Sanyo PLC-XD2600 owner manual Input Source Information Display

Page 58

Information

Input Source Information Display

The Information Menu is used for checking the status of the image signal being projected and the operation of the projector.

Direct Operation

Press the INFO. button on the remote control to display the Information Menu.

Menu Operation

Press the Point ▲▼ buttons to select the Information. The Information Menu is displayed.

See below for displayed information.

Input

The selected input source is displayed.

H-sync freq..

The horizontal frequency of the input signal is displayed in KHz, or - - - - KHz when no signal.

V-sync freq..

The vertical frequency of the input signal is displayed in Hz, or - - - - Hz when no signal. Numbers of Hz doubles when during Interlace.

Screen

The selected screen size is displayed.

Language

The selected language is displayed.

Lamp status

The selected lamp mode is displayed.

Lamp counter

The cumulative lamp operating time is displayed.

Power management

Off, Ready or Shut down, and Timer are displayed.

Key lock

The selected Key lock icon is displayed.

PIN code lock

Off or On1 or On2 is displayed.

Remote control

The selected remote code is displayed.

Remote Control

INFO.. button

Information Menu

58

Image 58

Contents Model PLC-XD2200 PLC-XD2600 Network SupportedFeatures and Design Table of Contents Safety Precaution To the OwnerSafety Instructions Installing the Projector in Proper Position Safety Instructions Air CirculationMoving the Projector AC Power Cord for the United Kingdom AC Power Cord for the United States and CanadaCompliance Back Part Names and FunctionsFront BottomPart Names and Functions Rear Terminal ⑥ LAN Connection Terminal ⑦ Audio IN（VideoPart Names and Functions Top Control Part Names and Functions Remote Control Remote Control Code Remote Control Operating RangeTwo AAA size batteries Adjustable Foot InstallationPositioning the Projector Installation Connecting to a Computer Cables used for connectionInstallation Connecting to Video Equipment Audio OUT For Continental Europe For the U..K Installation Connecting the AC Power CordProjector side AC outlet side For the U..S..A.. and CanadaTurning On the Projector Input signal guidance windowBasic Operation Selected Input Source and Lamp ControlBasic Operation PIN Code Input Dialog BoxBasic Operation Turning Off the Projector Direct OFF FunctionTop Control Basic Operation How to Operate the On-Screen MenuRemote Control On-Screen MenuBasic Operation Menu Bar ④ Image adjust⑦ Setting ① InputAuto Setup Function Basic Operation Zoom and Focus AdjustmentKeystone Correction Volume Dialog Box Basic Operation Sound AdjustmentVolume MuteBasic Operation Remote Control Operation Image button Timer buttonNo Show button Screen buttonInput Source Selection RGB Computer 1/Computer Computer InputInput Menu Auto Computer Input Computer System SelectionPC System Menu ModeTo store adjustment parameters Computer Input Auto PC AdjustmentPC adjust Menu Auto PC adjComputer Input Manual PC Adjustment Mode free ResetMode free Computer InputComputer Input Image Mode Selection Image select MenuComputer Input Image Adjustment Image Adjust MenuScreen Size Adjustment Screen MenuDigital zoom + Custom adjPosition H/V Digital zoomVideo Video InputInput Source Selection Video, S-video Input MenuComponent RGB ScartComponent AV System Menu Component Video Input Video System SelectionVideo or S-video Select Video , S-video or Computer 1ComponentImage button Video Input Image Mode SelectionCinema Dynamic Standard Cinema Blackboard Green Colorboard ImageColor Video Input Image AdjustmentTint Store Menu Off Disabled Lower reduction Higher reduction ProgressiveVideo Input Noise reductionVideo Input Screen Size Adjustment Setting Menu Language SettingSetting LanguageInput search Auto setupAuto setup Auto KeystoneBackground Power off? p.20Keystone DisplayLogo select Logo Logo and Logo PIN code lock settingsDefault Logo selectCapture CaptureLogo PIN code lock Logo PIN code lockEnter a Logo PIN code Change the Logo PIN code lock settingChange the Logo PIN code Terminal CeilingRear ComputerShut down Power managementDirect on Standby mode TimerClosed Caption To change the code for the remote control Lamp control Remote controlRemote control Lamp controlKey lock Key lock PIN code lockSecurity Key lock and PIN code lock PIN code lock Change the PIN code lock setting Enter a PIN code Change the PIN codeFan Lamp counter resetVideo delay control Fan controlFilter counter Factory defaultFactory default Filter counterInformation Input Source Information DisplayProjector is shut down and the Warning indicator lights red Maintenance and CleaningThen check the matters below Resetting the Filter Counter Maintenance and Cleaning Cleaning the FiltersFilter counter Cleaning the Projection Lens Maintenance and Cleaning Attaching the Lens CapCleaning the Projector Cabinet Lamp replacement icon Maintenance and Cleaning Lamp ReplacementReset the lamp replacement counter Lamp Replace indicatorMaintenance and Cleaning Service Parts No 349Troubleshooting AppendixAppendix Image is distorted or runs off Remote Control doesIndicator blinks or lights PIN code dialog box appearsAppendix Appendix Menu Tree Image select Image Adjust Screen System AutoSettingInformation Appendix Indicators and Projector Condition IndicatorsAppendix Compatible Computer Specifications ON-SCREEN ResolutionAppendix Technical Specifications Optional Parts Appendix PJ Link Notice Control Port Connector D-sub 9 pin Appendix Configurations of TerminalsTerminal Analog RGB Mini D-sub 15 pin PIN Code Lock No Appendix PIN Code Number MemoLogo PIN Code Lock No Dimensions Appendix KR8AC

Related manuals

Manual 2 pages 61.55 Kb