Sanyo PLC-XD2600 Remote Control Operating Range, Remote Control Code, Two AAA size batteries

Page 12

Part Names and Functions

Remote Control Battery Installation

1

Open the battery

compartment lid.

2

Install new batteries

3

Replace the

into the compartment.

compartment lid.

Two AAA size batteries

For correct polarity

(+ and –), be sure battery terminals are in contact with pins in compartment.

To ensure safe operation, please observe the following precautions :

●Use two (2) AAA or LR03 type alkaline batteries.

●Always replace batteries in sets.

●Do not use a new battery with a used battery.

●Avoid contact with water or liquid.

●Do not expose the remote control to moisture or heat.

●Do not drop the remote control.

●If the battery has leaked on the remote control, carefully wipe the case clean and install new batteries.

●Risk of an explosion if battery is replaced by an incorrect type.

●Dispose of used batteries according to the instructions or your local disposal rule or guidelines.

Remote Control Operating Range

Point the remote control toward the projector (Infrared Remote Receiver) when pressing the buttons. Maximum operating range for the remote control is about 16.4'(5 m) and 60 degrees in front of the projector.

16.4' (5 m)

30°

30° Remote control

Remote Control Code

The 2 different remote control codes (Code 1–Code 2) are assigned to this projector. Switching the remote

control codes prevents interference from other remote controls when several projectors or video equipment

next to each other are operated at the same time. Change the remote control code for the projector first before changing that for the remote control. See "Remote control" in the Setting Menu on page 53.

Press and hold the MENU and IMAGE buttons for more than five seconds to switch between the Code 1 and Code 2. The initial code is set to Code 1.

MENU button

IMAGE button

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Model PLC-XD2200 PLC-XD2600 Network SupportedFeatures and Design Table of Contents Safety Precaution To the OwnerSafety Instructions Safety Instructions Air Circulation Installing the Projector in Proper PositionMoving the Projector AC Power Cord for the United States and Canada AC Power Cord for the United KingdomCompliance Part Names and Functions FrontBack BottomPart Names and Functions Rear Terminal ⑥ LAN Connection Terminal ⑦ Audio IN（VideoPart Names and Functions Top Control Part Names and Functions Remote Control Remote Control Operating Range Remote Control CodeTwo AAA size batteries Installation Adjustable FootPositioning the Projector Installation Connecting to a Computer Cables used for connectionInstallation Connecting to Video Equipment Audio OUT Installation Connecting the AC Power Cord Projector side AC outlet sideFor Continental Europe For the U..K For the U..S..A.. and CanadaInput signal guidance window Basic OperationTurning On the Projector Selected Input Source and Lamp ControlBasic Operation PIN Code Input Dialog BoxBasic Operation Turning Off the Projector Direct OFF FunctionBasic Operation How to Operate the On-Screen Menu Remote ControlTop Control On-Screen Menu④ Image adjust ⑦ SettingBasic Operation Menu Bar ① InputBasic Operation Zoom and Focus Adjustment Auto Setup FunctionKeystone Correction Basic Operation Sound Adjustment VolumeVolume Dialog Box MuteBasic Operation Remote Control Operation Timer button No Show buttonImage button Screen buttonComputer Input Input Source Selection RGB Computer 1/ComputerInput Menu Computer Input Computer System Selection PC System MenuAuto ModeComputer Input Auto PC Adjustment PC adjust MenuTo store adjustment parameters Auto PC adjComputer Input Manual PC Adjustment Reset Mode freeMode free Computer InputComputer Input Image Mode Selection Image select MenuComputer Input Image Adjustment Image Adjust MenuScreen Size Adjustment Screen MenuCustom adj Position H/VDigital zoom + Digital zoomVideo Input Input Source Selection Video, S-videoVideo Input MenuComponent RGB ScartVideo Input Video System Selection Video or S-videoComponent AV System Menu Component Select Video , S-video or Computer 1ComponentVideo Input Image Mode Selection CinemaImage button Dynamic Standard Cinema Blackboard Green Colorboard ImageVideo Input Image Adjustment ColorTint Off Disabled Lower reduction Higher reduction Progressive Video InputStore Menu Noise reductionVideo Input Screen Size Adjustment Setting SettingSetting Menu Language LanguageAuto setup Auto setupInput search Auto KeystonePower off? p.20 KeystoneBackground DisplayLogo Logo and Logo PIN code lock settings DefaultLogo select Logo selectCapture Logo PIN code lockCapture Logo PIN code lockChange the Logo PIN code lock setting Enter a Logo PIN codeChange the Logo PIN code Ceiling RearTerminal ComputerPower management Shut downDirect on Standby mode TimerClosed Caption Lamp control Remote control Remote controlTo change the code for the remote control Lamp controlKey lock PIN code lock Security Key lock and PIN code lockKey lock PIN code lockChange the PIN code lock setting Enter a PIN code Change the PIN codeLamp counter reset Video delay controlFan Fan controlFactory default Factory defaultFilter counter Filter counterInformation Input Source Information DisplayMaintenance and Cleaning Projector is shut down and the Warning indicator lights redThen check the matters below Maintenance and Cleaning Cleaning the Filters Resetting the Filter CounterFilter counter Maintenance and Cleaning Attaching the Lens Cap Cleaning the Projection LensCleaning the Projector Cabinet Maintenance and Cleaning Lamp Replacement Reset the lamp replacement counterLamp replacement icon Lamp Replace indicatorMaintenance and Cleaning Service Parts No 349Troubleshooting AppendixAppendix Remote Control does Indicator blinks or lightsImage is distorted or runs off PIN code dialog box appearsAppendix Appendix Menu Tree System AutoSetting Image select Image Adjust ScreenInformation Appendix Indicators and Projector Condition IndicatorsAppendix Compatible Computer Specifications ON-SCREEN ResolutionAppendix Technical Specifications Optional Parts Appendix PJ Link Notice Appendix Configurations of Terminals Control Port Connector D-sub 9 pinTerminal Analog RGB Mini D-sub 15 pin Appendix PIN Code Number Memo PIN Code Lock NoLogo PIN Code Lock No Dimensions Appendix KR8AC
Related manuals
Manual 2 pages 61.55 Kb

PLC-XD2600 specifications

The Sanyo PLC-XD2600 is a high-performance multimedia projector that has gained popularity among educators, business professionals, and home theater enthusiasts alike. Combining advanced technology with user-friendly features, it delivers impressive visual quality and versatility.

One of the standout features of the PLC-XD2600 is its high brightness rating of 3,000 ANSI lumens, ensuring vibrant and vivid images even in well-lit environments. This makes it suitable for classrooms, conference rooms, and large venues where ambient light can be a challenge. The projector's native XGA resolution (1024 x 768) allows for clear and sharp image reproduction, making text and graphics easily readable.

Sanyo has incorporated an advanced liquid crystal display (LCD) technology in the PLC-XD2600, which contributes to its exceptional color accuracy and brightness. This technology ensures deeper blacks and brighter whites, enhancing the overall viewing experience. Furthermore, the projector supports a contrast ratio of 600:1, adding to the richness of images displayed.

Another significant characteristic of the PLC-XD2600 is its long lamp life. The projector uses a high-efficiency lamp designed to last up to 4,000 hours in normal mode and up to 5,000 hours in eco mode. This durability not only reduces the frequency of lamp replacements but also contributes to lower maintenance costs, making it an economical choice for long-term use.

Portability is a key aspect of the Sanyo PLC-XD2600, weighing only around 6.6 kg. Its compact design allows for easy transport between different locations, making it an ideal solution for traveling professionals. The projector is equipped with a variety of connectivity options, including VGA, composite, and S-Video inputs, offering flexibility to connect with various devices such as laptops, DVD players, and gaming consoles.

The user-friendly interface of the PLC-XD2600 enhances its accessibility, featuring an intuitive remote control and an easy-to-navigate menu system. This simplifies the setup process and allows users to adjust settings with ease.

In conclusion, the Sanyo PLC-XD2600 combines high brightness, excellent image quality, long lamp life, and portability, making it a reliable choice for diverse projection needs. Whether for educational purposes, professional presentations, or home entertainment, this projector stands out as a versatile option that delivers a compelling viewing experience.
Top Page Image Contents