enabled the S.M.A.R.T function for Hard Disks. The settings are Enabled or Disabled. The default setting is Disabled.

4.3.2.5BootUp Num-Lock

Set this option to Off to turn the Num Lock key off when the computer is booted so you can use the arrow keys on both the numeric keypad and the keyboard. The settings are On or Off. The default setting is On.

4.3.2.6Floppy Drive Swap

Set this option to Enabled to permit drives A: or B: to be swapped. The settings are Enabled or Disabled. The default setting is Disabled.

4.3.2.7Floppy Drive Seek

Set this option to Enabled to specify that floppy drive A: will perform a seek operation at system boot. The settings are Enabled or Disabled. The default setting is Disabled.

4.3.2.8PS/2 Mouse Support

When this option is set to Enabled, AMIBIOS supports a PS/2-type mouse. The settings are Enabled or Disabled. The default setting is Enabled.

4.3.2.9Primary Display

This option specifies the type of display monitor and adapter in the computer. The settings are Mono, CGA40x25, CGA80x25, VGA/EGA, or Absent. The default setting is VGA/EGA.

4.3.2.10Password Check

This option enables the password checking when the system boots up or runs CMOS Setup. It only takes effect after setting Change Supervisor Password.

Setup: This option will force system to check password before running Setup if you have already entered the current user password in “Change User Password”. By that time, the system will be only able to boot but deny accessing Setup.

Always: Password prompt appears every boot-up. The system will not boot and deny access Setup with invalid password. The best way is to clear CMOS or try to reload BIOS Setup to boot up system.

ECB-865 User’s Manual 55

Image 65

Contents User’s Manual ECB-865 FCC Statement Trademark Acknowledgement Copyright NoticeDisclaimer Life Support PolicyMessage to the Customer Evalue Customer ServicesTechnical Support Evalue Technology Inc Evalue Europe A/SProduct Warranty Packing List Manual Objectives Introduction Watchdog Timer Programming Jumper & ConnectorEntering Setup Setting JumpersConnector Definitions Map Revision Date Comment Document Amendment HistoryManual Objectives System Overview IntroductionChipset ITE IT8712F-A System SpecificationsExpansion Interface Mechanical and Environmental Weight 0.5 KgArchitecture Overview 1 82815 Gmch and 82801BA AGP Interface Dram InterfaceMultiplexed AGP and Display Cache Interface Ethernet 7.1 ICH2 LAN Controller PCI Interface6 USB Systems DiskOnChip IntelITE IT8712F-A Safety Precautions Hardware ConfigurationInstallation Procedure Main Memory Removing CPUSystems’ DiskOnChip Flash Disk Installing DOCExpansion Interface Installing the Single Board Computer 1 815E integrated Graphics Controller Drivers Support Enable WDT Watchdog Timer ProgrammingDisable WDT Re-trigger WDTJumper & Connector Jumper & Connector Layout Jumpers Label Function Jumper & Connector ListJP10 JP11J10 Connectors Label FunctionJ11 J12Setting Jumpers Watchdog Timer Programming I/O Address Select JP6 Watchdog Timer Enable / Disable Onboard Watchdog Timer JP12Clear Cmos JP9 0553H / 0033H 0543H / 0343HSec Watchdog Timer Time-Out Interval Select JP10JP10 16 Sec 32 Sec 64 Sec 10.3 COM2 RS-232/422/485 Select JP1, JP2~JP5Bus Master Systems DiskOnChip Memory Address Select JP11Proprietary PCI Bus Master Selection JP13 External Speaker Connector J2 Connector Definitions System Reset Connector J1Keyboard Lock & Power Indicator Connector J3 Primary IDE / Secondary IDE Active Indicator Connector J4Primary IDE Connector J5 Secondary IDE Connector J10 ECB-865 Primary Master connector STROBE, with the PIIX4 latching RESET# Floppy Connector J6 DRVDEN0/1# Signal Description Floppy Connector J6Parallel Port Connector J11 ATX Power Button Connector J811.12 DB25 Parallel Port Connector J11 STB# Signal Description Parallel Port Connector J11GND DTR CTS CTS RTS DSR GND CTS/RTS + Signal Description USB Connector J13, J19 USB Connector J13, J19CPU Fan and System Fan Connector J14, J25 Fast & Standard IrDA Connector J15Smart Card Interface J17 Signal Configuration Fast & Standard IrDA Connector J15ATX Power Controller J16 Signal Description 10/100Base-Tx Ethernet Connector J18, J20 11.28 10/100 BASE-Tx Ethernet Connector J18, J20Signal Description CRT Connector J22 CRT Connector J2211.33 PS/2 Keyboard Connector J26 Internal Keyboard Connector J24Signal Description Int. & PS/2 Keyboard Connector J24, J26 11.35 PS/2 Mouse Connector J26Proprietary PCI Connector J21 Write bursts System Interface Control Arbitration Error ReportingInterrupts Press F1 to Run Setup or Resume AMI Bios SetupEnter key to accept or enter the sub-menu AMI Bios Setup Main MenuStandard Cmos Setup Menu Cmos Setup Reference TableDate and Time Configuration Floppy A, Floppy BMaster Disk, Slave Disk Boot Sector Virus ProtectionQuick Boot Advanced Cmos Setup DefaultsTry Other Boot Device 2.2 1st / 2nd / 3rd Boot DeviceBootUp Num-Lock Password CheckShadow Memory from Address C000~DFFF, 16K Per Segment Boot To OS/2System Bios Cacheable CPU Ratio Selection Advanced Chipset Setup DefaultsICH Delayed Transaction Internal Graphic Mode Select Sdram RAS# to CAS# DelayMemory Hole Dram Cycle time SCLKsPower Management/ APM Power Management Setup DefaultsGreen PC Monitor Power State Acpi Aware O/SStand by Time Out Minute CPU Critical TemperatureSuspend Time Out Minute Throttle Slow Clock RatioWake Up on LAN Power Button FunctionWake Up on Ring Plug and Play Aware O/S PCI / Plug and Play Setup DefaultsClear Nvram PCI Latency Timer PCI ClocksPCI / VGA Palette Snoop Allocate IRQ to PCI VGAOnBoard FDC Peripheral Setup DefaultsOnBoard Serial Port1 OnBoard Serial Port2Parallel Port Mode DisabledOn Board Parallel Port 378hOn-Chip IDE Parallel Port IRQParallel Port DMA Channel Hardware Monitor Setup Defaults User’s Manual Driver Installation for Ethernet Adapter Windows Driver InstallationUser’s Manual ECB-865 User’s Manual ECB-865 Windows NT 4.0 Ethernet Installation ECB-865 User’s Manual ECB-865 User’s Manual Driver Installation for Display Adapter Windows User’s Manual ECB-865 User’s Manual ECB-865 Windows NT 4.0 Display Installation ECB-865 User’s Manual ECB-865 Measurement Drawing Bios Rev New Features Bugs/Problems Solved Known Problems Appendix a Bios RevisionsMemory Map Appendix B System ResourcesPort Description MapUser’s Manual Interrupt Description Interrupt UsageDMA-channel Description DMA-channel UsageIf it beeps… Then… Appendix C Amibios Power-On Self TestCode Description Appendix D Amibios Post Check Point ListBios User’s Manual Present User’s Manual ECB-865 User’s Manual