Lenovo 9279, 6490, 9635, 9637, 9277 Operating environment, Electrical current safety information

Page 13

vDo not use non-desktop air filtration devices.

Operating environment

The optimal environment in which to use your computer is 10°C-35°C (50°F-95°F) with humidity ranging between 35% and 80%. If your computer is stored or transported in temperatures less than 10°C (50°F), allow the cold computer to rise slowly to an optimal operating temperature of 10°C-35°C (50°F-95°F) before use. This process could take two hours in extreme conditions. Failure to allow your computer to rise to an optimal operating temperature before use could result in irreparable damage to your computer.

If possible, place your computer in a well-ventilated and dry area without direct exposure to sunshine.

Keep electrical appliances such as an electric fan, radio, high-powered speakers, air conditioner, and microwave oven away from your computer because the strong magnetic fields generated by these appliances can damage the monitor and data on the hard disk drive.

Do not place any beverages on top of or beside the computer or other attached devices. If liquid is spilled on or in the computer or an attached device, a short circuit or other damage might occur.

Do not eat or smoke over your keyboard. Particles that fall into your keyboard can cause damage.

Electrical current safety information

Danger

Electrical current from power, telephone, and communication cables is hazardous.

To avoid a shock hazard:

vTo prevent possible shock hazard, do not use your computer during a lightning storm.

vDo not connect or disconnect any cables or perform installation, maintenance, or reconfiguration of this product during an electrical storm.

vConnect all power cords to a properly wired and grounded electrical outlet.

vConnect to properly wired outlets any equipment that will be attached to this product.

vWhen possible, use one hand only to connect or disconnect signal cables.

vNever turn on any equipment when there is evidence of fire, water, or structural damage.

vDisconnect the attached power cords, telecommunications systems, networks, and modems before you open the device covers, unless instructed otherwise in the installation and configuration procedures.

vConnect and disconnect cables as described in the following table when installing, moving, or opening covers on this product or attached devices.

Important safety information

xi

Image 13
Contents User Guide Page User Guide Page Contents Troubleshooting Conditions that require immediate action Important safety informationService and upgrades General safety guidelinesStatic electricity prevention Power cords and power adaptersVoltage-selection switch Plugs and outlets Extension cords and related devicesExternal devices BatteriesHeat and product ventilation Operating environment Electrical current safety informationModem safety information Lithium battery noticeTo connect To disconnect Products with television tuner options installed Power supply statementLaser compliance statement Proper grounding for the cable Example of antenna groundingCleaning and maintenance Data safetyUsing headphones or earphones Additional safety information Introduction Xviii User Guide Comfort Arranging your workspaceAir circulation Glare and lightingElectrical outlets and cable lengths Connecting your computer Setting up your computerUser Guide Setting up your computer User Guide 1394 Finishing the software installation Turning on powerCompleting important tasks Installing other operating systemsUpdating your operating system Updating your antivirus softwareUser Guide Features Installing optionsVideo subsystem Operating systems preinstalled varies by model type Dimensions SpecificationsWeight EnvironmentTools required Available optionsHandling static-sensitive devices Installing external optionsLocating the connectors on the front of your computer Locating the connectors on the rear of your computer Obtaining device drivers Connector DescriptionRemoving the cover Locating components Identifying parts on the system board Installing options User Guide What to do next Installing memoryInstalling adapters What to do next Drive specifications Installing internal drivesInstalling options Installing a drive in bay 1 or bay Installing options Connecting the first optical drive Connecting drivesInstalling security features Connecting a serial ATA hard disk driveIntegrated cable lock Changing the battery Password protectionPadlock Erasing a lost or forgotten password clearing Cmos Replacing the cover and connecting the cables User Guide Creating and using the Product Recovery disc Recovering softwarePerforming backup and recovery operations Using the Rescue and Recovery workspace Creating and using rescue media To create rescue media, do the following Creating and using a Recovery Repair disketteRecovering or installing device drivers Solving recovery problems Setting a rescue device in the startup sequenceUser Guide Starting the Setup Utility program Using the Setup UtilityViewing and changing settings Using passwordsAdministrator Password User PasswordSetting, changing, and deleting a password Using Security Profile by DeviceSelecting a temporary startup device Selecting a startup deviceChanging the startup device sequence Exiting from the Setup Utility program Advanced settingsUpdating flashing Bios from a diskette Using system programsUpdating system programs User Guide Basic troubleshooting Troubleshooting and diagnosticsSymptom Action Diagnostic programs PC-Doctor for DOS PC-Doctor for WindowsRunning diagnostics from the CD or diskettes PC-Doctor for Windows PE Cleaning the mouseOptical mouse Non-optical mouse1 Retainer ring 2 Ball 3 Plastic rollers 4 Ball cage Information resources Getting information, help, and serviceOnline Books folder ThinkVantage Productivity CenterSafety and warranty Access HelpHelp and service Calling for service Using the documentation and diagnostic programsPurchasing additional services Using other servicesBasic AT commands Appendix A. Manual modem commandsSet Pulse dial as default Low speaker volumeSet Tone Dial as default Internal speaker on until carrier detectedExtended AT commands MNP/V.42/V.42bis/V.44 commands Fax Class 2 commands Fax Class 1 commandsVoice commands Appendix A. Manual modem commands User Guide Appendix B. Notices Trademarks Television output noticeIndex Page Page Part Number