Lenovo 9389, 6490, 9635 Lithium battery notice, Modem safety information, To connect To disconnect

Page 14

To connect:		To disconnect:
1.	Turn everything OFF.	1.	Turn everything OFF.
2.	First, attach all cables to devices.	2.	First, remove power cords from outlet.
3.	Attach signal cables to connectors.	3.	Remove signal cables from connectors.
4.	Attach power cords to outlet.	4.	Remove all cables from devices.
5.	Turn device ON.

Lithium battery notice

Caution

Danger of explosion if battery is incorrectly replaced.

When replacing the lithium coin cell battery, use only the same or an equivalent type that is recommended by the manufacturer. The battery contains lithium and can explode if not properly used, handled, or disposed of.

Do not:

vThrow or immerse into water

vHeat to more than 100°C (212°F)

vRepair or disassemble

Dispose of the battery as required by local ordinances or regulations.

The following statement applies to users in the state of California, U.S.A.

Perchlorate material: Special handling may apply. See

www.dtsc.ca.gov/hazardouswaste/perchlorate.

Modem safety information

Caution

To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line cord.

To reduce the risk of fire, electrical shock, or injury when using telephone equipment, always follow basic safety precautions, such as:

vNever install telephone wiring during a lightning storm.

vNever install telephone jacks in wet locations unless the jack is specifically designed for wet locations.

vNever touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface.

vUse caution when installing or modifying telephone lines.

vAvoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning.

vDo not use the telephone to report a gas leak in the vicinity of the leak.

xiiUser Guide

Image 14

Contents User Guide Page User Guide Page Contents Troubleshooting Important safety information Conditions that require immediate actionGeneral safety guidelines Service and upgradesPower cords and power adapters Static electricity preventionVoltage-selection switch External devices Extension cords and related devicesPlugs and outlets BatteriesHeat and product ventilation Electrical current safety information Operating environmentTo connect To disconnect Lithium battery noticeModem safety information Laser compliance statement Power supply statementProducts with television tuner options installed Example of antenna grounding Proper grounding for the cableUsing headphones or earphones Data safetyCleaning and maintenance Additional safety information Introduction Xviii User Guide Arranging your workspace ComfortElectrical outlets and cable lengths Glare and lightingAir circulation Setting up your computer Connecting your computerUser Guide Setting up your computer User Guide 1394 Turning on power Finishing the software installationUpdating your operating system Installing other operating systemsCompleting important tasks Updating your antivirus softwareUser Guide Installing options FeaturesVideo subsystem Operating systems preinstalled varies by model type Weight SpecificationsDimensions EnvironmentAvailable options Tools requiredInstalling external options Handling static-sensitive devicesLocating the connectors on the front of your computer Locating the connectors on the rear of your computer Connector Description Obtaining device driversRemoving the cover Locating components Identifying parts on the system board Installing options User Guide Installing memory What to do nextInstalling adapters What to do next Installing internal drives Drive specificationsInstalling options Installing a drive in bay 1 or bay Installing options Connecting drives Connecting the first optical driveConnecting a serial ATA hard disk drive Installing security featuresIntegrated cable lock Padlock Password protectionChanging the battery Erasing a lost or forgotten password clearing Cmos Replacing the cover and connecting the cables User Guide Recovering software Creating and using the Product Recovery discPerforming backup and recovery operations Using the Rescue and Recovery workspace Creating and using rescue media Creating and using a Recovery Repair diskette To create rescue media, do the followingRecovering or installing device drivers Setting a rescue device in the startup sequence Solving recovery problemsUser Guide Viewing and changing settings Using the Setup UtilityStarting the Setup Utility program Using passwordsSetting, changing, and deleting a password User PasswordAdministrator Password Using Security Profile by DeviceChanging the startup device sequence Selecting a startup deviceSelecting a temporary startup device Advanced settings Exiting from the Setup Utility programUpdating system programs Using system programsUpdating flashing Bios from a diskette User Guide Symptom Action Troubleshooting and diagnosticsBasic troubleshooting Diagnostic programs PC-Doctor for Windows PC-Doctor for DOSRunning diagnostics from the CD or diskettes Optical mouse Cleaning the mousePC-Doctor for Windows PE Non-optical mouse1 Retainer ring 2 Ball 3 Plastic rollers 4 Ball cage Online Books folder Getting information, help, and serviceInformation resources ThinkVantage Productivity CenterHelp and service Access HelpSafety and warranty Using the documentation and diagnostic programs Calling for serviceUsing other services Purchasing additional servicesAppendix A. Manual modem commands Basic AT commandsSet Tone Dial as default Low speaker volumeSet Pulse dial as default Internal speaker on until carrier detectedExtended AT commands MNP/V.42/V.42bis/V.44 commands Fax Class 1 commands Fax Class 2 commandsVoice commands Appendix A. Manual modem commands User Guide Appendix B. Notices Television output notice TrademarksIndex Page Page Part Number