Lenovo 8973, 6490, 9635, 9637, 9277, 9269, 9631, 9283, 9287, 9265, 9383 Installing a drive in bay 1 or bay

Page 50

Installing a drive in bay 1 or bay 2

To install a drive in bay 1 or bay 2, follow these steps:

1.Remove the computer cover. See “Removing the cover” on page 20.

2.Remove the front bezel by releasing the three plastic tabs on the left side and pivoting the bezel outward. Carefully set the bezel to the side without disconnecting the power switch and LED assembly cable.

Note: Notice the spare retainer bracket 1 attached to the side of the upper drive cage.

3.Remove the metal static shield from the drive bay using your fingers to pull it outward.

4.If you are installing a drive with accessible media, such as an optical drive, remove the plastic panel in the bezel for bay 2 by squeezing the plastic tabs that secure the panel on the inside of the bezel.

5.If you are installing any type of drive other than a serial ATA hard drive, make sure the drive that you are installing is set correctly as either a master or a slave device.

Note: A serial ATA hard disk drive does not need to be set as either a master or a slave device.

If you are installing an optical drive or a parallel ATA hard disk drive, set it as a master device. Refer to the documentation that comes with your drive for master/slave jumper information.

6.Remove the retainer bracket from the upper driver cage by sliding it downward.

30User Guide

Image 50
Contents User Guide Page User Guide Page Contents Troubleshooting Important safety information Conditions that require immediate actionGeneral safety guidelines Service and upgradesPower cords and power adapters Static electricity preventionVoltage-selection switch External devices Extension cords and related devicesPlugs and outlets BatteriesHeat and product ventilation Electrical current safety information Operating environmentTo connect To disconnect Lithium battery noticeModem safety information Laser compliance statement Power supply statementProducts with television tuner options installed Example of antenna grounding Proper grounding for the cableUsing headphones or earphones Data safetyCleaning and maintenance Additional safety information Introduction Xviii User Guide Arranging your workspace ComfortElectrical outlets and cable lengths Glare and lightingAir circulation Setting up your computer Connecting your computerUser Guide Setting up your computer User Guide 1394 Turning on power Finishing the software installationUpdating your operating system Installing other operating systemsCompleting important tasks Updating your antivirus softwareUser Guide Installing options FeaturesVideo subsystem Operating systems preinstalled varies by model type Weight SpecificationsDimensions EnvironmentAvailable options Tools requiredInstalling external options Handling static-sensitive devicesLocating the connectors on the front of your computer Locating the connectors on the rear of your computer Connector Description Obtaining device driversRemoving the cover Locating components Identifying parts on the system board Installing options User Guide Installing memory What to do nextInstalling adapters What to do next Installing internal drives Drive specificationsInstalling options Installing a drive in bay 1 or bay Installing options Connecting drives Connecting the first optical driveConnecting a serial ATA hard disk drive Installing security featuresIntegrated cable lock Padlock Password protectionChanging the battery Erasing a lost or forgotten password clearing Cmos Replacing the cover and connecting the cables User Guide Recovering software Creating and using the Product Recovery discPerforming backup and recovery operations Using the Rescue and Recovery workspace Creating and using rescue media Creating and using a Recovery Repair diskette To create rescue media, do the followingRecovering or installing device drivers Setting a rescue device in the startup sequence Solving recovery problemsUser Guide Viewing and changing settings Using the Setup UtilityStarting the Setup Utility program Using passwordsSetting, changing, and deleting a password User PasswordAdministrator Password Using Security Profile by DeviceChanging the startup device sequence Selecting a startup deviceSelecting a temporary startup device Advanced settings Exiting from the Setup Utility programUpdating system programs Using system programsUpdating flashing Bios from a diskette User Guide Symptom Action Troubleshooting and diagnosticsBasic troubleshooting Diagnostic programs PC-Doctor for Windows PC-Doctor for DOSRunning diagnostics from the CD or diskettes Optical mouse Cleaning the mousePC-Doctor for Windows PE Non-optical mouse1 Retainer ring 2 Ball 3 Plastic rollers 4 Ball cage Online Books folder Getting information, help, and serviceInformation resources ThinkVantage Productivity CenterHelp and service Access HelpSafety and warranty Using the documentation and diagnostic programs Calling for serviceUsing other services Purchasing additional servicesAppendix A. Manual modem commands Basic AT commandsSet Tone Dial as default Low speaker volumeSet Pulse dial as default Internal speaker on until carrier detectedExtended AT commands MNP/V.42/V.42bis/V.44 commands Fax Class 1 commands Fax Class 2 commandsVoice commands Appendix A. Manual modem commands User Guide Appendix B. Notices Television output notice TrademarksIndex Page Page Part Number